Search Documents

By William L. Fink, Dana W. Smith

Many investigators have attempted to determine the true nature of the internal changes taking place during aging. Merica, Waltenberg and Scottlt were the first to propose a theory of age-hardening. They attributed the age-hardening of duralumin to the precipitation of minute particles of the compound CuA12. Later Zay Jeffries and R. S. Archer2 augmented the above theory by suggesting that the small CuAl2 particles acted as "keys" causing "slip interference." Many other investigators3 have devoted much time to the mechanism of age-hardening, some corroborating the "precipitation" and "slip interference" theory, others coming to different conclusions because of effects that to them seemed unexplainable by the early theories; e.g., the increase of electrical resistance upon aging, the fact that no change in lattice parameter could be detected during the early stages of aging even at elevated temperatures, and the fact that the density did not change as would be predicted. In 1932, Merica revised4 his earlier precipitation theory to take care of these presumably anomalous effects. This revised theory, the "knot" theory, assumes that substantial age-hardening occurs before actual precipitation of solute as discrete particles. The assumed mechanism is one of diffusion of solute atoms into groups forming distorted regions which act as "hard" spots and cause slip interference. These "knots" are assumed to have approximately the same lattice arrangement as the solvent. The anomalous behavior of lattice parameter, density, and electrical conductivity, require a modification of the simple precipitation-hardening theory, only if it is assumed that the precipitation of minute particles during aging has the same effects on these properties as the formation of large particles under equilibrium conditions. Data obtained by the authors in the study of the aluminum-magnesium system5 indicated that

Jan 1, 1936

By John R. Edwards

Introductory.—There are many interesting and important events connected with the petroleum problem. The remarkable men who conceived 'the thought of transporting petroleum by pipe line, conserving the byproducts of the commodity, and conducting extended investigation and research whereby the flash point of the oil was raised, its cost reduced and its supply assured, are deserving of the gratitude of this nation. It was primarily the success attained by Captain Lucas, after his comprehensive search for oil in Texas and Louisiana, that was the impelling cause which prompted the Navy Department to conduct the extensive series of liquid fuel-oil tests that were made from 1901 to 1903. The sensational discovery of oil at Spindle top made a deep impression upon Rear Admiral George W. Melville, then Engineer-in-Chief of the Navy, and the discovery of the vast oil field in Texas convinced him that, within a generation, if not within a decade, crude petroleum was going to play a very important part in warfare, and that the commodity might possibly develop into a necessary munition of war. The United States' Commanding Position as a Petroleum Producer.— In the study of the various problems relating to the world's production of crude petroleum, the position of the United States is one of commanding importance, whether viewed from the industrial or the military aspect. The present yield of this country is practically double that of the rest of the world, and, in view of the productive and prospective fields possessed by various countries, together with the comprehensive and exhaustive search that has been made throughout the world for petroleum, it is extremely probable that this lead will be maintained for the next decade. As regards the character of the crude-oil yield of different countries, America possesses the greater part of the supply that contains a paraffine base, and therefore a considerable portion at least of the American product produces the best illuminant. Of all the crude-oil distillates, kerosene is in many respects thc most important, and the Appalachian product for this purpose is favored, particularly in the Far East, above that of any other petroleum yield of the world.

Jan 1, 1915

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By J. L. Brimhall

Slip-line formation during bending has been studied on neutron-irradiated molybdenum single crystals. For equivalent strains, the slip lines are coarse and distinct in the irradiated molybdenum and not resolvable in the unirradiated molybdenum. The slip lines have been directly correlated with dislocation channels present in the irradiated and deformed thin foils. The heterogeneous distribution of the dislocations during deformation in the irradiated material results from dislocation interaction with the dejects produced during irradiation. Impurities , in the form of' carbides, affected the dislocation channeling Principally by acting as dislocation sources. ALTHOUGH the mechanical behavior of irradiated materials has been studied extensively, the precise mechanism of irradiation hardening has not been established. Some information on the microstructural species responsible for hardening of irradiated materials has been derived from direct and indirect observations. The direct observation of the structure of deformed irradiated metals, particularly by transmission electron microscopy, is a relatively new and unexplored area. Slip-line studies in fcc metals have been restricted primarily to copper.1-3 Very coarse slip lines, representing slip on many closely spaced planes, have been observed in deformed, irradiated copper. Coarse slip lines have also been observed in irradiated aluminum.4 Clear channels in irradiated copper caused by dislocation motion through the defect structure have been seen by transmission electron microscopy and correlated with slip lines.5-6 To date, little work has been reported on the irradiated bcc metals. Eyre described the slip lines around hardness indentations on irradiated iron and found them to be more distinct than lines in unirradiated material.' Mastel et al.' have observed channels in deformed irradiated molybdenum similar to those reported in copper. As part of a program concerned with the effect of neutron irradiation on metals, the slip-line

Jan 1, 1965

By J. R. Kyte, R. L. Dalton, V. O. Naumann, R. L. Ridings, R. W. Greene

This paper presents a one-dimensional numerical method for calculating dissolved-gas-drive behavior for a single well or a linear reservoir. Pressure and saturation distributions can be calculated, including the effects of capillary and gravity forces. The analysis has been programmed for solution on the IBM 7090 digital computer. A comparison of experimental and calculated behavior for two linear models demonstrates that the method is suitable for calculating dissolved-gas-drive behavior under reservoir conditions of flow. Dissolved-gas-drive tests were run, at different production rates and with oils of different viscosities, on short (6.ft) and long (173ft) flow models. For tests approximating reservoir pressure gradients and flow rates, there was excellent agreement between experimental and calculated results. A series of calculations of well behavior for thin, horizontal, homogeneous, dissolved-gas-drive reservoirs shows that ultimate recovery is independent of production rate or well spacing in such cases. These calculations also show that Muskat's method and similar material-balance analyses are not applicable under some conditions particularly for high pressure drawdowns. INTRODUCTION The problem of calculating dissolved-gas-drive reservoir performance has received a great deal of attention throughout the oil-producing indusfry for many years. Really significant advances, however, have been made only in recent years. The rapid evolution of high-speed computing equipment and techniques has opened up new approaches to the problem and led to realistic, quantitative analyses free of many of the assumptions and limitations of earlier methods. The one-dimensional numerical method described in this paper includes the effects of both gravity and capillary forces. A number of test calculations, based on different rates, spacings, and rock and fluid properties, have shown that the method is adequate for systems that can be reasonably represented by a one-dimensional model (linear or radial) and in which fluid segregation perpendicular to the direction of flow is not important. Along with the development of mathematical methods, an experimental program was conducted and the data were used to test the validity of the theoretical basis of the mathematical method. Linear models were used and all experiments were run using 1,000-psig bubble-point oils. The use of long, high-pressure models enabled us to more closely approach reservoir gradients and flow rates. MATHEMATICAL FORMULATION DIFFERENTIAL EQUATIONS The differential equations describing dissolved-gas-drive behavior in one dimension dare summarized here. They include Darcy's law for flow of oil and gas (Eqs. 1 and 2) and the equations for conservation of mass for oil and gas (Eqs. 3 and 4). The oil and gas pressures are related by capillary pressure (Eq. 51.

By F. C. Langenberg

DURING the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point: The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the. bars was tested in this manner and in no instance could any difference in structure be detected between the three specimens.1

Jan 2, 1915

By Tenney, J. B.

DEVELOPMENT of complex ores in the south- western part of the Rocky Mountain region has been retarded by the prohibitive distance to the nearest suitable zinc treatment plants. In the north- western and central Rocky Mountains the building, cluring tlie past decade, of electrolytic zinc plants at Anaconda, Great Falls, Trail, and Burke has tremendously stimulated the mining and exploiting of such .ores, greatly increasing the production of lead, zinc, copper, gold, and silver. Selective flotation permits the making of high-grade led, copper, and zinc concentrates. If the zinc concentrates could be made free from lead, copper, gold, and silver, they could be shipped economically to Mid- Western retort plants designed for such concentrates. Unfortunately a considerable proportion of the precious metal content accompanies the zinc blende in the ores of this region. Although some of it is saved in 'retort residues, the treatment cost is thereby increased so materially and the proportion saved so small, that .concentrates of ordinary grade cannot stand treatment charges and freight.

Sep 1, 1928

By R. H. Storch, D. C. Holt

During reconnaissance investigations of more than 300 stream areas in Idaho to determine the potential value of ilmenite in black - sand placer deposits 46 deposits were explored by churn drilling , trenching , test pitting , or shafting . The component mineral content and total black - sand content were determined for more than 8,690 reconnaissance and exploration samples . Data compiled during the investigation indicate a good potential for large , low- grade deposits containing ilmenite , monazite , columbite , euxenite , uranothorite , and other radioactive black minerals and accessory black - sand minerals . The data also indicate most deposits will be economic only if several component minerals can be recovered as coproducts .

Jan 1, 1963

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By John L. JR. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By Carl Davis

A description is given of grinding practice on the Rand and of experiments made to improve that practice. The paper includes a description of the experimental plants and methods and the results obtained. THE first tube-mill on the Rand was put into operation in May, 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell 22 ft. 0 in. diameter 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.1 By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from. 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a final product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; -90 mesh, 69 per cent.; and the slime grading -200 mesh, 2 per cent.; -200 mesh, 98 per cent.

Jan 12, 1924

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By AIME AIME

IN many countries the lack of liquid petroleum supplies has centered interest upon the hydrogenation of coal and coal tars for the preparation of motor fuel. In the United States, hydrogenation has been of greater interest for grading up low-value petroleum fractions to the more valuable volatile fuels and for the preparation of a variety of premium products, including aviation gasolines, solvents, Diesel fuels, and lubricating oils. Chemically, the basic reason for this process is that, as shown in Table 1, the ratio of hydrogen to carbon (H/C ratio) in available raw materials is quite different from that characterizing the products sought.

Jan 1, 1936

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By H. O. Hofman

At the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper-Smelting,"' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, FeS. They arrived at this inference from the observed fact that a matte containing Cu,S, 90.4, and FcS, 9.6 per cent. (or, in round figures, Cu2S, 90, and FeS, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent. of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent. of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples gave them a grayish-black field of very uniform appearance, except that five of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the ferrous sulphide-cuprous sulphide series, and to see how the constitution could be further revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, " The Concentration of Gold and Silver in Iron-Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1908