Search Documents

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By J. C. Jansen

The platinum mining industry has experienced a significant increase in fatal accidents. Mine accidents are in principle preventable, and there is enormous pressure on employers to reverse this trend. This paper reviews safety management systems (SMS) as well as behaviour-based safety (BBS). Based on the review, SWOT analyses are performed on the SMS and BBS processes and a model of an integrated safety management system (ISMS) is introduced. A number of fatal accidents is analysed to identify factors that contributed to accidents in the mining industry. Thereafter the potential weaknesses of an SMS of a platinum mine are exposed and the potential benefits of implementing the ISMS for this case study are demonstrated.

Jan 1, 2005

By T. Lindstad, V. Myrvågnes

In the production of high silicon alloys, carbonaceous materials like coal, coke, charcoal and woodchips are utilized as reducing agents. Primarily based on historical prices of charcoal compared to fossil reduction materials, the Norwegian Ferroalloy Industry has mostly been using coal and coke (char) as carbon source. The most important role of the carbonaceous material is to react with the SiO gas to produce SiC. The ability of the reduction materials to bind SiO gas can be measured and the value is recognised as the reactivity of the carbon source. This reactivity is one of the most important parameters in the smelting process in order to obtain a high yield of metal. The reactivity of the carbon materials is directly correlated to the material properties. It is known that the rank of the coal influences the SiO reactivity where low rank is beneficial. Coals of the same rank have however proven to have varying reactivity. In order to investigate how the micro-constituents of coal influence the reactivity towards SiO gas, three single seam unwashed coals of different origin which fulfil the requirements of the Norwegian Ferroalloy producers have been chosen. As the structure in the carbonized product is a function of petrographic constitution and carbonization parameters, the coals have been separated into different density fractions. The various density fractions of the same coals proved to have significantly different petrographic composition. The coals were carbonized according to a procedure simulating the conditions the coals experience when charged to an industrial furnace. Chemical-, physical- and petrographical properties of both the coals and the resultant chars have been thoroughly examined and correlated towards the SiO reactivity.

Jan 1, 2007

OneSteel and BlueScope Steel have been working with the CSIRO to develop sustainable carbon fuels and reductants which are suitable for use in the iron and steel industry. One of the initial focuses of this work has been a process called steel recarburisation which is the addition of carbon to liquid steel to produce particular steel grades. This paper reports on the preliminary work and the recent full scale recarburisation plant trials conducted at the OneSteel Sydney Steel Mill.   Preliminary experimental work involved kilogram scale recarburisation of liquid steel with a range of commercial and prepared charcoal products. This work showed that charcoal dissolves into liquid steel very quickly and that carbon recovery to steel was inversely related to the charcoal volatile content. Initial larger scale work focused on the collection of wood, and preparation of low volatile charcoal which is required for steel recarburisation. Approximately three tonnes of charcoal was prepared at the Corrimal coke ovens of the Illawarra Coke Company. This charcoal was dried, crushed, sized and packaged in a form suitable for addition to 80 tonne liquid steel ladles.   The recarburisation trial was conducted over 30 ladle heats during June 2009. The charcoal was manually added to the liquid steel in 5 kg bags using normal plant practice. Conventional commercial recarburiser was also added to the liquid steel in alternate ladle heats. The performance of the charcoal was compared with the conventional recarburiser based on the carbon recovery to steel, hydrogen pick-up by steel and the rate of carbon dissolution into steel.   An analysis of the trial results showed that the charcoal performed at least as well as commercial recarburiser in carbon recovery and rate of dissolution but may have resulted in a slightly higher hydrogen content of steel. This is probably due to the higher moisture content of charcoal. The main challenges in the future include: increasing the charcoal density to improve transport and handling economics, securing a sustainable supply of biomass for the steel industry and developing a charcoal production industry so materials of suitable quality for both production and trials on other applications can be conducted.

Jun 1, 2010

By F. H. Abd EL-Rahiem

A selective dispersion process is presented and the work carried out to find optimum process conditions to minimise the colouring material in ground calcium carbonate (GCC) is described. The feed material is the overflow product from a hydrocyclone which results from using a Denver Attritioning machine with semi-autogenous grinding for one hour and a 1:1 ore/water ratio. By using sodium silicate (SS), with pH 9 and pulp density 5%, the iron content (as colouring impurities) is decreased from 0.21% in the original concentrate to 0.12% in the final concentrate. The degree of whiteness reached is improved to 85% from 63% in the original material. However, by using hexametaphosphate (SHMP) at pH 10 at the same pulp density, the iron content decreased to about 0.073% and hence the whiteness degree increased to about 96%.

Jan 1, 2004

By K S. Fisher, J D. Pease

The installation of the George Fisher flowsheet in the lead/zinc concentrator at Mount Isa Mines Limited has recently been completed. The George Fisher flowsheet involved moving flotation capacity from the lead circuit to the zinc circuit and changes in zinc circuitry, changes in the reagent regime and increased regrinding capacity, using IsaMills, to regrind some streams to 80 per cent passing seven microns. The project was highly successful, delivering a five per cent increase in zinc recovery within a fortnight of commissioning. The George Fisher flowsheet was developed over six years. Laboratory work built upon the knowledge gained from investigating and processing the Mount Isa and Hilton orebodies. The engineering design and construction for the brownfield expansion of the existing lead/zinc concentrator had significant involvement from the operational, maintenance and technical personnel. Experienced personnel were seconded from the concentrator to the design and construction groups to ensure smooth integration of the new flowsheet into the existing concentrator with minimum downtime, and maximising the reuse of existing equipment. The combination of thorough design, good project integration with operations, and a good commissioning plan allowed almost immediate delivery of project gains. The project was highly successful, the full design improvements were achieved within two weeks, allowing the focus to move to developing future improvements.

Jan 1, 2000

By D. Harrington

This circular is part II of a series of papers reviewing the literature on air conditioning in mines with particular reference to the health, safety, and efficiency of employees. It deals with the physiological aspects of the principal physical qualities of mine air; part I (Information Circular 7001), chapters 1 to 3, discussed the physiological aspects of the chemical qualities of mine air, especially when contaminated with organic matter and noxious and toxic gases; part III will describe theoretical and practical methods of air-conditioning mines to try to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts of tae world. With the present emphasis on the necessity for preserving the health of the Nation's defenders, industrial as well as military, attention should be called to the various conditions that may affect adversely their health and efficiency. One of the most important of these is exposure to abnormal air conditions, especially high temperatures and humidities. Therefore, it is believed that although the data presented here on the physiological effects of exposure to high temperatures cue intended mainly for the mining and allied industries, they are applicable to many other defense industries as well as to conditions present in some activities of the Army and Navy.

Jan 1, 1941

The Epithermal and Mesothermal Gold Prospectivity modelling projects carried out by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250,000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, to stimulate mineral exploration and investment in exploration, has been successful with eight new companies acquiring new tenement positions and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were done at a national scale and consequently not all exploration data were compiled into the prospectivity models. Several of the new companies recognised the value of the prospectivity modelling work and committed exploration funds to continue the modelling process. They recognised a need to compile the remaining data and run the models again to allow detailed exploration targeting. Detailed data compilations including digitising historic exploration stream sediment sample, rock chip sample, soil sample and drilling data has been completed. New models have been completed in Otago for mesothermal gold mineralisation and in the Coromandel and Northland for epithermal gold. The new models have been compared with the original regional scale models and used to target prospect scale exploration. This work has allowed exploration models for epithermal and mesothermal mineralisation in New Zealand to be refined. More importantly this work has identified significant areas with potential to host gold mineralisation with little or no systematic geochemical data including soil sampling or drilling. Exploration work programs have been designed to acquire these missing data and exploration funds have now been committed to test the areas highlighted by the prospectivity modelling. In summary, the Epithermal and Mesothermal Gold Prospectivity modelling work has successfully attracted new investment and ideas to the exploration scene in New Zealand. The projects had an estimated cost of NA$250 000 and will in the next two years, just through exploration expenditure, attract more than NZ$10 M in investment. If a mine is discovered the return on investment will be considerably greater.

Jan 1, 2004

By Pat McLaughlin

Environmental constraints are pushing many operators to change from large rotary blastholes to the smaller diameter holes drilled with down-hole or top-hammer rigs. Productivity improvements over the years with these two drilling techniques has taken some of the bite out of the transition, while improved fragmentation and more uniform muck due to the tighter patterns can help offset increased explosives costs.

Jan 1, 1995

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By C. Sensogut

The phenomenon of spontaneous combustion is one of the major hazards encountered in underground coal mines both from the safety aspects and on economic grounds. Every occurrence, however small, if not tackled effectively in the early stages can develop into open fire, or explosion of gas or coal dust. In terms of economy, even dealing with small incidents may be costly in terms of labour and materials, and in case of a sealing off of a district being necessitated, the loss of face equipment and sterilization of reserves is potentially great. Therefore, expense and effort in prevention and detection of such heating, together with a high state of readiness for dealing with likely event, is completely justified and may be considered as a sound investment. In order to achieve this investment, it may be worth to pinpoint the centre of the fire occurring due to autogenously heating which is supposed to be great assistance to inert it at a least cost and time. Therefore, it is the aim of this work to model the spontaneous combustion in the goaf.

Jan 1, 2002

By R. Marrill

Mining is a complex and intensive industry. Extracting raw material with different shapes, sizes, chemistry from the earth?s crust and transform them into a standardized and high quality final product is a big processing challenge - which involves energy and control on large scales. Not only is the physical work challenging, the mining industry today is facing unprecedented challenges: Decline of mineral grade and reserves, cost escalation for new developments and modernization, regulations, safety, lack of skilled people, and market uncertainty are the new constant. It is clear that process control and management of electrical power will be of increasing importance to the recovery rates the mine will achieve. The objective of this paper is to provide a quick vision about future trends and evolutions in technology related to these fields and their impact on Electrical Safety and Control of the mineral recovery. The paper will cover trends in safety, energy management and efficiency, communications of data, control room evolutions, plant integration, other control technologies, and we will examine how these technologies provide information and the benefits of aligned reporting systems to address current industry challenges. More than just the trends or breakthrough concepts, current technologies are available today that can be applied in the mineral recovery operations now to help overcome anticipated future challenges will be presented later in this document. Finally, a brief discussion to look at some real tools to help make real time changes to the process while maximizing recovery and optimizing cost.

Feb 27, 2013

By M. I. Copeland

The investigation of the iron-gadolinium phase diagram is part of a project undertaken by the Bureau of Mines and sponsored by the Atomic Energy Commission to investigate rare-earth alloys. Data from the investigation of the iron-gadolinium phase diagram revealed a single eutectic system with very limited terminal solubility and three intermediate phases. The eutectic point occurs at about 85 percent gadolinium, and the eutectic isotherm, which occurs at 850° C., extends from the compound Fe2Gd to 99-plus percent gadolinium. Very little solubility of the solid phases in each other was observed. The three intermediate phases, FegGd, Fe3Gd, and FeaGd, melt incongruently at peritectic isotherms at 1,320°, 1,150°, and 1,080° C., respectively. The crystalline systems of the three phases were determined as follows: FegGd, hexagonal; Fe3Gd, hexagonal or rhombohedral; and FeaGd, face-centered cubic. No lowering or raising of the alpha-gamma iron transformation at 910° C., the gamma-delta iron transformation at 1,388° C., or the gadolinium transformation at 1,262° C. was observed. The principal methods used in determining the iron-gadolinium phase diagram were melting-point determinations, thermal analyses, metallographic examination, and X-ray diffraction analyses. Melting, heat treating, and thermal analyses were conducted in a vacuum or under a helium atmosphere because of the avidity with which oxygen combines with gadolinium at elevated temperatures. A few hardness values were determined, but they had no part in the derivation of the phase diagram. No other mechanical properties were determined.

Jan 1, 1962

Alluvial gold was found in the Terawhiti area, West of Wellington, in the 1850s. This led to the discovery of reef gold. Periods of minor 'gold fever', company flotations, and mining activity occured between 1869 - 1973, 1881 - 1986, and in the late 1880s, with one final company active in 1911 - 1914. 1n the early 1980s, further field work was carried out. No viable mining operations resulted from any of this activity.

Jan 1, 1993

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009