Search Documents

By William E. Bonini, Eugene A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey1 for the purpose of delineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Passaic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum.

Jan 4, 1958

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relation- ships proposed by Rittinger,2 Kick,3 and Bond.4 That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes6 developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill.

Jan 12, 1959

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

By Earl L. H. Sackett

This laboratory centrifuge is unique in its low cost and ease of construction, its particular adaptability to problems encountered in an ore dressing laboratory and its simplicity of operation. It will treat a sample of the size ordinarily used in a laboratory flotation test. The centrifuge was designed at the Baroid Sales Division of the National Lead Co., Malvern, Ark., and built in a local machine shop to serve as a laboratory machine which would produce results comparable with those obtained in the large scale centrifugal deslimers in use in our Magnet Cove mill. The apparatus has served quite well in this capacity and has also proved effective as a deslimer on a variety of ore dressing problems. The cost of making this machine was relatively low and it is simple to operate. It is strictly a batch machine, but when operated under proper conditions, gives results which agree quite closely with large continuous-flow machines of the same type. Effective separation of minus 5 and 10 micron material is made in an undispersed pulp in a short time.

Jan 4, 1950

By A. Weiss

Operations Research developments within the mining industry have evolved over the last few years through stages typical of any new technique. By 1965, most companies had passed from mere recognition of the usefulness of operations research techniques to cautious acceptance of and, in some in- stances, to confident utilization of this relatively new tool. This is reflected in the growing interest and increasing participation of mining companies in sponsoring individual papers on the subject published in mining journals or presented in full sessions at annual meetings. Chief among the sources which served, in 1965, as a barometer for measuring operations research progress within mining is the Annual Symposium on the Applications of Statistics, Operations Research, and Computers in the Mining Industry, which is now sponsored by the University of Arizona, Stanford University, Colorado School of Mines, The Pennsylvania State University, and the Society of Mining Engineers of the AIME. Two significant trends were evident in the applications of operations research techniques to problems typical of the mining industry. On the one hand, unique and imaginative O.R. applications were being developed by several companies, government agencies, and at the university level. These techniques were usually developed to solve specific existing problems. On the other hand, there was unmistakable evidence of attempts to look for problems which could be solved with those "operations research" approaches which would involve the use of the digital computer. In the latter instance, solutions may become applications or demonstrations of how the computer can be used in the reduction and interpretation of data, without the benefit of a decision model. This is a common tendency as most companies have computers, at least in their accounting sections, and many operations research solutions require the use of a digital computer. From the applications observed in 1965 and in prior years, the successful techniques have evolved.

Jan 2, 1966

By R. C. Mahon

THE importance of ground water control in glacial drift overlying mines is widely recognized. Adequate handling of the problem results in considerable saving in overall pumping costs, as the cost of pumping the larger quantity of water under low heads from surface wells is more than offset by the decrease in the quantity of water to be pumped from the mine under high heads. Eliminating or partly reducing seepage of water through the ledge reduces moisture content of the ore, a factor especially important in iron ore mines, where a reduction of 1 pct in moisture effects a very material saving. An important though indeterminate saving is also brought about by the elimination of water in the working places underground. The Homer and Wauseca mines of Hanna Coal & Iron Co. at Iron River, Mich., cover 480 acres. When these mines were started it was possible to operate on only one 40-acre tract, as the depth of water over the remainder of the property was too great to permit operation. Although the average depth of the ground water over the area being mined at that time was less than 50 ft it was necessary to pump 1200 gpm from the mine, the greater part from a depth of 750 ft. The slate footwall and graywacke hanging wall are almost impervious, and it was apparent that seepage into the mine was mainly through the iron formation in which the orebodies were located. Analysis of the water in the iron formation showed it to be of the same character as that in the glacial drift, while the water in both walls was heavily mineralized, also indicating that the water passed much more freely through the iron formation. The first attempt to take off the water above the ledge was by means of drainage drifts driven 15 to 20 ft below the ledge, Fig. 1. Various schemes were used to get the water into these drifts: 1—Holes 15 to 20 ft long were drilled from the back of the drifts to the ledge, but these were difficult to drill and blocked easily. 2—Sections of the drifts were blasted down. This gave a large flow for a time but eventually almost total blockup occurred. 3—Raises 4x4 ft were driven above the drifts to within 8 ft of the

Jan 1, 1955

In March 1956 a conference on geochemical methods of prospecting for ore deposits was held in Moscow. This conference was the culmination of a ten-year period of extremely rapid increase in both research and routine application of geochemical prospecting methods in the USSR. This activity was divided among groups centered in extremely widely separated bases of operation, ranging from Moscow and Leningrad in the West, Yerevan in the Caucasus, and Alma-Ata in Central Asia to Chita near the Manchurian frontier in the Far-East. The All-Union Conference on Geochemical Methods of Prospecting for Ore Deposits, as the meeting was called, was the first opportunity for these scientists from many parts of the country to meet and exchange experiences. It also served to introduce members of the different research laboratories located in the city of Moscow itself, where adequate channels of technical communication had not yet been established. As a result of the Conference, it was resolved that a concerted effort should be made for the participants to publish the results of their work. Two books have appeared as a direct response to this resolution. I. I. Ginzburg prepared a synthesis of the field of geochemical prospecting for minerals based on the material presented at the Conference. This volume has been translated into English and is now available. In addition, the individual papers presented at the Conference were assembled into a symposium volume and published in 1957 under the editorship of V. I. Krasnikov. Unless otherwise noted, these two books have supplied the source material for the present appraisal of the status of geochemical prospecting in the USSR. It is thus about four to five years old. In the years following the conference, the literature has carried a substantial volume of technical papers, together with a few monographs pertaining to specialized aspects of geochemical prospecting.

Jan 6, 1960

By Dennis V. D’Andrea, Robert C. Steckley, William C. Larson, Richard A. Dick

A fragmentation experiment was performed in cooperation with Duval Corporation in a porphyry copper molybdenum deposit near the Sierrita pit south of Tucson, Ariz. A 10-hole test blast was detonated to establish relationships between blasthole spacing and the resulting fragmentation. Blastholes were 9 in. in diameter and 110 ft deep. The 10 blastholes contained a total of 17,400 lb of aluminized slurry blasting agent in 50-ft columns with 60 ft of stemming. Blasthole spacings of 25, 20, and 15 ft were tested. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the rubblized material on the surface. The rubble zone at the surface was ideal for in situ leaching. Fragmentation to depths of 110 ft was excellent from the 15- to 20-ft blasthole spacing patterns. Good breakage was also produced by the 25-ft pattern although the effects of the blast were not as obvious. In situ leaching tests were not conducted. However, based on size consideration only, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1974

By J. B. Rather

THE use of sulfuric acid in refining illuminating oils antedates the beginning of the petroleum industry in America by many years. It was used as early as 1792 by Tower in refining "coal oil" in the British Isles, and by 1860 there were 53 refineries in the United States manufacturing "coal oil," most of them using sulfuric acid as a refining agent. Following the completion of the Drake well in 1859, many of the "coal oil" refiners began to use petroleum for manufacturing illuminating oil, and their methods and equipment were adapted so far as possible to this new raw material. The value of sulfuric acid in refining "coal oil" having been established, this reagent was immediately tried and found to be satisfactory in refining petroleum. Notwithstanding the tremendous advances in petroleum technology since that time, sulfuric acid remains today the most valuable and most widely used means for refining petroleum products. EARLY METHODS OF DISPOSAL OF ACID SLUDGE With the almost immediate expansion of the petroleum industry came the problem of disposing of the acid sludge produced in the refining operations. While in 1859, the year of the discovery of the Drake well, a patent was granted for sludge separation and separated acid concentration, most of the earlier refiners, and many of their successors, felt that separation and recovery of spent acid was uneconomical. Accordingly, many of them disposed of the sludge in any way that seemed expedient at the time. It was buried in the refinery grounds, barged and dumped at sea, run into neighboring streams, or dumped into sewers. Some optimists carted it to open pits in the hope that it would either sink into the ground or evaporate. Not so many years ago, the superintendent of an eastern refinery, who was using the open-pit method of disposal, lost a sludge cart, with horse attached, in such a pit. The horse was recovered almost immediately, but its availability for further use was reduced to zero by the loss of its hair.

Jan 1, 1928

By Carlton D. Hulin

THE usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma fades are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacement and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district, The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 per cent may occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible.

Jan 1, 1945

In the time it takes you to read this sentence, you'll be "zapped" by about 40 cosmic rays. Though harmless, their existence is being probed by a team of Texas A&M University physicists. What's most unusual about the research project is the design and location of the telescope required to detect the particles-it's made of fluorescent light tubes and is 457 m (1500 ft) underground at United Salt Corp.'s mine in Hockley, Texas, about 80 km (50 miles) southeast of Texas A&M's College Station campus. Cosmic rays are actually particles smaller than atoms traveling at extremely high speeds. Scientists believe their source is the same as that of starlight, and that these primary particles entering the earth's atmosphere create secondary particles in collisions with oxygen and nitrogen atoms.

Jan 6, 1978

By Edgar Trask

EACH branch of engineering seems to depend on the cooperation and contribution of some other branches to enable it to produce more efficient methods and appliances for man to use. The purpose of this paper is to show approximately the gain in efficiency of self-propelled merchant ships when steel of greater elasticity is substituted for mild steel in some of the strength members and alu-minum alloy is substituted in some of the parts where strength is not essential. The new steel will have some greater strength and a much greater elastic limit in the as-rolled condition, and must be readily weld-able under ordinary conditions of shipbuilding. Naturally, its cost may be more than mild steel, but if the demand is great that excess cost may be reduced to an amount that will make its use more economical than that of the present mild steel. There appears to be a well defined axiom in engineering today that to use the least power to carry a given load the weight of the carrier must be reduced to a minimum. This minimum must be, of course, consistent with the necessary strength, rigidity and durability and it must not be attained at an excessive cost where the fixed charges of the carrier will exceed the savings in, operating the motive power. Recent railroad equipment is a notable example of this, and in these trains alloy steels and aluminum together with less weight per horsepower of the power plant are reducing the weight of the carrier and hence the total power required for moving the paying load. Before considering the application of these metals to shipbuilding, it is well to explain some of the fundamentals of ship design.

Jan 1, 1936

By Ralph Schilthuis

SEVERAL investigators1-8 have reported evidence of the existence of native or connate water in oil-and-gas-bearing strata. Both water and salt have been detected in cores of oil sands that yielded oil and gas exclusively when produced. Electrical logs often reveal unexpectedly low resistivity through oil and gas sands, indicating the presence of some material that is a considerably better conductor of current than oil and gas. Furthermore, calculations9 of the oil and gas content of reservoirs based upon production and reservoir-pressure decline data indicate appreciably lower values than are arrived at under the assumption that the pore space is occupied completely by oil and gas. ORIGIN AND OCCURRENCE OF CONNATE WATER IN OIL-AND-GAS-BEARING FORMATIONS The view has been expressed,10-15 and is generally agreed upon, that the expulsion of oil and gas material from source beds and the subsequent migration and accumulation occurred in the presence of salt water. As the strata that usually form reservoirs for oil and gas were laid down by, or in the presence of, ancient seas, the pore space within the strata must have been saturated with salt water before the entrance of the oil and/or gas. Thus, the accumulation of oil and/or gas in the upper regions of structures suitable for reservoirs must have required displacement of the connate water therefrom. In the absence of any forces other than gravitational, it would be expected that the displacement of the connate water out of the zones finally occupied by gas and oil would be complete, and that the vertical distribution of gas, oil, and water in a reservoir would be strictly in the order of their densities. Apparently, however, surface and interfacial forces that will not permit complete segregation of the fluids are active within the capillary spaces comprising a reservoir. The effects of these forces on both accumulation and production of oil and gas have been the subject of study by a number of investigators. 16-37

Jan 1, 1938

By C. Q. Payne

The art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates hack to the year 1806, when they were employed in Cornwall, their principal developmcnt has taken place during the past 30 years. To Stephen R. Erom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contrib'ution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the mova, ble roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as, for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springe, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to ex-

Jan 1, 1913

By Clement K. Chase

ION exchange recovery of uranium has been proved successful in many operating plants in various parts of the world. First used in column plants processing clear liquors, ion exchange has more recently been applied in basket resin-in-pulp systems. A logical further development is the application of truly continuous processing techniques to the ion exchange recovery of metals, since previous systems have been semicontinuous at best. Column ion exchange is a valuable technique and has been used extensively in South Africa and elsewhere. However, it requires clear liquors. To produce these clear liquors, considerable investment in filter plant and clarification equipment is necessary. In the cases where it is very difficult or impossible to produce clarified liquors, column ion exchange is not so useful. Moreover, some liquors suffer from post-precipitation after clarification, which can become a serious problem.

Jan 9, 1957

By Thomas Fraser, H. F. Yancey

PRIOR to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England's surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pct of the total production of high-rank coal, the Saar and Aachen about 6 pct each, Upper Silesia about 14 pct, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany west of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pct of the total energy requirement, brown coal supplied about 25 pct, and water power, wood, petroleum and alcohol together aggregated only 7 pct. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered extraction of coal was enforced. Each lease comprised a relatively extensive area, which accounts for the generally large size of the mines and mining companies. In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but go pct of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsenkirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G., a State-owned company operating in the Saar, which produced more than 13 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bituminous coal and brown coal, but in 1938

Jan 1, 1946

By Willard P. Ward

IT is the object of the present paper to bring to the notice of members of this Institute, the results of experiments made during the past six months in the manufacture of the alloys of iron and manganese in the blast-furnace. The ores at hand and available for the purpose were brown hematites, containing but a very small percentage of manganese, and various manganese ores containing a small percentage of iron. It is hardly necessary here to call attention to the statements regarding the production of iron-manganese alloys from such ores, which are given by all the well-recognized authorities on metallurgy. Suffice it to say, in a few words, that they hold that the operation is practically impossible, and that in the use of oxides of iron and manganese, mechanically intermixed in the same ore, much difficulty has been found in producing spiegeleisen. Spathic ores, containing manganese chemically combined, are alone recommended for the production of spiegel, and even then it is said that well-managed furnaces produce only about 75 to 80 per cent. of spiegel, the balance of the production being white laminated pig or gray iron.

Jan 1, 1876

By J. G. Puterbaugh

MARCH 31, 1922, undoubtedly will be long remembered as the ending of an important epoch in the coal-mining industry. On that date, contracts fixing the wages and terms of employ-ment at all anthracite mines and at approximately 60 per cent. of the bituminous mines of the country expired. For the past two years, the consuming public has been complaining bitterly against continued high cost of coal. Coal operators employing union labor have felt obligated to carry out contracts entered -into under the direction of the Bituminous Wage Commission appointed by President Wilson, and in order to do this, they have sacrificed millions of tons of business to non-union mines, and millions of dollars in wages that would have been distributed throughout unionized districts have been diverted to the non-union miners, many of whom never obtained the peak wages granted by the Bituminous Commission and others of whom accepted reductions early in 1921. Heretofore, wage contracts have overlapped as to expiration dates in different districts and renewals have had to take into consideration the competitive balance; the present situation is unique in that practi-cally every contract in the country expired on March 31, and the questions now confronting those responsible for the operation. of the coal mines of the country are: 1. Shall the operators that have heretofore employed union labor endeavor to continue contractual relations with United Mine Workers of America? 2. Shall they undertake to operate their mines with non-union labor? 3. Shall they encourage and endeavor to work out some plan of regulation or arbitration by a Government commission such as President Roosevelt appointed to settle the anthracite strike in 1902? 4. Shall the country give consideration to the demand of the miners that the coal-mining industry be "nationalized?"

Jan 5, 1922

By A. Werenfels

After discussing the geology of the Limagne, the surface indications of petroleum, and the recent exploration, the author states that none of the wells were properly located and that oil possibilities of the Limagne have not been adequately tested. NO PETROLEUM, in commercial quantities, is found in France except the small production of the Pechelbronn field (Fig. 1) in Alsace, which produced 75,000 tons in 1923; therefore the test of the petroleum FIG. 1.-KEY MAP. prospects of the Limagne is most interesting. Under the superintendence of M. Termier, chief engineer of the French mines, a well near Crouelle (Fig. 2) was drilled in 1921 to a depth of 856.3 m. (2808 ft.); at different depths favorable showings were encountered. The well, however, was abandoned because of drilling difficulties. A second one is now being drilled near the same place.

Jan 12, 1924

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 ft and diameters of over 30 in., have become numerous and widespread. 50 such holes have been drilled for access shafts to LPG mined caverns. Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-in. diam with 1600-ft depths, 120- in. diam with 570-ft depths, and 72-in. diam with 4800-ft depths. Equipment is now available to drill a wide range of big holes for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of big holes. The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The purpose of this paper is to present a review of the big hole drilling equipment available, a compilation of the available data on large-diameter holes, to show the experience obtained to date and to show that big hole drilling is feasible and available to the industry.

Jan 12, 1965