Search Documents

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

By M. Bouchard, B. Cadieux et F. Goutier

Five phases of ice movement were r es pons ible f or glacial dispersion in t he study area. I ce fl ow directi on changed prog r es s ively from SE to SSW and then to the S. All observed glacial sed iments are associated with a south-southwest to south movement; t hey are grouped, on the basis of their texture, structure, morphology and composition, into four distinct lithofacies. A lithological study of the coarse-grained fraction (4-128 mm) of these lithofacies shows systematic compositional differences. These are: 1) variations in the proportions of local bed rock fragments; 2) variations in the horizontal displacement of the maximum abundance peak of a given lithology relative to its source area, and 3) variations in the length of dispersion trains associated with each lithofacies. Although dispersal trains can obviously be mapped without differentiating li thofacies, studies based on the consideration of lithofacies should give more reliable results than conventional methods.

Jan 1, 1984

At Appin colliery, geological structural analyses and investigations of roof conditions suggest roof failure may be attributed to vectorial stresses acting on underground openings, and inducing movement along inherent discontinuities in the surrounding rocks. Certain complex joint and fracture patterns tend to exhibit the effect of this movement resulting often in local deterioration in natural support.The following conclusions are drawn.1. Roof failure is related to the inherent nature of the roof rocks, the presence of mechanical discontinuities, and the vectorial stresses imposed upon it.2. Roof failure is not necessarily related to the statistically most prominent jointing.3. Colliery development approximately parallel to the direction of the statistically most prominent jointing sometimes results in favourable roof conditions.4. The maximum principal stress is the resultant of those vectorial stresses acting upon a mine opening and may be inferred from roof adjustments to those stresses after mining.5. Statistical analyses of jointing in the mine workings can provide clues to the tectonic force or forces which have been regionally or locally influential.6. There is a probable relationship between mining induced fracturing, jointing, and micro-fractures in quartz grains, within the sediments of the mine roof.

Jan 1, 1970

By Spooner H. W

The paper describes the search for mineral deposits in an area of 4,500 sq. miles of south-west Tasmania. The area is one of difficult access and the problem of speedy movement and maintenance of field parties was solved by the use of helicopters. The programme has followed a systematic pattern of the aerial photography of the exploration area with the preparation of photQmosaics and topographical base sheets from these mosaics. Geological maps were initially prepared by photogeological interpretation and making use where possible of pre-existing information. The maps produced were later checked by ground traverses. Geophysical maps were obtained by the use of airborne magnetic, electromagnetic and radiometric methods. Geophysical and geological anomalies were checked on the ground by a campaign using ground geophysical equipment in the former case and geological and geochemical work in both instances. Audio Frequency Magnetic and Induced Polarization techniques were used in an area which was covered by several hundred feet of Tertiary sediments.The campaign has reached the stage of the drilling of specific targets.INTRODUCTIONThis paper describes the activities of Lyell-E.Z. Explorations (L.E.E.), an organization which was formed in 1956 by the Mt. Lyell Mining and Railway Co. Ltd. and the Electrolytic Zinc Co. of Australasia Ltd. to explore for mineral deposits in an area of approximately 4,500 sq. miles in southwest and southern Tasmania. To provide the necessary personnel and equipment for this project the exploration resources of both Companies were pooled and augmented and a headquarters was established in Queenstown. The work was directed by a Committee of four made up of officials from both Companies; a review of this structure has recently been presented by Hall (1959).

Jan 1, 1960

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Feb 24, 1997

By Anna Sukhanova, Svetlana Babaeva, Sergey Andreev, Victor Beltenev

"The Zenith-Victoria /1/ and Jubileynoye /2/ hydrothermal fields have symmetrical structural position on the Mid Atlantic Ridge (Fig. 1). In order to compare the evolution of hydrothermal systems, we conducted mineralogical and geochemical studies of SMS from both sites.Radiochemical and geochemical investigations of massive sulfides of the Zenith-Victoria field distinguishes three major stages of evolution: initial, interim and final represented by Fe-S, Cu-Fe and Zn-Fe types of SMS respectively /3/. In this talk, we describe the results of geochemical analysis of massive sulfides from the Zenith-Victoria field. Geochemical varieties of SMS are considered to be indicators of the evolutionary stages of the hydrothermal system."

Sep 1, 2014

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By R S. Hamilton, S R. Grobler, M E. Greenway

The progressive development of underground mines frequently requires increased ventilation flow rates through mine shafts that were originally designed for lower rates. Where these shafts are equipped with conveyances running on rope guides, the higher air flow rates adversely affect the lateral motion of conveyances and could cause conveyances to collide with the shaft walls or with one another. Hence the safety impact of higher flow rates requires proper assessment. This can be undertaken by use of computer simulation models to predict the dynamic motion of the conveyances during hoisting. It can also be undertaken entirely by field testing, or using a combination of simulation and field testing. This paper discusses these techniques and makes cautionary remarks about setting an absolute generic maximum flow velocity for all shafts. Approaches to assess existing shafts for increased ventilation flow rates are also discussed.CITATION:Greenway, M E, Grobler, S R and Hamilton, R S, 2017. Safety impact of increased shaft ventilation on rope guided conveyances, in Proceedings Australian Mine Vent Conference 2017, pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

By James R. Wait

The present final report constitutes the total productivity of a series of contracts from the U.S. Bureau of Mines and the Institute for Telecommunication Sciences over the period 1971-1979. The emphasis on the research has been analytical. In this "executive summary" we give a succinct description of each phase of the investigation. In the first phase of the investigation that was stimulated by the National Academy of Engineering, we concentrated on the analytical studies of techniques relevant to mine rescue. Several specific procedures for locating a buried source were analyzed. In the next, but overlapping phase of the investigation, we dealt with the fundemental character of how electromagnetic waves propagate in mine tunnels. At the outset we allowed for the finite conductivity of the tunnel walls and the presence of axial conductors such as cables, pipes, and tracks. The third phase of the investigation was devoted to the analyses of various specific geophysical engineering problems. The related fourth phase dealt with the general subject of non-destructive testing of wire ropes such as used for mine hoists.

Jan 1, 1980

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By N. Kanarin

A thermodynamic study is reported on the chlorination of Fe(1-x.)O, Fe2O3, Cr2O3, MgO, Mg2SiO4 with chlorine in the presence or the absence of reducing atmospheres. The reactivities of these compounds as well as that of Mg3Si2O5(OH)4 using Cl2+N2, Cl2+air, and Cl2+CO gas mixtures were studied by non isothermal thermogravimetric analysis between 20 and 1000 °C. The same solids were chlorinated in a horizontal experimental set, during two hours between 350 and 1000 °C, in reducing and oxidizing atmospheres: The chlorination products were examined by XRD and SEM, and possible reaction paths were examined. Results indicate that the carbochlorination of these solids was better than their chlorination; Furthermore, the carbochlorination was performed at lower temperatures than those of the chlorination. Finally, the reaction extent was higher in the case of carbo-chlorination of these compounds. Based on these results, a process was suggested for the selective recovery of chromium compounds from the chromite concentrate.

Jan 1, 1995

By A. Engelbrecht, B. North, B. Oboirien

"There is large electricity generation potential in discard coal, both in stockpiles and current arisings. Power stations with a combined capacity of up to 18 GW electrical (GWe) could be fuelled by discard coal. Modern circulating fluidized bed combustion (CFBC) boilers, with capital costs comparable to equivalent pulverized fuel (PF) boilers, are capable of utilizing discard coal at a high efficiency while reducing sulphur dioxide (SO2) emissions though the use of limestone sorbent for ‘in-situ’ capture.A detailed economic assessment of the feasibility of electricity generation from discard coal, comprising material and energy balances and the construction of a discounted cash flow (DCF) table, shows that it is also potentially attractive from an economic perspective. A base case analysis shows positive net present values (NPVs) and an internal rate of return (IRR) of 21.4%. Sensitivity analyses on critical parameters show that the economic viability is heavily dependent on parameters such as coal cost and the value of electricity. The project becomes unattractive above a coal price of approximately R300 per ton and at an electricity value below approximately 59c per kilowatt-hour (kWh).Site- and project-specific information such as the delivered cost of coal, location and efficacy of sorbents, and effective value of the electricity produced can be used as input to the economic analysis to evaluate siting options and sorbent source options for such a power station."

Jan 1, 2015

OFS Branch Committee Meeting held in the Committee Room at the Welkom Club at 4.15 p.m. on Wednesday, 5th March, 1975. Progress in mineral dressing The National Institute for Metallurgy and the South African Institute of Mining and Metallurgy are to hold a symposium on 17th and 18th September, 1975, entitled 'Recent Progress in Mineral Dressing'. INFACON 74 This book of over 300 pages is a record of the First International Ferro-alloys Congress, which was held in Johannesburg from 22nd to 26th April, 1974, under the auspices of the Ferro Alloy Producers' Association of South Africa, the National Institute for Metallurgy, and the South African Institute of Mining and Metallurgy. NIM reports Report no. 1595 Preliminary tests on low-grade brecciated fluorspar ore from the Ottoshoop district. (5th Nov., 1973, declassified April 1975). Report no. 1612 Flotation tests on sulphide-bearing high-grade brecciated and wad ores. (20th Mar., 1974, declasl>ified April 1975). Report no. 1643 Further tests on low-grade brecciated fluorspar ore from the Ottoshoop district. (12th Jul., 1974, declassified April 1975). Report no. 1654 The determination of osmium in platiniferous media. Report no. 1689 The determination, by atomicabsorption spectrophotometry, of arsenic, selenium, tellurium, antimony, and bismuth on ion-exchange restns. Report no. 1715 Flotation tests on various types of ore from the Ottoshoop district Report no. 1730 The chromitite from the Marico occurrence, western Transvaal, its alteration, and possible reasons for its refractory nature. Report no. 233 A chemical and mineralogical study of microlite from the N oumas pegmatite. 24th Geomechanics Colloquy The above Colloquy is to be held on 2nd and 3rd October, 1975, in the Salzburg Congress Hall. Rosenhain centenary The centenary of the birth of WaIter Rosenhain (1875-1934) will be celebrated by an international conference to consider how physical metallurgy has contributed to engineering practice. Iron and steelmaking The Centre de Recherches Metallurgiques (CRM) and the Verein Deutscher Eisenhiittenleute (VDEh) are jointly to hold the International Meeting on Iron and Steelmaking 1976 in Brussels from 17th to 18th May and in Diisseldorf from 20th to 21st May, 1976. International Symposium on Mine Surveying The III I.S.M. is being held in Leoben, Austria, from 28th June to 3rd July, 1976. Book review Tenth International Mineral Processing Congress. 1973. London, The Institution of Mining and Metallurgy. 1208 pp. £20. Particles A course on particle characterization and a symposium on experience in the applications of particlesize analysis will be held during the last week of July in Pretoria and Johannesburg. A.S. & T.S. Trust The A.S. & T.S. Trust was formed on 24th March, 1972, to mark the Golden Jubilee year ofthe Associated Scientific and Technical Societies, with the object of advancing science and technology in South Africa. Second International Congress of Engineering Geology The Proceedings of the above Congress, which was held in Sao Paulo, Brazil, from 18th to 24th August, 1974, are now available.

Jan 6, 1975

By Ralph P. Hackl

Ore at the Congress gold property, located near Goldbridge, British Columbia, is extremely refractory with most of the gold disseminated in fine-grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225m' (7950-cu ft) commercial size bioleach reactor was built and tested at the mine site in 1989. At that time, the tank was the largest bioleach reactor ever operated. The objectives of the program were: • to ascertain if the biooxidation rates obtained in lab and pilot-scale reactors could be duplicated in a commercial scale tank; • to identify agitation conditions under which the process will function optimally; and • to demonstrate the bioleach process on a scale sufficient to satisfy the owners and potential investors.

Jan 1, 1990

By P Mulvey

"Currently mine process studies and geochemical waste characterisation are considered as two interdependent studies, necessary for the development of the mine and inclusion in the environmental impact statement (EIS). Geochemical waste characterisation will utilise the simulated tailings produced by the mine process studies team to understand the behaviour of the tailings, but the two teams rarely integrate these to develop a coherent and agreed final design.Thorough mine waste geochemical assessments can develop processes to minimise environmental harm, resulting in substantial savings in the decommissioning, closure and rehabilitation phases, and may also be able to address changes in mineral processing methods that can result in substantial savings in process inputs, or even recovery of metal concentrates.Based on geochemical waste characterisation, the full cost of waste management can be calculated and incorporated into the costing of milling.  This allows for a more effective evaluation of the metallurgy.  A number of examples are presented in which substantial improvements have been made from the collaboration of both the metallurgical and geochemical teams during planning and the metallurgical team and environmental team during operations.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Optimising metallurgy at the planning stage to minimise environmental impact - a feedback loop from geochemical waste characterisation, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Shimi Tzobery, John E. Shamma, Samuel Swartz, Gary B. Hemphill

The trapezoidal tapered ring method has made significant progress in recent years for shielded-TBM projects, excavating tunnels with high overburden, strict water tightness criteria, and multiple curve alignments. The selection of compatible tapered rings is critical for successful advancement of the tunnel, assuring efficient installation of rings, as well as prevention of ring damage and excessive leakage. Using experience from the Arrowhead Tunnels Project, this paper describes guidelines for ring selection in tunnel curves, geometric analyses that comply with criteria principals, and provides techniques developed to determine the appropriate relative key position.

Jan 1, 2005

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007