Search Documents

By B. R. Eichbaum, J. E. Murphy, J. A. Eisele

The US Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench scale basis. Leaching was performed at 95°C (200°F) and with a contact time of 15 minutes. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 hours. In each test, a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45 hour test, lead extraction exceeded 99.5%, and the lead chloride produced was 99.97% pure.

Jan 1, 1986

By M. Hayashi

The Bureau of Mines conducted laboratory studies on Idaho mudstones to examine techniques for extracting vanadium. Recovery of vanadium from low-grade sources could contribute to future vanadium production and reduce reliance on imports. An Idaho mudstone surface sample containing 0.30 pct V205 and an underground sample containing 0.21 pct V205 were used in the extraction tests. Leaching of the surface sample for 18 h at 800 C with the addition of up to 1,000 lb/ton H2S04 recovered 70 pct of the vanadium. How-ever, leaching of the underground sample under the same conditions re-covered only 47 pct. By adding 15 wt pct NaCl and roasting the samples at 7500 C for 2 h, followed by leaching with 800 lb/ton H2S04, vanadium extractions were increased to 78 pct from the surface sample and 83 pct from the underground sample. Water leaching of samples roasted at 7500 C for 4 h with a 25-wt-pct NaCI addition yielded about 60 pct of the vanadium from both surface and underground samples. Autoclave leaching at 2000 C for 3 h with 1,000 Ib/ton H2S04 extracted 97 pct of the vanadium from the surface sample and 86 pct from the underground sample. An exploratory solvent extraction investigation to purify and concentrate vanadium in the leach solution using several organic reagents was also conducted.

Jan 1, 1985

By F. E. Armstrong

This report describes development and application by the Bureau of Mines of techniques and instruments for using radioactive inert-gas tracers to determine flow paths through petroleum reservoirs that have natural fracture systems and for which water injection has been selected as the stimulative production method. A field test was made to prove the techniques and evaluate instrumentation. The feasibility of applying the techniques and instruments to the solution of reservoir problems in other stimulative methods of production also is discussed. Oil commonly is displaced from sandstone host rocks by the action of a driving force that causes the oil to move through interstices of the rock and into production wells. In addition to the requirements of oil being trapped within the sand pores and the presence of an effective displacement mechanism, the rock itself must have adequate permeability to permit flow of oil and other fluids.

Jan 1, 1961

By John Durkin

A computer model has been generated to evaluate speech intelligibility of individuals wearing conventional and electronic hearing protectors. For speakers talking at normal levels in noise levels of 65 db(Lp) or less, it was found that conventional hearing protectors significantly reduced speech intelligibility. Under the same conditions, electronic protectors provided scores equal to those for the unprotected individuals while providing protection from high noise levels. Therefore, electronic hearing protection is valuable in areas where high noise level is intermittent.

Jan 1, 1979

By Forrest T. Moyer

The safety record of the coal-mining industry, both anthracite and bituminous, in 1966 was improved over that of 1965 in all general measures of injury experience. The improvement was more pronounced in the anthracite industry. The total of 10,679 disabling work injuries comprised 233 fatal and 10,466 nonfatal injuries, 26 and 692 fewer, respectively, than in 1965. The number of fatalities in 1966 was the lowest annual total since complete records were started in 1910. Similarly, the number of nonfatal injuries in 1966 was lower than in any year since 1930 when such data were first collected.

Jan 1, 1969

By The Staff

"THE Wabana iron ore mines, owned and operated by the Dominion Steel and Coal Corporation, Limited, .are on Bell Island in Conception bay, on the east coast of Newfoundland. Mining began on surface in 1895 and, although open-pit work is still done on a small scale, the entire output may be considered to•be derived from extensive submarine workings. In 1958 the average daily production of hematite ore was close to 12,000 tons, almost all of which was concentrated in a heavy-media plant. SUMMARYThe character, occurrence, and extent of the submarine bedded deposits enabled early operators to meet prevailing market demands with the minimum attention paid to exploration. Mechanization of the mine and the pressure for sustained high tonnages since 1955 have emphasized the importance of an expanded exploration and development programme.A serious handicap has been the impossibility of utilizing normal diamond drilling methods to explore ore conditions in advance of mining faces. Drilling between tl1e bedded zones has been done but the major difficulty has been to delineate ore reserves in the lower bed, which has the greatest ore potential of the three mineable seams."

Jan 1, 1960

By Drupad B. Desai, C. C. Ku

INTRODUCTION The Laurens Street section of the Northwest Line of the Baltimore Region Rapid Transit System, located along Pennsylvania Avenue between Pitcher Street and North Avenue is situated in material which cannot be definitely categorized as soil or rock. However, in the area of residual soils in which these tunnels were constructed, considerable attention was required to determine the character of the ground so that the designers and the constructors could properly evaluate the behavior of the ground and plan their respective efforts accordingly. The Laurens Street sections structures consist of twin rock tunnels, station structure, traction power substation, vent shafts at both ends of the station, the midline vent shaft, and the twin mixed-face tunnels. This paper concentrates on the mixed-face tunnels which extend from Station 99+67.03 (O.B.) to Station 102+49.00 (O.B.) at the southern end of the section. Since the completion of the design of this project, the Laurens Street section has been renamed the Upton Station. (See Figures 1 and 2). SUBSURFACE INVESTIGATIONS At early stages, three preliminary studies were performed by the General Soils Consultant (Ref. 1, 2, & 3). The purpose of the first study was to ascertain the generalized geological and subsurface conditions which might be encountered in the region. No borings were performed for this study. A limited number of test borings were performed for the second study, which included subsurface data for the Northwest and South Lines of the Transit System. Three borings were

Jan 1, 1981

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By Gary L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from low-grade domestic chromites, which contain silicon and aluminum impurity levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten sodium hydroxide (NaOH) under oxidizing conditions to form sodium chromate (Na2Cr04). The reaction product is leached with methanol to remove the majority of the unreacted sodium hydroxide, then with water to remove the sodium chromate and the remainder of the sodium hydroxide. The sodium chromate product is recovered by evaporative crystallization from the aqueous solution. This report presents results of laboratory tests to determine the optimum fusion conditions and the chromium extractions obtained from several domestic chrotdte concentrates. These concentrates are from a variety of sources, including the Stillwater Complex in Montana, Kanuti River-Caribou Mountain, Red Bluff Bay, Kenai Peninsula, and Kodiak Island areas in Alaska, deposits in northern California, and a nickel-cobalt laterite from southern Oregon. All of these concentrates were successfully treated by the Bureau procedure. The best chromium extrac-tions obtained for each of these materials ranged from 69.5 to 98.9 pet.

Jan 1, 1985

By Lane, K. S.

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse.

Jan 1, 1969

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By David P. Lindroth

The objective of this research by the Bureau of Mines was to determine the technical feasibility and associated pilot data for drying minus 1/4-in coal with microwave energy at a frequency of 2.45 GHz. The drying data were obtained experimentally on three coal types: bituminous, subbituminous, and lignite. The experiments were performed with a custom-designed conveyorized microwave oven having a continuous power capability of 12 kW. Drying efficiencies near the theoretical maximum of 1.54 kg of water per kilowatt hour of energy input were achieved for two coals and two sizes; overall drying efficiencies averaged 77 pct.

Jan 1, 1986

By J. J. Barakso, C. Tarnocai

This paper outlines a method of testing for the mercury content of rocks, soils and plants. Techniques of sample collecting are described and the analytical procedures outlined. Examples are given of mercury determinations in two known mineralized areas in British Columbia - Copper Mountain Mines and Pacific Nickel Mines.

Jan 1, 1970

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By Nan C. Jensen, Oliver Bowles

"INTRODUCTION Limestone (which consists essentially of calcium carbonate) and dolomite (calcium magnesium carbonate) occur widely in the United States. Their presence is of vast economic importance, because they are used much more extensively than any other form of rock. In 1945, limestone (which, broadly, includes dolomite) was quarried in every State except Delaware, New Hampshire, North Dakota, and Rhode Island, and also in Hawaii and Puerto Rico. Total production (including that used in cement and lime manufacture) exceeded 151,700,000 tons, or 79 percent of the quantity of all kinds of stone sold or used during that year.Important well-known uses of limestone are as concrete aggregate, road material, railroad ballast, for liming the land, for cement manufacture, as riprap for shore protection, harbor work, and spillways at dams, and as building stone.. None of these uses, however, are considered herein. The purpose of this paper is to discuss the industrial and chemical uses that are less widely known and yet are of tremendous importance in a great variety of processing industries. Important examples are dolomite as a refractory furnace lining and limestone as a fluxing agent in blast furnaces, and as a raw material employed in sugar, paper, glass, and alkali manufacture.PRIOR REPORTIn May 1941, the Bureau issued a report 4/ that described these uses in some detail. As new and important developments have taken place during the ensuing years, a revision and representation of the salient features of these uses seem desirable. Asphalt filler and mineral wool uses included in the earlier report are omitted from this paper because they are identified more closely with the highway and building industries, respectively, than with the industrial applications."

May 1, 1947

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By T. Nagano

Mitsubishi Metal Corporation started the development work of a new process for continuous production of copper in 1961. After a series of experimental and semi-commercial operations, the first commercial plant of the Mitsubishi Continuous Copper Smelting and Converting Process was put into operation in March, 1974. The new plant, which has a design capacity of 4,000 metric ton copper per month, was built within the premises of Naoshima Smelter, replacing the old No.1 reverberatory smelter there. The SO2-rich exhaust gas from this new plant is blended with the off-gas of the No.2 reverberatory furnace for production of sulfuric acid and the overall emission of sulfur at Naoshima has been greatly reduced. The operation of the continuous plant has been satisfactory and several advantageous features of the Mitsubishi Process have been proven on a commercial scale. This paper first gives a brief description of the history of the development work and the characteristic features of the process. The paper then describes the new commercial plant and operating data obtained so far.

Jan 1, 1976

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By William F. Hahn

The Bureau of Mines recognized the problems encountered in low seam mining illumination systems. It was determined that the best way of implementing an illumination system is to integrate the design during the design and fabrication of new machinery at the factory. The purpose of this program was to integrate an approved lighting system in a low seam battery powered scoop and evaluate its performance. This report documents the work performed on this program and the results obtained.

Jan 1, 1980

By O. E. KEOUGH

AT the Tooele custom lead-zinc ore concentrator,' two sections, each having a daily capacity of 500 to 600 tons, are operated on slightly different types of ores with but little difference in flow sheet and reagents. The ores comprising the two general classes are the coarsely crystalline type, with low pyrite and sphalerite low in iron content, from the Park City district, and the more finely disseminated higher pyrite ores from Bingham, which are more difficult to treat by flotation. Laboratory testing determines with which general class a new ore will work better. The ores are crushed to minus 1 1/4-in. size at either the Utah Ore Sampling Company's plant at Murray, Utah, the Tooele smelter sampling plant, or the crushing plant at the concentrator. The ores for each section are mixed to maintain as nearly as possible uniform lead and zinc contents.

Jan 1, 1930