Search Documents

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Part III reviewed the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona. Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and a P80 of 6 to 7 µm), pressure leaching at 160ºC with 1,380 kPa (200 psig) oxygen overpressure, DEW to produce LME Grade A cathode, recycling some of the lean electrolyte to the pressure leaching step, and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an acid-autogenous process for pressure leaching. This paper (Part IV) discusses the development and design of a full-scale commercial application for the Morenci operation in Arizona.

Jan 1, 2007

The Khanong supergene-enriched copper resource, (~23 Mt at 3.0 per cent Cu), is one of several resources recently discovered in the intrusive-centred, sediment-hosted Au-Cu Sepon mineral field located in southern Lao PDR. The unusual style of hypogene mineralisation and unique set of conditions have resulted in the development and preservation of a supergene-enriched profile in this subtropical climate. Hypogene sulphide-rich mineralisation replaced calcareous cataclastite (fault rock) developed in the flat-lying, extensional, Khanong Fault. Spatially, the hypogene mineralisation was immediately out board of the skarn û hornfels Cu-Bi front and in board of sediment hosted Au-(As-Sb) mineralisation in a zoned intrusive-centred hydrothermal system. In situ supergene enrichment of the sulphide protore has resulted in a high-grade chalcocite-clay zone (~10.3 Mt at 4.6 per cent Cu) overlain by leached limonite-clay. A very high-grade in situ to exotic limonite-clay Cu-oxide-mineral zone is locally developed above impermeable dolomite at the base of chalcocite-clay zone. Exotic Cu-Mn-wad mineralisation developed for up to 1 km down the hydraulic gradient from the chalcocite-clay zone. Unique supergene enrichment conditions have resulted in the high-grade Khanong Cu resource in a subtropical weathering environment. The base of the currently active supergene profile coincides with the base of a flat-lying, pyrite-rich fault rock, dipping parallel to the hill slope, maximising Cu enrichment. Meteoric water has been channelled along subvertical faults and narrow horizontal subsurface zones. Low permeability of the fault host rock and footwall rocks has controlled the low volume and slow movement of groundwater required for supergene enrichment. Erosion has been slowed by the resistive ironstone and limonite-clay layer at surface, which assists in preserving the gentle slope over the chalcocite-clay zone.

Jan 1, 1999

By J Ramezani, K Faure, N Mortimer

Western New Zealand can be regarded as a rifted continuation of eastern Australia. Detailed studies of units previously considered to have trans-Tasman correlations are being undertaken within the FRST Programme Mineral Wealth of NZ and its EEZ to test specific connections, and thus add to the exploration framework of NZ. Correlation of two major episodes of granitic magmatism are currently being investigated. These represent the oldest (mid Paleozoic) and youngest (Early Cretaceous) magmatic events that conjoined Australia and New Zealand are believed to have in common.

Jan 1, 2007

Objective To develop safety training tools for mine health and safety trainers that fill gaps in currently available materials and help capture the wisdom and knowledge of “expert miners.” Background NIOSH began a series of stakeholder meetings in 1998 to determine what research was needed to improve miner health and safety. One of the more common concerns among stakeholders was a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants provided many insights into what effective training materials should include and how materials could best reach both new and experienced miners. The most important factors were that any materials be realistic and interesting and that some way must be found to capture the wisdom of expert miners before they retired. Approach NIOSH researchers chose videos as the best means of achieving these training goals. Over the past 3 years, NIOSH has produced three training videos that present information on safe work practices in underground mines: handling explosives, recognizing roof hazards and using proper scaling techniques, and installing ground supports. The last two videos, “Rock Falls—Preventing Rock Fall Injuries in Underground Mines” and “Miner Mike Saves the Day—or—Ground Support…It’s Important,” have won Alice Hamilton awards, NIOSH’s highest recognition of Excellence in Occupational Safety and Health, in the Educational Materials category. Two new videos are now being released. Both of these videos were shot completely in operating underground hard-rock mines and used expert miners to tell the story. Hazards In Motion The first, “Hazards in Motion,” deals with the dangers of working around mobile equipment in an underground mine. Ben, a new trainee, refuses to pay attention in his 40-hour New Miner Training class, and when the class takes its first trip underground, he wanders off and finds himself in many dangerous situations. He encounters many experienced miners who both chew him out for his unsafe attitude and give him advice and information on how to survive around mobile equipment. Many common pieces of equipment are shown, including haulage trucks, LHD=s, tracks and trains, slushers, skips and hoists, and air doors. The dangers of ignoring signals and of horseplay are also included. After nearly losing his life numerous times, Ben learns his lesson with the help of the Safety Angel, an experienced miner who looks suspiciously like his safety trainer. Ben’s Safety Angel saves his life repeatedly, teaches him how to work safely around these common conveyances, and introduces him to experts who have specific safety tips. Ben learns the error of his ways and vows to be the safest miner in the mine. “Hazards in Motion” is approximately 30 minutes long. Hidden Scars The second video is the first in the NIOSH “Expert Miner” series. “Hidden Scars” is a narrative interview with Don Capparelli, a miner and supervisor at the Sunshine Mine in north Idaho. This video captures the story of a fatal rock burst in May 1994, when Don was seriously injured and his long-time partner, Jimmy Findley, was killed. “Hidden Scars” is a very powerful story. Don Capparelli shares the physical and emotional pain he lives with daily as he relates the events leading up to the rock burst that took the life of his best friend and partner. This video is an excellent reminder of the human cost of uncontrolled accidents and the hidden scars that survivors must deal with for the rest of their lives. It runs approximately 25 minutes.

Jun 1, 2001

By Fanke Meng

Electrolyzing oxides of titanium, aluminum and niobium could prepare high-Nb bearing TiAl alloy (Ti-45Al-9Nb) at 1500°C. The chosen electrolysis voltage is 3.5V, which is lower than reducing voltage (~4.7V) of electrolyte CaF2, but higher than that of titanium, aluminum and niobium oxides. The investigation shows that compared with traditional methods, this method for preparing high-Nb bearing TiAl alloy is of many advantages such as few steps, friendly environment, low energy consumption, low cost and high current efficiency.

Jan 1, 2009

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

The 70th Regular Meeting of the Rocky Mountain Coal Mining Institute convened at the Steamboat Village Inn, Steamboat Springs, Colorado, and was in session at 10:00 a.m. The session was called to order by Past President O. F. Lewis. Consultant, Colowyo Coal Co., Denver, Colorado. Mr. Lewis introduced President A. F. Geiger, Manager, Navajo Mine, Utah International, Inc., Fruitland, New Mexico. Following are Mr. Lewis' remarks: Ladies and gentlemen, members of the institute, guests and friends, welcome to Steamboat Springs and the 70th meeting of the Rocky Mountain Coal Mining Institute. From all appearances this is our largest meeting and should be the most successful. When I last spoke to you I was President of Colowyo Coal Company and the Rocky Mountain Coal Institute but that has changed. Colowyo Coal Company was acquired last Dec. by W. R. Grace & Co. and operates as Colowyo Coal Company, Division of W. R. Grace & Co. I am confident these people will make a worthwhile contribution to the coal Industry.

Jan 1, 1974

By A. C. du Preez

The separation of nickel and cobalt from calcium, magnesium and manganese by solvent extraction using synergistic mixtures of carboxylic acids was studied. Addition of certain viable synergists to commercially available tertiary branched carboxylic acids, such as Versatic 10 (Shell) or Neodecanoic acid (Exxon), produced large synergistic shifts (?pH50) in the pH50values for nickel, and small antagonistic shifts (negative ?pH50values) in the extraction of calcium. Under the initial test conditions used (0.50 M each of Neodecanoic acid and the Mintek synergist, in xylene) a large separation (pH50Ca? pH50Ni= 3.09 pH units) between nickel and calcium in their extraction from 1.00 M sodium nitrate solutions was obtained, compared with only 1.11 pH units in the absence of the synergist. The selectivity series for the extraction of divalent base metals from 0.333 M sodium sulphate solutions by 0.50 M Neodecanoic acid and 0.25 M of the Mintek synergist in C12-C13aliphatic diluent was found to lie in the order (with pH50values in parentheses): Cu(3.42) > Ni (5.08) > Zn (5.58) > Co (5.73) > Mn (6.62) > Ca (7.48) >Mg (8.25). In batch counter current experiments, a simulated leach liquor containing (in gL-1): Ni 5, Mg 5, Mn 2, Co 0.5, Ca 0.5, Cu 0.1and Zn 0.1 was contacted with the mixed extractant in three stages at unit phase ratio and an equilibrium pH of 5.9. The recovery of nickel was 99.9 per cent and that of cobalt was 84.7 per cent, whilst the co-extractions of manganese, calcium and magnesium were 2.7,1.5 and 0.04 per cent, respectively. The recovery of cobalt can be enhanced by employing a slightly higher pH, although this will also increase the extraction of manganese, calcium and magnesium somewhat. Nearly quantitative stripping (99 per cent) of nickel from the loaded organic phase was achieved in a single contact at an organic-to-aqueous phase ratio of 4 using a simulated spent electrolyte containing 39 gL-1sulphuric acid and 33 gL-1nickel,thereby producing an ?advance electrolyte? containing 57 gL-1nickelat pH 3.5. Loading of acid into the organic phase was very slight, amounting to only 0.002 M H+in contact with the above-mentioned spent electrolyte. Keywords: solvent extraction; synergism; nickel; calcium; carboxylic acids.

Jan 1, 2004

By A Kemp, I Taylor, S C. Lamoureux

Detailed landform designs were completed for six (integrated) iron ore waste rock dumps at a Western Australian iron ore mine site to meet closure objectives and to optimise material movements for closure. The designs were based on specific physical and geochemical properties of waste material and the design was undertaken to enhance long-term stability of the dumps and optimise material movements, and therefore minimise closure cost. Construction of the re-shaped waste rock dumps have been completed. Following construction, surface material characteristics were found to deviate from those used in the design assessment. Materials present at surface following re-shaping were generally finer textured than those sampled for modelling. It is anticipated that the embankment slopes may experience increased rates of surface erosion compared to the rates predicted from modelling and used in design. The finer textured material is thought to be generated from exposing finer material that has migrated into the coarser matrix over time or that was not present in the sampled top surface of the landforms. This is due to armouring processes over time and this phenomenon is likely to recur following further wet seasons. The majority of the waste materials present in the waste rock dumps were subgrade banded iron formations (BIF) and chert, which are generally competent and geochemically inert. Some waste material was known to have an elevated risk of erosion but present in relatively small quantities. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert). This paper presents the process from upfront materials assessment through detailed design to construction of the rehabilitated waste rock dumps, and post-construction sampling and testing to validate model findings.CITATION:Kemp, A, Taylor, I and Lamoureux, S C, 2017. Design to closure – construction of detailed rehabilitation designed iron ore waste rock dumps based on upfront site specific assessment, in Proceedings Iron Ore 2017, pp 353–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased or decreased), and provides a bridge where possible from the old Schedule A classification sys tem to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

By Andrew M. Leszcykowski

A 1981 U.S. Bureau of Mines investigation indicates the Panamint Dunes Wilderness Study Area (WSA) has one active (intermittent) mine,--borrow pit MS 242 owned by the California Department of Transportation (Cal Trans). This mine produces cinders for road base and traction grit. It contains about 900,000 tons of inferred reserves. Examination and sample analyses indicate the Panamint Dunes deposit, covering about 480 acres of the WSA, may have silica resources and the Green Quartz Claim may have copper resources. Carbonate rocks occur in the WSA, but stone resources have not been identified. Adjacent to the WSA, the Big Four Mine contains 35,000 tons of inferred subeconomic zinc-lead-silver resources, and may have additional resources. Sample analyses indicate the Apple 1 Claim, also adjacent to the WSA, may have silver-lead-zinc resources.

Jan 1, 1985

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

By D J. Corp

The Halmahera Contract of Work is a sixth generation contract held 82.5 per cent by Newcrest Mining Limited and 17.5 per cent by PT Aneka Tambang and takes in the Gosowong Project area. In 1991 Newcrest Mining Limited established a small exploration office in Jakarta and proceeded to seek exploration opportunities. The Halmahera area was identified as a substantial prospective ground position in a relatively unexplored area. In late-1991 Newcrest Mining Limited and PT Aneka Tambang agreed to explore in Halmahera. Initial field work commenced in July 1992. A vigorous ground reconnaissance programme led to the discovery of the Gosowong deposit a little over 12 months later in September 1993. In April 1997 the Contract of Work was approved covering much of the island of Halmahera. Between September 1997 and November 1998 activities were directed principally towards obtaining the necessary permits required to commence construction activities. Some particularly ambitious targets were set for achieving this outcome. An aggressive construction programme commenced in late-1998. Construction took place during a period of unseasonally high rainfall, which in itself presented additional challenges to the construction team. A key milestone for the project was achieved on 1 July 1999 when wet commissioning of the process plant commenced. Construction of the Gosowong Mine was achieved on time and within budget. A period of some six years elapsed from the initial discovery of the Gosowong deposit to the time of the first gold pour. Much of the permitting, construction and commissioning activity took place between September 1997 and July 1999. This coincided with a period of significant social, economic and political upheaval in Indonesia. During the construction period a high level of importance was placed on the structured recruitment and training of local people, as well as fostering appropriate community and local business development programmes in the communities nearby the project. Emphasis was also placed on environmental management with detailed long-term planning and progressive rehabilitation commencing during the construction phase. The permitting and subsequent development of the Gosowong Project has demonstrated that even during the difficult times, with commitment, it is possible for mining and exploration companies to conduct business in Indonesia.

Jan 1, 1999