Search Documents

By Eduardo Amado Marconato

Na usina siderúrgica de Cubatão da Usiminas, o forno de reaquecimento de placas do LTQ2 utilizava como gás combustível a composição de gases de coqueria, alto forno e natural. A partir da interrupção da produção das áreas primárias (Redução e Aciaria) em Cubatão, o equipamento precisou ser adaptado para uso exclusivo do gás natural como gás combustível. Além das adequações feitas nos sistemas de controle de combustão foram adotadas ações para redução do consumo de combustível como desenvolvimento de novos procedimentos de acendimento do forno, reduzindo o número de queimadores ligados visando aproveitar melhor o calor gerado pela combustão do gás natural. O sistema de combustão foi reconfigurado, permitindo reduzir a temperatura da zona de pré-aquecimento e o tempo de permanência no forno, com isso a economia alcançada no consumo térmico superior a 7%.

Oct 30, 2017

By Rafael Kogake

A termoelétrica de cogeração é responsável pela produção de 2 produtos, eles são vapor de processo e energia elétrica. O vapor de processo tem uma capacidade de produção de 90 t/h, atualmente tem uma produção em média de 65 t/h para fornecer aos consumidores da usina, a energia elétrica tem a capacidade de produzir 200 MWh, atualmente tem uma produção em média de 155 MWh, como o consumo interno do complexo siderúrgico é de 138 MWh médios, a energia elétrica excedente cerca de 17 MWh médios é fornecida para o sistema elétrica nacional, gerando uma receita para empresa com a venda de energia elétrica. A termoelétrica teve um papel importante para o início das operações do complexo siderúrgico pois para as áreas começarem a produzir era necessário o fornecimento de vapor de processo e energia elétrica.

Oct 30, 2017

By Alexandre de Freitas Gomes de Mendonça

O sistema de detecção de rompimento de pele monitora a estabilidade da transferência de calor no molde. Quando é observado desvio de temperatura no molde, esse sistema aciona um alarme e reduz a velocidade de lingotamento para evitar um possível rompimento de pele. Durante a redução de velocidade, alguns aços podem sofrer alteração dimensional e agarramento de placa no veio, podendo ocasionar a interrupção da série. O aço ultrabaixo carbono com alto teor de silício e alumínio, aplicado a indústria elétrica, apresenta esse comportamento. Para melhorar a estabilidade de lingotamento reduziu-se 10% do teor de alumínio no aço. Em termos práticos, o que se observou foi a melhora na estabilidade operacional, pela redução de aproximadamente 83,7% dos alarmes falsos de rompimento de pele. A adequação do projeto de liga do aço não alterou as suas propriedades eletromagnéticas.

Jul 30, 2018

By Severino Albani Junior

A Gestão de Ativos vem ganhando espaço no contexto industrial ano após ano principalmente após 2014, quando ocorreu o lançamento da ABNT NBR ISO 55000. Dentro desse contexto, o tema Manutenção e principalmente a Confiabilidade foram explorados pela ArcelorMittal Flat Carbon South America com o lançamento em 2013 do Plano Diretor de Manutenção e Gestão de Ativos. Este trabalho visa mostrar as etapas seguidas na aplicação de técnicas de Engenharia de Confiabilidade, os atores necessários para a realização do trabalho e os resultados positivos alcançados. Dentre os resultados está a definição da estratégia da manutenção focando a manutenção baseada em condição, possibilitando a otimização dos recursos envolvidos e influenciando positivamente na redução da taxa de falhas da Máquina de Lingotamento Contínuo 01 da ArcelorMittal Tubarão. Estes resultados também levam a expressivos ganhos financeiros, além de melhora da previsibilidade operacional.

Oct 30, 2017

By Jan Krull

A high productive coke making process in connection with stringent emission control has clearly become a demand of plant operators and stakeholders. Further to this, availability, quality and coal costs are key concerns for the iron and steel industry in its efforts to optimize raw material cost. Today, the optimization of raw material cost in integrated steel works has further gained priority. Coking coal reflects up to 20% of the cost of steel. In top charged batteries coal preparation and blending is one of the concerns to lower coal cost by maximizing the percentage of non-coking coals in the blend. Stamp charging technology is technologically and economically an effective solution in the process of pre-carbonisation. Paul Wurth’s jumbo top charged oven as well as proven stamp charging technology have recently set new benchmarks in Europe, India and Brazil in terms of productivity, stability and emission control.

Aug 1, 2018

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Aloizio Cesar Gonzaga, Leandro de Paula, Ismael de Souza Dias, Gladston Santos

Looking for greater competitiveness, Gerdau started in 2013 the operation of its hot strip mill in Ouro Branco, being a milestone in Gerdau's history, where it definitely entered the flat products business. This mill consists of the reheating furnace, primary scaler, a Duo-reversible Quadrupole Steckel mill, accelerated cooling and final coiling. The Steckel mill works with two backup rolls and two working rolls, the backup rolls being responsible for supporting the rolling forces and the working rolls for shaping and surface quality to the strips, having as main requirement quality of surface finish. These rolls suffer high wear due to the lamination process and are exchanged with high frequency to ensure the quality of the laminated strips, after the exchange are sent to the Work Roll Shop for grinding and are positioned Grinded work rolls for the next planned change. This movement is accomplished through the crane and an exchange device that attaches to the cylinders to be transported from the Rolling Mill to the Work Roll Shop. The target in this article is focused on an improvement in this Device to increase operational safety and reduce stoppage losses downtime at the mill, improving the cost / benefit ratio and increase production.

Oct 1, 2019

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By Karl Berger

The paper gives a comprehensive overview of the historical development of various metal rolling technologies and also describes the influence to industrial and socio-economic developments. The rolling of steel, in particular of rails, beams, rebar, strip and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. All this has changed the face of the world significantly. Further the paper approaches technological highlights in the design, manufacturing, drive and control of modern mills and the various types developed to create industrial economic units for the different markets and customers’ requirements. An outlook of future challenges is as well discussed in the paper. Various solution approaches for the rolling technologies, from continuous improvement of existing plants to more radical new concepts like endless rolling, near net-shape casting and rolling are approached. A positive conclusion is drawn that rolling technologies will remain a valuable area for engineers with scientific and economic challenges, but also a clear vision for positive contribution to further industrial and social development.

Jul 30, 2018

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Giselle de Mattos Araújo

A autorredução é afetada por características das matérias-primas tais como granulometria, porosidade, tipo e teor da fonte carbonácea, e também por características do ciclo de processamento imposto, taxas de aquecimento, tipo de atmosfera gasosa, temperatura média de processo. No presente trabalho objetiva-se, através de testes de termogravimetria, avaliar a cinética de autorredução e também o fluxo térmico associado, durante o processamento de diversas associações de finos de minério e fonte carbonácea. Com os resultados obtidos identificam-se condições que otimizam tanto a mistura autorredutora quanto o processamento, observando-se que em uma mesma faixa granulométrica, o maior conteúdo de Cfixo da fonte carbonácea e materiais mais reativos otimizam a cinética, em detrimento da maior quantidade volumétrica de partículas carbonáceas observada em amostras contendo carvões mais pobres em Cfixo. Taxas adequadamente controladas permitem a definição de instantes distintos para as diversas etapas fenomenológicas envolvidas no processamento da autorredução.

Aug 2, 2018

By Daniela Fátima Gomes

O processo de têmpera é uma das etapas críticas na produção de tubos de aço, possuindo grande importância na determinação da qualidade do produto final. Nesse trabalho foi desenvolvido um modelo matemático para o resfriamento de um tubo submetido a têmpera por anéis. Neste processo, o tubo passa através de um conjunto de anéis com sprays de água. Uma série de variáveis afetam a performance do processo, tais como: temperatura de entrada do material na estrutura de resfriamento e velocidades de rotação e avanço do tubo. Diversas simulações foram desenvolvidas, comparando diferentes abordagens para a modelagem. Constatou-se que o espaçamento entre os anéis causa grandes gradientes de temperatura ao longo da superfície do tubo. Verificou-se que a transferência de calor ao longo do comprimento do tubo não deve ser negligenciada e a velocidade de rotação do tubo uniformiza a temperatura ao longo da direção angular do tubo.

Oct 30, 2017

By Camila Peres Massola

Este trabalho avaliou o efeito da corrosão no desgaste de bolas de aço e de ferro fundido branco de alto cromo durante a moagem de minério de ferro, através de ensaios eletroquímicos e de desgaste em moinho de laboratório. Foi feita uma alteração no modo tradicional de realização do ensaio de polarização potenciodinâmica, utilizando polpa de minério de ferro a 70% de sólidos (em peso) no eletrólito. As curvas de polarização obtidas foram compatíveis com os resultados de desgaste, de modo que as curvas correspondentes aos metais na condição mais ativa estavam associadas às menores taxas de desgaste nos ensaios de moagem em laboratório, demonstrando que os ensaios de polarização realizados podem ser utilizados como indicativo do comportamento do metal na moagem de minério de ferro. Verificou-se que, nas condições avaliadas, o efeito da corrosão não foi significativo no desgaste dos corpos moedores, tanto de aço quanto de FFBAC.

Aug 16, 2017