Search Documents

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By D. S. F. Silva

A survey of 120 recent NI 43-101 technical reports was conducted to evaluate the current state of practice regarding resource classification techniques. The most common classification techniques are based on search neighbourhoods (50% of recent reports), drill-hole spacing (30% of recent reports), and/or kriging variance (6% of recent reports). Two new techniques are proposed. The first is based on kriging variance and involves removing one or more drill-holes with the highest weights while performing kriging and using the resultant kriging variance for classification. This technique has the advantages of variance-based techniques and reduces artifacts. The second technique is based on conditional simulation and uses a moving window approach for classification at the desired selective mining unit resolution based on larger production volume criteria. This technique has the advantage of accounting for heteroscedasticity, which is a common characteristic in mineral deposits, and also reduces artifacts since a production volume scale is considered for the actual classification. The drill-hole spacing, search neighborhood, kriging variance, and simulation-based techniques are described and compared for 2D and 3D examples with regular and irregular drilling patterns to highlight the advantages and disadvantages of each method.

Jan 1, 2014

By K. B. Bengtson

This task report provides the process technology, preliminary design, capital and operating costs for a 25 TPD pilot plant to produce cell-grade alumina using a clay/hydrochloric acid extraction - HCI gas induced crystallization process. The report consists of six volumes: I - Process Technology and Costs; II and III - Equipment Lists, Specifications and Quotations; IV and V - General Specifications; VI - Drawings. The process was selected by the Bureau of Mines as the more promising method to produce cell-grade alumina from clay based on the results of the two previous task reports under this contract: Task I - Comparison of Six Processes (alunite, anorthosite-lime sinter, clay/sulfurous acid, clay/nitric acid, clay/hydrochloric acid evaporative and gas-induced crystallization) and Task 2 - Comparison of Two Processes (clay/nitric acid and clay/hydrochloric acid - gas induced (crystallization). The pilot plant process utilizes a unique dual crystallization process to produce aluminum-chloride-hexahydrate crystals having sufficient purity when decomposed to meet stringent alumina product specifications. The size of the 25 TPD pilot plant has been selected to permit scale-up to commercial size plants of equipment, technical and economic parameters. The capital cost estimate for the pilot plant, exclusive of fee and escalation, for a southeastern U.S. location is $52,311,000 expressed in 1979 dollars. The total time required to construct the pilot plant including engineering and procurement is 32 months. The operating cost to produce the estimated 9,000 tons of alumina required for testing in Hall cells is $40,91[0],190 expressed in 1979 dollars.

Jan 1, 1979

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

Some low grade South Australian iron ores were classified on the basis of their physical characteristics. Ores from Mount Christie and Billeroo are coarse grained mixed ores; Mount Christie ore could be concentrated by gravity or dry magnetic separation at 10 mesh, but Billeroo ore needed to be crushed minus 36 mesh. Ores from Razorback Ridge and Wilgena Hill are fine grained mixed ores; ore from Wilgena Hill could be concentrated by flotation, but poor results were obtained on Razorback Ridge ore. Malcolm Creek ore is non-magnetic and crystalline, and can be concentrated by flotation, but the deposit is small. Ores from Grants Quarries and Peeralilla Hill are nonmagnetic and earthy and could not be satisfactorily concentrated.INTRODUCTIONThe Geological Survey of South Australia has for several years been undertaking a systematic study of the iron ore resources of the State (excluding the Middleback Ranges) in relation to their geology, reserves, and beneficiation. As part of the latter phase of the investigation samples of the ores have been submitted to The Australian Mineral Development Laboratories (AMDL), and it was the study of these samples which provided the material for this paper.The mineragraphic and metallurgical work was undertaken by several officers of AMDL and the results are contained in unpublished reports submitted to the South Australian Department of Mines. Field data published here was obtained from unpublished reports by G. F. Whitten, Senior Geologist, Iron Exploration, of the Geological Survey of South Australia.

Jan 1, 1964

By M. Superfesky, P. Michael

Introduction The US Office of Surface Mining (OSM) is proposing changes to the Code of Federal Regulations in the interest of minimizing the adverse effects of excess-spoil-fill construction on the “prevailing hydrologic balance, fish, wildlife and other environmental values” (70 FR 35112). The proposed changes will require: (1) minimization the amount of excess spoil generated at a mine site; (2) minimization of the size of the fills constructed; (3) consideration of alternative configurations for disposal; and (4) development of a disposal plan that would minimize adverse impacts to the environment.1 To achieve those objectives, mining companies operating in steep-sloped Appalachia will likely build excess spoil fills (also called valley fills) that toe out at higher elevations in the hollows (i.e. to prevent or limit burial of streams). Consequently, the slopes of fill foundations will generally be steeper. Whereas the authors of this paper support these measures to protect the hydrologic balance and general environment, we wish to point out that placement of fills on steeper foundations can negatively impact the stability of the fills if proper care is not taken during their construction. It is important to note that in addition to impairing human safety, valley fill instability can negatively impact streams, the riparian habitat etc., and thus defeat the very purpose of the spoil minimization measures proposed. We do not, however, propose additional regulatory requirements pertaining to valley fill stability. Rather, we intend to emphasize the importance of engineering requirements already on the books, especially as they apply to the predominant type of valley fill constructed: the durable rock fill. We believe that the practice of restricting valley fills, to higher elevations in the watershed leaves less room for error in the design and construction of stable structures. This paper gives a quick review of the nature of excess spoil generation; methods and requirements of excess spoil fill construction, and the to-date stability record of the fills. The interest in excess spoil minimization and how it affects valley fill construction is also discussed. Most importantly, we will review long-standing issues pertaining to proper design and construction measures with respect to durable rock fills and discuss how they will become more critical as spoil minimization is practiced.

Jan 1, 2007

As part of the Bureau of Mines program for conserving domestic mineral resources, a survey was made of the methods used for identifying scrap metals. Because of the large number of alloys currently being scrapped, correct identification of these materials is essential if they are to be recycled effectively. The methods and instruments used to identify scrap metals are described and evaluated. These include object recognition, color, density, magnetic testing, spark testing, chemical spot testing, thermoelectric measurements, eddy current measurements, and elemental analysis by chemical and instrumental methods. Other potential techniques are discussed also.

Jan 1, 1982

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By R. P. Singh

A mine fire model gallery has been designed and constructed on the premises of the Central Mining Research Institute, Dhanbad, India to perform systematic in-depth studies on various aspects of mine fires. The gallery is 65.5 m long and 5.86 m2in cross-section and it is divided into firing and non-firing zones. It is equipped with a computer-aided online telemonitoring system that has 130 sensors, two data loggers and computer peripherals for continuous recording of various fire parameters. A fan to generate airflow through the gallery has been installed at its end. Two sliding doors and one rolling shutter were also provided for sealing and regulation of airflow. Two sets of experiments have been carried out in the model gallery maintaining air velocity of 1 and 1.5 m/s through it. In the experiments, the inner sides of the firing zone, 22 m in length, were lined with a thin layer (8?10 cm thick) of coal slabs. Two fire suppression techniques viz. flushing of liquid nitrogen (LN2) and infusion of high pressure high stability (HPHS) nitrogen foam were tried to quantify their effectiveness under dynamic fire conditions. The paper addresses important design features of the gallery, its instrumentation system, the experimental procedure adopted and important findings from the experiments. It has been observed that the intensity of the fire was very high after one hour of its initiation and continued for 3?4 hours. During the period, frequent backlash with smoke and flame was noticed. The efficacy of the fire suppression techniques has been assessed interms of reduction in temperature, generation rate of CO2and CO, and heat release rate. The study reveals that high pressure high stability (HPHS) nitrogen foam is more effective in controlling open fires than liquid nitrogen is. Keywords: Model gallery, telemonitoring system, velocity, temperature, pressure, gas concentration, intensity, liquid nitrogen, high pressure high stability nitrogen foam.

Jan 1, 2004

By Thomas Donnelly

Introduction THE Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineralization is found about 1.-CAMP BUCARO. THE TOP OF THE RIDGE IN THE BACKGROUND MARKS THE CONTACT OF THE LIMESTONE AND TUFFS. S miles north of the town of San Cristobal, in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina (Liver. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horse-back 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 8, 1915

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

The addition of copper sulfate to mineral slurries in order to ?activate? sulfide mineral surfaces for enhanced collector molecule adsorption, and hence enhanced recovery via flotation, is a com-mon mineral processing practice. It has been established in a laboratory situation that the addition of CuSO4 in conjunction with xanthate collector increases the flotation rate of pentlandite as compared to the addition of collector alone. However, it remains unclear whether the addition of CuSO4has a similar effect within mineral processing circuits. We examine here the effect of pre-activation oxidation on the copper activation of pentlandite and monoclinic and hexagonal pyrrhotite. All activation experiments were carried out at pH 9 using a total solution content of copper ions equivalent to one monolayer (0.210 -4 moles, 110-4M). Copper loss from solution was extremely rapid in all cases with less than 10 % remaining after 10s. EDTA extraction and solution analysis clearly demonstrated that copper activation was via direct surface adsorption and not an ion exchange process, as is the case for sphalerite, and that most copper on the surfaces is in the form of Cu(I). ToF-SIMS analyses of the mineral surfaces subsequent to copper activation show increased surface oxidation on increased conditioning time prior to copper activation. However, there is a significant decrease in surface oxidation on comparison of samples that have otherwise been prepared in the same manner but where one has been exposed to copper solution rather than water. This suggests that copper activation stabilises the surface and reduces the propensity for oxidation. Regardless of the length of pre-activation oxidation time only Fe(III) (no Fe(II)-S) was observed by XPS analysis, indicating a highly oxidised surface layer dominated by Fe-O-OH species. The presence of Cu(II) on the mineral surface is indicative of the formation of Cu(II)-containing precipitates and indicates non-mineral specific activation resulting in increased recovery but lower grade. Mineral specific copper adsorption, as evidenced by the presence of Cu(I), is required to improve both grade and recovery. Prolonged oxidation prior to copper activation causes a reduction in the Cu(I) to Cu(II) ratio on the mineral surfaces as compared to either fresh surfaces or surfaces oxidised for 1 minute only. This strongly indicates that the copper activation process is less effective on highly oxidised surfaces.

Jan 1, 2014

By Robert H. Peters

The U.S. Bureau of Mines has prepared this report on strategies for maintaining high job attendance among underground coal miners because high absenteeism is a threat to miners safety and seriously hampers productivity. A substantial number of research studies on the effectiveness of various strategies for reducing absenteeism among the employees of nonmining industries have been reported in the literature. These strategies have aimed at improving job attendance through one or more of the following: (1) improving employment procedures, (2) overcoming problems that adversely affect one's ability to attend work, and (3) increasing miners motivation to attend work. Many of these strategies appear applicable to the mining industry, and are reviewed in the first half of this report. The second half of this report describes how one could develop and implement a program for maintaining high attendance at underground coal mines. The steps include: measuring and evaluating attendance levels; formulating attendance goals and an absenteeism policy; developing and implementing an attendance promotion program; and periodically going through the preceding steps known as recycling.

Jan 1, 1989

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. By using eddy current images, it was shown that the eddy current technique could be used to monitor creep damage in a nickel base super-alloy. The eddy current results also show a significative variation in the electrical conductivity on the creep damage zone with respect to the background zone in nickel-base super-alloy samples. In addition, the absolute thermoelectric power coefficient show also a strong dependence associated with creep damage in nickel base super-alloy samples using a copper hot tip reference. The eddy current and thermoelectric power techniques seems to show promise as nondestructive evaluation tools for monitoring the level of creep damage in metallic alloys.

Jan 1, 2010

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By A. D. Davis, C. J. Webb, C. S. Johnson

The Belle Eldridge Mine is an inactive lead-zinc mine in Spruce Gulch south of Deadwood, South Dakota. Acidic mine drainage (AMD) produced at the site drains into Spruce Creek, a tributary of Whitewood Creek. The site is on U.S. Bureau of Land Management (BLM) property. Extensive fieldwork was done at the Belle Eldridge Mine through the cooperation of the BLM and the South Dakota School of Mines and Technology. The site was extensively mapped to identify physical and environmental hazards such as tailings, waste rock, collapsed buildings, adits and workings. An exhaustive search of the historical records of the Belle Eldridge Mine was conducted. Maps of the under-ground workings of the Belle Eldridge dating from the 1930’s and 1940’s were found. The maps were used to correlate currently collapsed features to old adits and tunnels. Using hand corers and a portable drill rig, waste rock, tailings and soil core samples were collected and depth to bedrock was determined and the total volume of waste and tailings pile were determined. Related work examined the hydrology of the site. The site is very complex hydrogeologically. Numerous underground and surface workings and tunnels add to the complexity. Several seeps are located at the site, one of which is producing AMD. Recharge to the site was studied, and a 100-year flood plain map was produced.

Jan 1, 2000