Search Documents

By R. C. Philp, Allan Gibb

INTRODUCTION. THE term matte is applied to smelting-products so extremely diverse in composition and physical properties that it appears impossible to devise any generic formula to represent, chemically, the manner in which the varied proportions of the almost unlimited possible constituents combine with each other. Mattes produced in copper-smelting, in distinction from those produced in smelting-operations in which the recovery of copper is secondary to that of other metals, cover a narrower range in composition. The copper-content of such mattes vary from 20 to 80 per cent., and even this range is much smaller in general practice since it is found advantageous, when possible, to produce mattes with about. 50 per cent. of copper in the first operation. Further, it is unusual that arsenic or antimony occurs in copper-ores in sufficient proportions to form arsenides or antimonides in such quantities that they will separate out from the furnace-products, as is common in lead-smelting. Generally, the mattes produced in copper-smelting are composed mainly of copper (usually greater than 35 per cent.), iron and sulphur, the remaining elements being usually in proportions sufficiently small to allow of their treatment as impurities, rather than as essential constituents of the mattes. In modern practice of smelting copper-ores in blast-furnaces the tendency is to approach pyritic smelting as nearly as pos¬sible, the furnaces being low and the air supplied being largely in excess of that required for complete combustion of the carbonaceous fuel. Hence the atmosphere of the blast-furnace thus used is usually oxidizing or Dearly neutral? and, as a consequence, the reduction of metallic iron that was a necessary evil of former practice is of unusual occurrence in operations where the main object is the recovery of copper. Hearth-accre-

Nov 1, 1905

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By H. T. Hildage

ALTHOUGH Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at. present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed in the near future ; that since 1902 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in, open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New York City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up ,of a "mine" in a large city, and a brief description of some of the "mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

May 1, 1907

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By Thomas H. Leggett

The conditions surrounding this mine are, perhaps, not sufficiently rare or significant to warrant special attention. A certain interest, however, attaches to the locality through the recent discovery of fossil cycads made there by Mr. Charles M. Rolker, of New York, who has repeatedly visited this district, fixing the geological horizon

Jan 1, 1889

By H. L. Marcus, P. W. Palmberg

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by Varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26" +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr, Ni, Sb, Mn, P, Sn, and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

Thomas Haight Leggett, London, Eng. (communication to the Secretary): Mr. Hammond has given us a concise yet complete description of the Witwatersrand gold-fields, and the character of the operations which have resulted in their remarkable development.

Jan 1, 1902

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200' C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

By Robert H. Richards

Tuns truly remarkable machine was built on a preliminary scale in May, 1895. The first full-sized table was built by Mr. A. R. Wilfley, and was used in his own mill in Kokomo in May, 1896. The first table sold for installation was placed' in the Puzzle mill, Breckinridge county, in August, 1896. The mill enthusiasts at first hailed it as the cure for all the ills that flesh is heir to in the milling line. A little later it was found to make losses which were serious, and on this account the table succeeded only to a limited extent in displacing the vanners of the gold-mills. Still later, mill-men in a number of districts throughout the country made special studies of the faults of the machine, and devised a number of ways of grouping supplementary machines to overcome as far as possible the losses, and at the same time retain the benefit of the extraordinarily large capacity accompanied by the production of clean concentrates for which the machine has become so justly famous. I hope to make an exhibit of some of these methods in an appendix to my book on ore-dressing which is now in preparation. These experimenters have not written up the subject, and if they possess all the facts they have not given them out for the benefit of the mining profession at large. The object of this paper is to obtain the facts and to pre¬sent them so clearly that their bearing can be seen by all. To this end two complete series-'of tests have been planned. One (the present paper), to study concentration of galena in presence of quartz; the other (to follow shortly), to study concentration of chalcopyrite in presence of quartz. Some authorities claim that the table does its best work when treating natural products; by this phrase I mean products which have been crushed to pass through a limiting

Jul 1, 1907

By Robert S. Young

During the last quarter-century, exploration for metallic deposits in Maine has been sporadic with peaks generally coinciding with periods of high metal prices. Known cases of regional or semi-regional evaluations are few; most efforts have been local and usually intensive. On the basis of broad geologic groups, the State has been divided into five fundamental environments: ( 1) coastal metamorphic belt; (2) southern volcanic belt; (3) Silurian slate belt; ( 4) northern volcanic belt; and ( 5) Devonian slate belt. Although not restricted to these areas, exploration in recent years has been concentrated in the northern and southern volcanic belts. Notable examples of recent exploration activity, directed to sulfide minerals, include: ( 1) the Knox County nickel-copper-bearing ultramafic rocks; (2) the Harborside (Cape Rosier) copper-zinc deposit; (3) the Second Pond (Black Hawk) zinc-copper-lead-silver deposit; ( 4) the Big Hill-Barrett lead-zincsilver- copper-gold zones; (5) the Parmachenee copper-zinc belt; ( 6) the Moxie Lake nickeliferous peridotite; and (7) the Attean quartzmonzonite molybdenum-copper occurrences. The Second Pond and Harborside prospects appear to be close to production. Systematic investigations for non-metallic deposits appear to have been aimed principally toward limestone, asbestos, diatomaceous earth, and spodumene-bearing pegmatites. Advances in prospecting methods, high metal prices, a favorable business outlook, increasing cooperation from large landholders, and some discoveries support the probability of increased exploration activity in Maine during the coming decade.

Jan 1, 1968

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By Samuel M. Shallcross

The principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania. Since the middle of 1922, the management of the American Lime R. Stone Co. has been under the direction and ownership of the Warner Company, of Philadelphia. To the Warner Company's experience, gained through successful operation of lime plants in eastern Pennsylvania for many years, and the successful solution of material-handling problems

Jan 1, 1937

By George M. Fowler, J. P. LYDEN

T HE relationship of geological structure to orebodies and to the great masses of chert in the Tri-State mining district is of such significance that it prompts a brief recital of the existing information regarding the various periods of structural deformation. We began to note a relationship between structure and orebodies early in our studies of the field, and further work revealed a like relationship of structure to the great masses of chert so commonly associated with the ore-

Jan 1, 1934

William Kent, New York City: I regret that I have not had the time since the Cincinnati meeting to make as complete a study of Mr. Salom's paper as I wished. I regard it as one of the most important papers that have been presented on this subject, and worthy of complete study. I started out, on the limited time I had, on a system of study which I would recommend to any one else who has leisure to complete the investigation. I took the original report presented at the Cincinnati meeting, and selected from it' such tests as had the analyses reported along with the physical tests, giving the amounts of carbon, phosphorus, manganese, etc., taking only those in which all these elements are given.

Jan 1, 1885