Search Documents

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By K. Tangri, M. Chaturvedi

On water-quenching from within the (a + ß) phase region Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys can undergo w transfirmation. This transformation has been attributed to the enrichment of ß Zr phase, at the solution-treatment temperature, by the solute atoms. The ß—w transformation is accompanied by a hardening 01 the alloys and in the optimum condition w-bearing specimens of the ternary alloy are about 14 pct harder than those bearing only a' phase. On aging crl reverls thermally to more stable phases, which results in a considerable softening of the specirnens, as follows: w quenched -waged + ß Zr (enriched) waged - a + ß Nb The high-temperature bcc ß Zr in certain zirconium alloys can transform to a metastable w phase which has a primitive hexagonal structure. In the Zr-Nb alloy system w phase has been observed in the composition range of 7 to 15 wt pct Nb by a number of investigators.'-' In this composition range w can form by water-quenching ß Zr or by aging. known as athermal and thermal w, respectively. Hatt and Roberts' have found that thermal w has a constant c/a ratio of 0.622 +0.002 regardless of the composition and tha: the lattice parameters are of the order of a = 5.02A and c = 3.0 ?. The actual lattice parameters depend upon composition and the temperature of aging. The lattice constants of athermal w. however, depend upon alloy composition.3 The presence of w phase in zirconium alloys can cause substantial strengthening which has been attributed as probably due to the coherency between w and parent ß Zr phase. Robinson et al.' found that the presence of w can raise the strength of Zr-5.0 Nb-2.0 Sn and Zr-5.0 Mo-2.0 Sn alloys to about 170.000 psi: however. the ductility is considerably reduced. With the growing use of Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys in the nuclear reactors, and the significant effect of w transformation on the mechanical properties of zirconium alloys studies were undertaken to study the w transformation in Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys. This paper is concerned with the formation and reversion of w phase in these alloys. 1) MATERIALS AND EXPERIMENTAL TECHNIQUES The following two alloys were studied: 1) Zr-2.5 Nb-0.5 Cu (referred to as the ternary alloy): 2) Zr-2.5 Nb (referred to as the binary alloy). The chemical analysis of the alloys is given in Table I. The alloys, in the form of 3/8-in.-diam rods and 1/8-in.-thick sheets, were supplied by the Chalk River Nuclear Laboratories of the A.E.C.L. Initial fabrication for preparation of various specimens was carried out by cold rolling and swaging with intermediate anneals at 1000°C. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-% m of Hg. For optical metallography and hardness measurements disc specimens + in. diam by + in. thick were used. After the required heat treatments the specimens were mechanically and then chemically polished in a 45 pct HNO3, 45 pct H20. and 10 pct HF solution. The hardness measurements on the chemically polished specimens were carried out on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative hardness value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using copper K-a radiations in 114.6-mm-diam camera. Thin films for transmission electron microscopy were prepared by electropolishing heat-treated a by 7 by 0.005-in.-thick strips using a modified Bollmann-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol electropolishing bath was kepl at -5OCC and polishing was done at 5 to 10 v. The thinned specimens were washed in ethyl alcohol at -30" to -40°C and dried between filter papers. The thin films

Jan 1, 1970

By Luiz Filipe Cardoso de Oliveira, Alex Milton Albergaria Campos, Paulo Santos Assis

Em usinas siderúrgicas integradas a coque, o carvão mineral tem papel fundamental principalmente na produção de coque metalúrgico, que será utilizado nos altos-fornos para produção do ferro-gusa. O coque é produzido a partir de misturas, de carvões minerais com diferentes propriedades, formuladas para atender os requisitos operacionais do processo de coqueificação e a garantir a qualidade do ferro-gusa que será produzido nos altos-fornos. Além disso, está mistura deve ter o menor custo possível uma vez que a maior parte do carvão metalúrgico utilizado no Brasil é importado, representando assim uma grande parcela do custo do aço. O grande desafio do setor é obter misturas de carvões que atendam a coqueria e produzam coque com alta qualidade e baixo custo. Para tanto, é necessário uma otimização de vários processos, desde a compra e transporte do carvão até sua estocagem, formação das misturas e abastecimento da coqueria. Com isto, este trabalho vem com o objetivo de sugerir uma otimização e planejamento da mistura de carvão para a coqueria com a utilização de rejeitos plásticos de menor valor agregado na mistura que possibilitem a produção de coque com menor custo e com a qualidade exigida no processo de fabricação de aço.

Oct 1, 2019

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950's, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.'-'' These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By Júlia Guimarães Sanches

O curso de Engenharia de Minas sofreu uma expansão, juntamente com todo o ensino superior no país, por volta de 2005. O objetivo do presente estudo é avaliar as características dos cursos do país e realizar uma comparação com cursos de outros países com grande produção mineral. Foi feito um levantamento inicial a partir de informações disponíveis nos sites do MEC, INEP e das universidades. Como complemento, realizou-se um questionário com os coordenadores dos cursos de Engenharia de Minas do Brasil. Foram compilados ainda dados relativos à estrutura curricular e carga horária dos cursos de Engenharia de Minas dos EUA, Canadá, Austrália, Chile e África do Sul. Em relação à comparação das grades curriculares com os cursos de outros países, observou-se que no Brasil o curso possui uma maior cara horária de Tratamento de Minérios em detrimento da lavra. Nos demais países estudados, o foco das disciplinas é a lavra, já que nestes países a área de Tratamento de Minérios é assunto de outras Engenharias.

Oct 30, 2017

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

ALTHOUGH great progress has been made in flotation of the Broken Hill silver-lead-zinc ores, no paper dealing with this subject has been presented to the members of the Institute since James Hebbard's valuable contribution in 1913. Almost every discovery or development in the history of flotation has formed the basis 6f a patent, and but few experimentalists have overlooked the fact that their investigations might lead to the establishment of a patentable process. This, together with the aftermath of patent litigation, naturally resulted in secrecy being maintained in matters appertaining to the art, and the industry as a whole has consequently suffered considerably. Much valuable time has been wasted through numbers ofmen repeating work along certain lines, which, unknown to them, had already been thoroughly exhausted by others, whereas a lot of this would have been avoided by a freer interchange of information amongst those directly concerned. Owing to differences in the ore treated and the various applications of flotation concentration in relation to gravity methods, the flotation problems of the various mines differ considerably. This, together with the secrecy previously referred to, hasresulted in the development of numerous systems and machines, most of which would appear, to the casual observer, to comprise separate and distinct processes. The author has endeavoured to show how much these processes have in common with one another, and, at the same time, has tried to convey some general ideas on flotation to those members of the Institute who are not directly associated with this branch of concentration.

Jan 1, 1919

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2003

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By V. J. Parks, Leonard Obert, A. J. Durelli

The state of stress in the region where core discing initiates has been investigated through the use of three-dimensional photoelastic models and the results of this study have been compared with those of a previous investigation of rock models. This comparison showed that discing initiates at a point of maximum shear stress, but that the magnitude of the shear stress, as determined photoelastically, is much larger than the shear strength of the rock as deter-mined from conventional triaxial testing. Moreover the shear stress required to produce discing is not constant, but depends on the applied stress field. Possible explanations for these effects are included in this article. In both exploration core drilling and overcore drilling to determine the stress in rock, occasional sections of the core obtained are broken into a series of discs.I* This discing phenomenon has been investigated in the laboratory to ascertain the state of stress required to produce it. The objective of the study was to obtain information that would make it possible to approximate the state of stress in subsurface rock from which disced cores are obtained. Referred to as the discing test, this laboratory study was conducted to determine the applied axial and radial loads required to produce discing in cylinders of rock from several sources. The dimensions of these cylinders are given in Fig. 1. Discing was produced by first applying an axial load to the cylinder and then diamond drilling the core along its axis. The radial load was then incrementally increased until discing initiated. The discs fractured or ruptured* on surfaces approximately normal to the axis of the core (planes A, B, C, D, E, Fig. 2). In many instances, the bottommost disc fractured before the drill had advanced past the points F and F', cre- ating a mush room-shaped fracture surface FEF'. Alternatively, it was also found that the same shaped fracture surface could be created by first drilling in an unloaded core to some point, say F and F', and then triaxially loading the core until fracture occurred on the plane FEF'. Jaeger and cook4 produced similar fracture surfaces in specimens subjected only to a radial biaxial load. From these laboratory studies and observations made in the field, it can be inferred that fracture or rupture initiates in the proximity of the lowest point in the kerf area, (at F and F', Fig. 2) and that the fracture or rupture surface progresses inward from this point. The experiments described above, however, do not provide any information as to the state of stress at the point at which fracture or rupture initiates. In the investigation discussed in the following sections, a three-dimensional photoelastic analysis was conducted to determine the stress distribution in the proximity of the kerf area of a triaxially loaded plastic (epoxy) cylinder containing a short section of core.

Jan 1, 1969

By H Han, X Wang, T Li, D Duan

"In this paper, the reduction and separation behaviour of iron and slag in carbon composite iron ore pellets has been investigated experimentally using an electric resistance furnace simulating a rotary hearth furnace process. The factors that affect the formation of iron nuggets, such as temperature, holding time, molecular ratio of C/O and basicity, are discussed. Results show that the reduction of iron ore, carburisation of reduced iron and the composition and quantity of slag are very important for producing iron nuggets. Through optimisation of process parameters, iron nuggets can be formed below 1300¦C when holding time is 20 minutes, C/O is 0.7 and basicity less than 0.5. This study provides a theoretical and technical basis for iron nugget production.CITATION:Duan, D, Han, H, Wang, X and Li, T, 2013. Iron nugget production technology in rotary hearth furnace process at lower temperature, in Proceedings Iron Ore 2013, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006