Search Documents

By J. H. Slater

THERE is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust con-tains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out, This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage, An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable prod-uct, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates.

Jan 1, 1940

By W. M. Tuddenham, R. J. P. Lyon

In many areas surrounding the orebodies in mining districts rocks have been bleached and altered by the ore-forming solutions and have been oxidized during later weathering processes. A number of the rock-forming silicates have been broken down to clay, sericitic micas and chlorites have been developed, and pyrite may be found hundreds of feet outside the economic limits of the orebody. These halos of altered ground are prime targets used by geologists in many districts to delineate promising sites for drilling. Both in the field and in the laboratory it is often difficult to map these mineralogical changes in the halos in detail without numerous petrologic examinations. The secondary minerals are generally fine-grained, and since conversion of one mineral to another is often progressive, many alteration processes have not proceeded to completion (feldspars to clay to sericite mica). Qualitative detection of these minerals is difficult; quantitative determination is frequently impossible.

Jan 12, 1959

By W. L. Chen

The Batac jig was first introduced in the US for fine coal cleaning in 1973 (Tackett, 1977; Hake, 1976). Since then, a total of six such jigs of various sizes have been installed in five US plants for a total capacity of 2346 t/h. The raw coal size ranges from 19 mm x 0 to 9.5 mm x 0-fraction sizes previously fed to heavy medium cyclones, Deister tables, or water only cyclones. Growing interest in the Batac jig as a replacement for the above equipment is due to the following reasons: • Unlike heavy medium cyclones, no magnetite is required. As a result, the operating cost of the plant is reduced. • The compactness of equipment is unique on a unit ton per hour basis as compared to other equipment. • Solid state electronic control of jig stroke length, frequency, and jig bed depth makes the equipment highly efficient. Installations of Batac jigs in the US as of June 1980 are shown in [Table 1]. Use of the Batac jig is even greater outside the US (Anonymous, 1980; Chen, 1980). Its use is not limited to fine coal but is applied to coarse coal as well, with 102 mm size in the feed (Zimmerman, 1975). In countries where consumption of magnetite associated with the heavy medium system of coal cleaning is considered a waste of iron ore resource, the Batac jig is regarded as the primary choice in the selection of cleaning equipment (Chen, 1980).

Jan 1, 1981

By F. K. Pence

THE reduction of the firing of clay wares to a science has been one of the most difficult problems of modern ceramic engineering. The number of factors involved in the treatment of these wares has been such a complicated composite of the chemical and the physical properties that, according to the old practice, results depended rather on the art of the operator than on any scientific data available. The combined influence of the chemical and physical properties of clay minerals renders it difficult to apply the data obtained in one operation to the forecasting of details to be applied in another. In maturing clay-ware bodies by the application of heat, the chemical reactions involved are, in general, incomplete. The object frequently is to secure a certain physical quality, as density, color, or strength, rather than any particular chemical composition or development: This is more generally true of the so-called crude clay products. In the case of certain more high-grade wares, as the porcelains, it is necessary to reach the temperature required to bring about a certain molecular development or crystalline structure; but even here, time and temperature are at work and must be considered jointly. The conditions attending the firing of clay wares has led to the use of certain devices in the measurement of the progress of the firing process whereby the influence of the various burning factors on the clay composition under fire is indicated. In the simplest application of this practice, samples of the ware itself are so placed as to be drawn for observation at various intervals during the burn. Although the appearance is affected by the quick cooling treatment, by experience, this practice is successfully used, particularly in the brick industry. The settle of the setting of brick, as measured from the top of the kiln may also serve as a guide in the firing operation. Another example is found in the stoneware industry, where the practice of arranging test pieces made of the same composition

Jan 9, 1919

By H. M. Wolflin

SOMEWHAT more than a year ago the writer collected some extensive notes on metal-mine fires and a paper on metal-mine fire prevention and fighting, a summary of these notes, was hastily pre-pared, with the assistance of G. Chester Brown, chief mining engineer, Industrial Accident Commission for the National Safety Council meeting. This summary, which is admittedly incomplete, is submitted in the hope that it will evoke some discussion that may result in a reduction in metal-mine fire hazard along the line. To accomplish such a reduction does not require the application of complicated scien-tific data. The use of just a little care, a small amount of thoughtfulness and a bit of common sense will work wonders. UNDERGROUND FIRE FIGHTING There may be some interest in a short list of con-clusions of a rather general nature that were reached in connection with some recent mine-fire fighting opera-tions. No effort has been made to cover the field; the items have been jotted down loosely, and very hastily, in the order in which they occurred to the writer. Originality is claimed for, only a few of them. 1. Temperature readings and analyses of mine-air samples, systematically taken, are invaluable aids to effective metal-mine fire fighting and recovery opera-tions. The analysis of the return-air samples fre-quently gives a surprisingly accurate indication of conditions existing underground. 2. Employees must be thoroughly trained in the use, of mine rescue apparatus, because a relatively slight difference in the amount of training makes a vast difference in the amount of work they can per-form under oxygen. In general, slender, wiry men make better apparatus men than those of heavy, more muscular physique, although there are frequent excep-tions to any such general statement. 3: Surprisingly high temperatures, up to 165° F. or 170° F. pan be endured for short periods by wearers of mine rescue apparatus if the air is dry, but lower temperatures, 135° to 140° F. are almost unbearable if the air is very moist.

Jan 2, 1922

By Christer Danielsson, Sven Ivarsson

In 1951 the first ton of iron was shipped from West Africa; ten years later the total export exceeded 4 million tons, and an optimistic forecast for 1970 indicates a production capacity of something around 40 to 50 million tons. The quality of the ore varies from normal hematitic concentrates, through naturally enriched hematitic direct shipping ores with comparatively high content of ore fines, to dense, hard, rich lump ores of magmatic character. West Africa is largely composed of folded Pre-cambrian rocks trending generally northeast to southwest. They are exposed over about one third of West Africa and are part of the vast continental plateau which has an average elevation of about 1300 ft in this area.

Jan 3, 1963

By Branko Ladanyi

In reviewing the current issues in rock mechanics, the author puts an' emphasis on problems related with the needs of extrapolation in scale and time, and of establishing proper conceptual models, especially in connection with the most recent large-scale and long-term projects such as underground disposal of nuclear waste. In such projects, where valid case histories will not be available for many years to come, the observational method can only be successful if combined with a proper framework approach, such as general rock mass classification systems and behavioral models.

Jan 1, 1982

By Roscoe Bell

An economic appraisal of the western phosphate industrial potentials made between 1945 and 1948 revealed possibilities for a considerable expansion in the production of high analysis phosphate fertilizer. The most significant facts are: (1) a rapidly increasing and a much larger potential market which might be reached from the western deposits, (2) the existence of large undeveloped deposits of phosphate rock, (3) potential energy from sulphuric acid, coal, or hydroelectric power in the general vicinity of the deposits. The challenge to the mining and metallurgical engineering profession is in the economical development of phosphate mines and in improving processes for utilization of the western ores and the recovery of byproducts to make the expanded western industry satisfactorily compete with the industry in the East and South in meeting the fertilizer needs of the Midwest and Far West.

Jan 4, 1950

By A. J. Lanza

THE prevention of illness among the employees of the mining industry is especially important in view of the importance of the industry, the unsettled conditions of labor, which emphasize the economic necessity for conservation of labor, and for humanitarian reasons. The burden of chronic illness is altogether unwarranted and unnecessary. If the industry is to maintain its labor supply in an efficient manner and keep the standard high, it is essential that it make every effort to keep its labor in good physical condition. The basic principles underlying health conservation are the same for any industry, but they are here applied especially to the mining industry, and more particularly, perhaps, to metal mining, as it is with this phase of the industry that the writer is most familiar, and as it is conceded that metal mining presents more health hazards than coal mining. The first step in the prevention of illness lies in securing employees who are in sound health and free from organic disease. I do not mean that all men who go underground should be physically perfect, but they should be free from organic defects of the heart, lungs, and other organs, or from anatomical defects that would- markedly increase their liability to accident. The number of men working underground in mines in this country whose physical, condition totally unfits them for such work presents-a situation that should not be allowed to continue, and which I believe is 'not equalled in any other, industry in the country. There is but one way to secure men who come up to the required standard, . and that is by a thorough physical examination before employment. I am fully aware of the objections felt toward such a procedure by many employers and employees. There is much to he said on both sides, but to any one who is at all familiar with the mining industry as it is today in this country, and who approaches the matter with an unbiased mind, there can be absolutely no doubt as to the necessity for physical examination. As a purely logical proposition this is self-evident, but there remains the further necessity of placing physical examinations on such a

Jan 2, 1919

By AIME AIME

IN RESPONSE to a request from the president- elect of the Institution of Civil Engineers of Great Britain, Mr. Calvin W. Rice, secretary of the American Society of Mechanical Engineers, prepared a brief history of the joint activities of engineering societies in the United States, from which we have taken the following facts. National Societies Our first joint activities were in collection with the celebration of the eightieth birthday of "Uncle John" Fritz in 1902, and it is of interest to note that two of the members of the original celebration committee, Messrk. . Ambrose Swasey and Jesse Merrick Smith, will be members of the official deputation to England in June. Mr. Rice, also,' was .a member, of the original committee.

Jan 1, 1921

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By P. de Vitry, Willis P. Mould

THE wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. [ ] Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually 3/16 or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired angle. The usual drive is by a 10-hp. motor through a gear reducer, on which are mounted two grooved sheaves, one of which is keyed and the other free running on the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1946

By S. H. Ash

Foreman remains key man in any safety program, as men attracted to the industry must be trained in safety thinking. Diesel engines underground aid safety and widespread use of roof bolting is reflected in reduction of roof-fall fatalities.

Jan 2, 1953

By Charles L. Elliot

Data for mining applications of geophysical activity in the Free World in 1963 has been collected by the Committee for Geophysical Activity of the Society of Exploration Geophysicists. This information has been made available to the AIME and is published here in abstract form with the kind permission of the SEG. The data is based or1 244 responses (51%) to the questionnaires circulated among 475 worldwide organizations engaged in mining geophysical operations and or research. It is believed that the data is a realistic appraisal of actual world geophysical activity.

Jan 8, 1964

By Harold M. Mooney

The most significant trends appear to be an increased use of electromagnetic and geochemical methods. The most promising instrumental developments are airborne electromagnetic equipment, a magnetometer based on nuclear resonance, and reflection seismic equipment operable to depths less than 100 ft. Work in progress may lead to a one-man magnetometer capable of high precision and continuous recording.

Jan 3, 1955

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By Enrique Touceda

As IN the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time. A few years ago, about the only test made to ascertain the physical properties of the product, t except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in, castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 2, 1920

By Richard Moldenke

So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 135 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 tons daily to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved the soundness of his conclusions. With the advent of iron analysis, and in spite of the growing uniformity of the metal through greater tonnage

Jan 2, 1927

By R. Schuhmann

Distribution of material in the fine sizes of a comminution product generally is well represented by the empirical equation [ ] in which y = cumulative percent finer, x = particle size, = distribution modulus, and k = size modulus. Charles found that the energy consumption in comminution is usefully expressed by another empirical relation, [ ] in which E = energy input per unit volume of material, A = a constant, k = size modulus based on Eq. 1, and n = a constant; ( 1-n) is the slope of a plot of log E vs log k. Holmes has presented energy equations similar to Eq. 2.

Jan 2, 1960