Search Documents

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By D. Tolgyesi, L. P. Gignac

Mine development has evolved in the past 15 years from a human-paced system using hand-held drills and track-bound equipment to a mechanized system using specialized equipment for each component of the development cycle. In most Canadian hard-rock mines, face advance is achieved by the following sequential activities: drilling, explosive loading, mucking and ground support. The state-of-the-art for each work element is reviewed and methods for performance estimates proposed. The entire development system and its production capabilities are considered based on equipment reliabilities, spare units, haulage distances, and muck bay spacing. The effect of the number of working faces on the system's performance will also be analyzed. Manuscript not received in time for publication.

Jan 1, 1983

By Óscar Cantorín

El presente texto describe las ventajas del sistema de relleno utilizado en la compañía minera Ares de Arequipa. La metodología del relleno se inicia en el tajo de una chimenea, la cual contiene las tuberías bicapa. Luego se conecta mediante un niple las tuberías de una sola chapa, y se instalan hacia el tope del ala del tajo que entrará en relleno. Entonces, se prepara una barrera con tablas y puntales en el límite señalado para rellenar, y la parte interior se forra con tela prolipropileno. Al estar preparado el tajo, se comunica al personal de Planta de Relleno el inicio de la operación, donde se hace una mezcla de agua y cemento para lubricar la tubería. Luego se procede a bombear la mezcla con las proporciones de diseño y un slump promedio de 8 pulgadas. El tajo de 60 m de longitud, se rellena hasta en 3 etapas, ya que las tuberías son recuperadas en su totalidad y finalmente el relleno queda a 0.5 m del techo de la labor. Entre los principales beneficios de este tipo de relleno tenemos que: no tiene excedente de agua, no necesita sistema de drenaje, permite la continuidad del minado ya que no es necesario esperar más de un día para reiniciar las operaciones, recuce el costo del relleno con la disminución de cemento y prolonga la vida de la cancha de relaves.

Sep 13, 2001

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By Jalna R. Zatko

The Bureau of Mines, U.S. Department of the Interior, has developed a novel method of flocculation dewatering of phosphatic clay wastes using polyethylene oxide as the flocculant. Research was conducted to determine whether ethylene oxide gas was present in the air in the vicinity of disposed waste materials which had been flocculated with polyethylene oxide. Samples of clay waste materials containing polyethylene oxide were prepared in stoppered glass bottles in simulated disposal environments. Gaseous samples, removed over a 75-day period using an airtight syringe, were injected into a gas chromatograph that was capable of separating ethylene oxide from air. The presence of ethylene oxide gas was not detected in any sample. To determine possible degradation products of polyethylene oxide, the properties and reactions of ethylene oxide and its polymers were reviewed. Based upon the literature survey and experimental study, it was concluded that adverse environmental effects were not likely to result from the use of polyethylene oxide for flocculating phosphatic clay waste products.

Jan 1, 1980

By A G. L Pratt, M S. Kemp

BHP has used many innovative techniques when recruiting its workforce for the Cannington Project. Looking for a balance of experience and enthusiasm it was necessary to develop pre-selection tests to reduce the initial number of applicants to a manageable number for first interviews in Townsville. Success at this stage led to an applicant, and their spouse, to go through a second interview at the mine site. The full process from application to job offer took up to six months, but the results were felt to be worth the effort. The approach taken has resulted in a highly motivated and flexible workforce. This paper outlines the philosophies behind CanningtonÆs recruitment process, highlights some of the issues associated with the approach, and offers some measures of the outcomes.

Jan 1, 1998

By Frank J. Wiebelt

The Carbonate King zinc mine is on the west slope of Kokoweef Peak, Ivanpah Mountains, San Bernardino County, Calif. It has produced more-than 10,000 tons of ore with a 39-percent?zinc content since mining operations began in 1940. The ore, consisting principally of calamine and smithsonite, occurs in replacements of the YellowPine limestone. Milling, has been done from the surface to a depth of 275 feet. Eight holes, aggregating 2,121, feet were drilled by the Bureau of Mines in an endeavor to establish extensions of the worked-out ore bodies and to develop new ones. Although indication of mineralization was found in several of the holes, no new ore bodies were developed.

Jan 1, 1949

By E. D. Hummer

During the planning phase of the fine coal cleaning addition at the Gary Coal Preparation Plant, careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at 1/4 inch, pumping the minus 1/4 inch raw coal to bowl desiltors for desliming, and then cleaning the disliked raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 foot diameter thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh Today the minus 48 mesh refuse at Gary consists of thickened flotation tailings and thickened spiral classifier overflow. The transportation of large quantities of fine wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds

Jan 1, 1965

By Fred D. Wright, Stefan H. Boshkov

12.1-BASIC AND PARAMETRIC CRITERIA IN THE SELECTION, DESIGN AND DEVELOPMENT OF UNDERGROUND MINING SYSTEMS STEFAN H. BOSHKOV AND FRED D. WRIGHT The criteria governing the selection of an underground mining system relate to several factors the importance of which varies with geographic location, the state of development of the industrial technology, the economic climate in the Nation and, perhaps, in the world-all these as functions of time. Thus, the best choice of a mining method depends upon sets of definable and undefinable values for numerous factors that may be considered fixed at the precise point in time. Subsequent changes in economic and/or technological developments may necessitate modification or complete revision of the existing mining system. A classification of criteria for selecting a mining system must be based on the broadest definitions. Specific cases may present simple solutions or pose very intricate questions, the answers to which are frequently based on judgment rather than explicit logically reasoned and derived results. Specific criteria may be of negligible consequence in some instances and of overriding importance in other cases. It would be foolhardy to attempt to point out, in the limited space available, all possible variations and interplay of factors, as well as to define the setting in which this interplay can take place. The reader is, therefore, referred to the case histories described in the subsequent parts of this section where actual practice will point out the variability of the problems encountered in the selection of a mining method. A popular thesis suggests that the proper approach to selecting the method of mining should be rooted in the inverse solution, whereby the limitations of the various methods in use serve as criteria to eliminate most of these methods from consideration in the specific case. This narrows the ultimate selection to one or perhaps two most appropriate methods. At this stage, a critical comparison analysis will lead to the ultimate choice. Although such a negative approach un¬questionably is valid in discarding obviously inapplicable mining systems from consideration, it falls short in defining the best system, which in practice quite often turns out to be a variation of a textbook standard, or a combination of two or more such standards. Because the deployment of capital and manpower over a long-term commitment closely follows the selection of the mining system, the decision-maker can well afford to spend a great deal of time and effort in evolving the optimum solution for the peculiarities of his specific case. Within the basic engineering tenets of economy and safety to which the design of a mining system must adhere lie numerous factors of constraint which may be grouped, somewhat arbitrarily but for ease of discussion, into several categories. The criteria that enter into the choice of a mining method derive from the following groups of factors: 1. The shape, size and spatial position of the ore deposit.

Jan 1, 1973

By Shun-ichi Satoh

A NEW method of treating steel by ammonia has recently been intro¬duced into the metallurgical industry, by means of which piston cylinders of internal combustion engines, shafts and other similar steel products can be made more resistant to wear than formerly. In 1929 the writer' published the historical notes and some experiments upon nitrification. He believes that the corrosion of nitrified steel is a matter of importance and worth studying; and as there have been few studies thereof, he has conducted experiments in this respect. L. Guillet,2 in 1927, reported corrosion tests made on nitrified and cemented steels with acid and salt solutions. In 1928, 0. Hengstenberg3 reported the high resistance of nitrified steel to water vapor and air. V. 0. Homerberg4 stated that nitrified steel has high resistance to water, air and salt solution; and G. Hagg5 studied nitrified layers of iron by means of the X-ray. Though F. Hanaman6 in 1913, measured the single potential difference of steel treated with ammonia at above 650° C., no one, it seems, has ever measured the single potential difference of the so-called nitrified steels having extraordinary hardness. The writer measured the single potential differences of nitrified special steels in various solutions with the object of studying the corrosion problem and, if possible, of knowing whether any new physical property would be caused by nitrification.

Jan 1, 1932

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By B. H. Kear

All the possible ways of forming simple two-dislocation boundaries in multiple slip orientations are deduced. It is shown that the principal differences in work hardening behavior of crystals plastically deformed in these orientations can he accounted for in terms of the likelihood of formation of diffuse boundaries, or deformation bands, consisting of the products of dislocation reactions of the Lomer type. Also, it is pointed out that the break-up of boundaries under the applied stress is more likely to yield interstitial jogs than vacancy jogs, whereas glide dislocations cutting throuqh dislocations trapped in particularly stable boundam'es can acquire both types of jogs. USING Frank's' grain boundary formula, Ball and Hirsch2 determined the parameters of all the possible boundaries that can be built from two sets of glide dislocations in the fee structure. This paper deduces the geometrical possibilities for the formation of these two-dislocation boundaries in the different multiple slip orientations, and discusses the role of boundaries in work hardening and in jog formation. Formation of Two-Dislocation Boundaries in Mutiple Slip Orientations. The parameters of the possible two-dislocation boundaries for any crystal orientation can be deduced most conveniently using the boundary formulae due to Amelinckx,3 in conjunction with the stereographic projection shown in Fig. 1. Suppose that slip occurs in a-BC and ß-CA. According to Amelinckx, when the two systems of glide dislocations are parallel, the rotation axis, u, of the boundary is parallel to (a x ß) and the unit normal, u, defining the boundary plane is parallel to (a x ß) x (BC x CA). On the other hand, when the glide dislocations form a crossed grid, u is parallel to (BC x CA) and u is parallel to (a x CA) x (ß x BC). In Fig. 1, (a x ß) is the pole of the great circle passing through a and ß, so that u is parallel to DC, i.e., parallel to [110]. Furthermore, (a x ß) x (BC x CA) is the pole of the great circle passing through DC and 6, so that u is parallel to [110]. Hence, when all the glide dislocations are parallel, the boundary is pure tilt with parameters u = [110], v = [ 110]. Similarly, it may be shown that the corresponding crossed grid of dislocations is a mixed boundary with u = [111], u = [111]. Consider the case of a crystal compressed in the [001] orientation. In this orientation, according to Fig. 1, there are eight available slip systems. In what follows, the different types of two-dislocation boundaries that are possible in this orientation will be examined by taking different combinations of two slip systems out of the available eight, with a-BC always one of the systems. Case (i)—Slip Systems a-BC and d-CB. The formation of a tilt boundary in (101), which consists of a crossed grid of edge dislocations with vectors BC andCB, is illustrated in Fig. 2(a). As the figure shows, slip is required in the system a-BC in one part of the crystal and in d-CB in the other part, with both sets of dislocations entering the boundary from opposite sides. The rotation axis of the boundary lies in (101), depending on the relative densities of the two sets of edge dislocations in the boundary. Case (ii)-Slip Systems a-BC and ß-CA. The two possible boundaries are shown in Figs. 2(b) and (c); boundary (b) is tilt with u = [110], u = [110], and

Jan 1, 1962

By Charles B. Manula

Judging from the rapid pace of increased demands for mineral products, technological forecasting will become an increasingly necessary tool in mining. Even though the mining industry in 1966 produced more are than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. If metal and mineral commodities continue to hold their respective and present share of markets, the prospect of coping with demands from a population that will double in the next thirty years can become an impossible task when viewed outside the limits of technological advance and change. Those mining companies that are doing little to develop new and expanding horizons for their operations cannot expect to survive. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which, consequently, has resulted in some spectacular developments. Already production rates at many places are dwarfing those of the Panama Canal and other well-known earth moving projects which are frequently identified as massive undertakings. With projects of this scale, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process.

Jan 1, 1968

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By Adrien Berton

FOR nearly a century, the Corocoro deposit has been renowned among geologists from the fact that it shares with the Lake Superior deposits of the United States the distinction of being the only important copper districts where native copper is worked commercially. The Corocoro district, named after the city of Corocoro, the capital of the Province of Pacajes (Department of La Paz, Bolivia) is situated towards the western edge of the Bolivian high plateau, at an altitude of a little over 13,000 ft. The most interesting part of the district is that immediately surrounding the city of Corocoro, at a distance, by railway, of 65 miles from La Paz and 210 miles to the Chilean port of Arica on the Pacific Coast. The climate of the region is that of the semi-desert, dry and relatively cold, with big differences of temperature between day and night. The rainy season begins in December and ends in March. The cupriferous lodes of Corocoro have not attracted as much interest as the silver mines of Potosi but they have been known for a long time. In the precolonial period the Indians were using the charquis, or natural native copper sheets, to make small brass objects, and the beautiful pale green brochantite of the outcrops as a source of green pigments. During the colonial period, the oxidized ores of the outcrops were worked for copper, which was used by the mint at Potosi for making currency. The native copper ores were neglected because the Spanish miners were at a loss how to concentrate and smelt them. About 1830, work by rudimentary processes, which were improved little by little, was begun on the native copper ores. The total production of native copper in the following hundred years amounted to 100,000 tons. This native copper, which was remarkably pure, was much appreciated on the European markets before the introduction of electrolytic copper. It was useful for making special ornamental brass or bronze and the granular concentrates of native copper, called barrilla, containing 80 to 85 per cent copper were suitable for making copper sulfate by direct oxidation and subsequent leaching with sulfuric acid.

Jan 1, 1936

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992