Search Documents

By Edward W. Parker

IF one is to place any credence at all in the reports published in the daily press, the subject of conservation has been a very lively topic of conversation during the past 60 days, and it does not appear that the temperature of the summer months has been in any way moderated by the discussion. It is a subject in which we are all vitally interested and to which, so far as our mineral resources are concerned, both the Institute and the Geological Survey have liberally contributed. The report of the National Conservation Commission, appointed by President Roosevelt, contains a series of papers on the conservation of mineral resources, all of which were prepared by members of the Geological Survey and were compiled largely from information previously collected by that Federal bureau in the performance of its regular duties. It is not the purpose of this paper to reiterate in extenso any of the material already published. The contributions of the Survey officials to the Commission's report have been published in a separate document as Bulletin No. 394. This docunient is for free distribution and may be obtained upon application to the Director of the Survey. In the preparation of this paper I desire merely to make a few suggestions regarding the possible necessity of some restraint upon or control of one branch of the mining industry with which I have been somewhat closely associated for the past 20 years-that of coal. Most of the members of the Institute are cognizant of the suits brought by the government against the anthracite-operators in Pennsylvania, or the combination of interests commonly known as the ? hard-coal trust." No defense of any illegal combination in restraint of trade is intended, but there are some facts which should not be lost sight of, and unfortu-\

Nov 1, 1909

By M. A. Llavona

In Spain, as in many countries, the gold content of jewellery must be officially hallmarked. The official methods of assay are gravimetnc cupellation (a method which is highly accurate but both time and sample consuming), potentiometry, gravimetry and volumetry. In this paper, a procedure for measuring gold by flame atomic absorption in jewellery samples is described. The method is based on the acid digestion of a 40 mg sample. The quantity of aqua regia necessary for dissolving the gold, the ideal weight of a sample in order that the error may be minimal, the effect of the acids employed, the type of material used for its storage, and the necessity of employing a buffer to avoid the ionization of the solution are described. The method proposed is simple, highly accurate and causes little damage to the jewellery.

Jan 1, 1999

By Roberto Folchi

"This article deals with the excavation of a tunnel below the town of Isola LIRI, nearFrosinone, in central Italy. The tunnel was driven into a conglomerate formation, of lacustrine_fluvial origins, consisting in carbonate clasts with a sandy_silty matrix and calcitic cement. ""Drilling andblasting"" had to be adopted in place of a tunnel boring machine which had showeduneconomical performances. Good advance speed rates were achieved notwithstanding thepresence of some above structures to safeguard. The nearest structure (an old votivechapel) was less than 10 meters (33 ft.) far from the tunnel crown; the nearest residentialstructure was at about 15 m (49 ft.)."

Jan 1, 1993

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By K. R. Brown, P. L. Krawchuk

In-situ recovery (ISR) is under increased investigation as a viable methodology for the extraction of minerals in ore bodies that may be uneconomic to mine by traditional methods or for resources situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash and uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. ISR allows for the extraction of metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in a process that produces very little to no waste rock or tailings. This paper aims to discuss the geological conditions that make ISR amenable to an ore body as well as the application of maturing technologies such as advanced directional drilling and the creation of artificial permeability that will help to access deep ore bodies and enhance or create favorable recovery conditions for ISR in the ore body. INTRODUCTION In-situ recovery (ISR), also referred to as in-situ leaching, is a potentially disruptive technology for the mining industry. ISR is under increased investigation as a viable methodology for the extraction of valuable minerals that may be uneconomic to mine by traditional methods or for deposits situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash mining, uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. Recently there has been increased interest in deploying ISR in hard rock applications due to a number of factors: the drive for environmental stewardship is stronger than ever, technological advances in drilling, blasting, and leaching are strengthening ISR economics, and a large inventory of ore bodies exists that are not feasible to mine or extract using conventional open pit or underground mining techniques. ISR allows for the extraction of valuable metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in solution via a recovery process that produces very little to no waste rock or tailings. Where the right conditions exist, the ISR process has a much smaller environmental footprint (Hiam-Galvez, 2018) and potentially much lower capital and operating costs than using conventional mining techniques.

Jan 1, 2019

By Elif Çevik

This study deals with the mineralogical-geochemical characteristics and the industrial usage of the olivine from the dunites that crop out on the west of the Topuk village (Orhaneli). Mineralogical compositions of non-altered dunite samples are averagely as: Olivine (>90%), serpentine (1-4 %), opaque minerals especially chromite, magnetite, pyrite (1-3 %), and secondary minerals as magnesite, chlorite (1-2 %). X-Ray Diffractograms of the dunite samples indicate that olivines are in forsterite (93 on an average) composition, and chlinochrysotile and lizardite accompany to the forsterite. Chemical analyses of the dunites show that MgO, SiO2, Fe-,03 and LOI contents vary from 40,99 to 50,2 %, 34,67 to 40,6 %, 6,8 tol3,7 %, 0,11 to 11,27 %, respectively. SE-TAT Mining Company states that the study area has 400.000.000 tonnes proved, 800.000.000 tonnes probable and totally 1.200.000.000 tonnes olivine reserve. Consequently, all studies indicate that Orhaneli Olivin has convenient mineralogical and chemical properties and the grain size (0.04-40 mm) for industrial usages such as abrasive, olivine sand products, steel slag conditioner, balast and covering material in industry: Orhaneli olivines are demanded especially from the firms related to refractory industry, iron-steel factories, naval forces and shipyards. SE-TAT Mining Company also exports these olivines to different countries such as Macedonian and Spain.

Jan 1, 2005

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors' project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant's design output level.

Jan 1, 2011

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By Jurgens PE Hamman, Faisal Putra, Hadnaltias Alpeki, Willem de Beer

The Deep Ore Zone mine is the third lift of caving at PT Freeport Indonesia’s East Ertsberg Skarn System. An increasing trend in seismicity along the northern boundary of the DOZ cave, as well as the northern fringes of the DOZ production and infrastructure levels, was taken as indicative of an interaction between the approaching DMLZ cave and the DOZ subsidence zone. Seismicity trends and locations indicated a reducing crown pillar and an associated stress increase along these DOZ excavations, as well as the regional area along the DOZ cave boundaries. Although rockbursts were not identified as an immediate hazard, seismic shakedown was a highly probable hazard in the case of remote large (≥3.0) seismic events. An evaluation process, as described in the Canadian Rockburst Support Handbook (1996), was followed to identify and quantify the various parameters that could contribute to a shakedown evaluation. A shakedown assessment, based on the Peak Particle Velocities scaling relation, was conducted to assess the current installed ground support systems along the northern fringes and the fixed facilities of the DOZ mine. The range in ground support systems were mostly due to different geotechnical environments. The load–deformation characteristics of these support systems were evaluated to determine the support capacity and compared to the potential support demand under varying shakedown conditions. Shakedown hazard maps were compiled to indicate the installed ground support system’s vulnerability to seismic shaking. Based on this information, areas were divided into zones indicating whether they were sufficiently supported, additional support was required, access was to be restricted, and / or they were to be abandoned. Mine management utilised these hazard maps to strategize actions for the various operational zones within the DOZ, including the fixed facilities. This paper briefly describes the derivation of the PPV scaling relationship. Seismic and geological data for the DMLZ – DOZ interaction areas were evaluated to determine the likely source of large events. Subsequent larger events and their effects are shown to assess the veracity of the magnitude and PPV estimates, as well as the effectiveness and appropriateness of the ground support systems.

Apr 26, 2022

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

Pasminco is actively addressing the optimal utilisation of the known orebody at the Broken Hill mine, in addition to actively exploring for economic mineralisation in the region. As part of the policy of better utilising the known mineralisation a major upgrade of geological systems at the mine was initiated. The software chosen for this change was Maptek's Vulcan, mainly because of the ease of use of this package. Rather than having numerous data sources in varying software packages the mine aimed to limit interfaces and packages. The decision to upgrade the mine's software was not taken lightly, especially in view of the inature stage of Broken Hill mining operations. However, the current mine life of Pasminco Broken Hill mine is I I years, which is longer than many new mines setting up in Australia today. Also, a more sophisticated system brings with it a better understanding of the economic mineralisation, possibly extending the mine life further. The process of moving the Broken Hill databases into Vulcan was a huge task which included, database transfer, digitising, wire framing, modelling and eventually ore resource calculation. To ensure the validity of the new ore resource accounting system, the existing system was run as a duplicate for the introductory year, providing a comparison and if necessary a safety net. The benefits of such a change, however, became apparent almost immediately. Area geologists realised the opportunity to revise geological interpretations in their areas of responsibility, enabling them to obtain a better understanding of orebody morphology. Three- diniensional analysis provides an excellent method by which review of ore targets both in the underground and mine lease exploration areas can he made. As each new find of mineralisation enters the system and hopefully extends the mine life, the opportunities for further mineral exploration in Broken Hill area by Pasminco are enhanced.

Jan 1, 1997

The Institute has no available copies of Bulletin No. 7, January, 1906, and Bulletin No. 105, September, 191.5. The sum of 30.50 per copy will be paid for these Bulletins.

Jan 6, 1917

PORPHYRY mining in the Bisbee district in Arizona did not begin until 1923, though Bisbee had been the scene of profitable copper-mining operations since 1880, and during the interval had contributed roughly 2,000,000,000 lb. of copper to the world's supply. At that time it ranked third among the copper districts of the United States, first place for total production going to Butte, Montana, and second to the district centering around Calumet, Michigan. Bisbee's production had come from the so-called "limestone" mines operated principally by the Phelps Dodge Corporation and the Calumet & Arizona Mining Co. Each of these companies had a large smelting plant at Douglas, 25 miles southeast of Bisbee on the Mexican border. The town of Douglas owed its existence primarily to the copper mines of Bisbee, the particular location having been determined, first, by the fact that water in adequate supply could be obtained by sinking wells; and, second, by its position about equally distant from Bisbee and the mines in Sonora, Mexico, of the Moctezuma Copper Co., a Phelps Dodge subsidiary. Three partners, Martin, Reilly, and Ballard, conducted the first operations of consequence at Bisbee about 1880; and in 1881 a smelting plant consisting of two 36 in. water-jacketed blast furnaces was erected near by. The ore came from open-cut workings on the later-to-be-famous Queen orebody. The furnace charge is said to have averaged 23 per cent copper-twice as rich as the concentrates from the mills and four times as rich as the smelting ore shipped from Bisbee in recent years. As early as 1881, disputes arose among owners of various claims, and groups of claims, over the ownership of orebodies under the law of apex and extra-lateral rights. This law gives a miner the right to follow his vein downward on its dip, even

Jan 1, 1933

By Yuanbo Zhang, Ruijun Wang, Qian Li, Zhao Jing, Guanghui Li, Zhengwei Yu, Chen Liu

The high content of sodium and potassium in sinter is harmful for blast furnace ironmaking. Reductive sintering technology can remove more alkali metals than conventional sintering process. In order to improve the removal ratios of Na and K, reductive sintering with both CO-containing flue gas circulation and carbon-bearing pellet was conducted in this study. Experimental results show that all indexes except the VSV and P were improved in reductive sintering with CO circulation. Flue gas circulation technique combined with carbon-bearing pellets were beneficial to reductive sintering, because it could maintain good sintering indexes and enhance the removal of Na, K. The best removal ratios of Na, K and reduction degree of iron oxides were 20.37%, 63.73% and 23.76%. In reductive finished sinter, silicate mineral becomes the important binder phase, and main iron mineral phases are wustite (FexO) and magnetite (Fe3O4).

Jan 1, 2016

By Donald L. Katz, Marshall B. Standing

Density data are reported on 16 saturated hydrocarbon vapors at Pressures ranging from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. Introduction The densities of natural gases are necessary in many engineering in in petroleum production and utilization, Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 Ib. per sq. in.4 Recent discoveries of pools having Pressures UP to 7500 lb. Per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data On gas density at high pressures. Methods of Computation The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The meth-me-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most- of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir Or while on contact with liquid '''ring flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those consider. ably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions, This paper reports the density of I6 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure' have been modified and enlarged. A simpli-fied method of obtaining gas density is presented in the Form of charts, which apply for specific groups of gases.

Jan 1, 1942

By Marshall B. Standing, Donald L. Katz

Density data are reported on 16 saturated hydrocarbon vapors at Pressures ranging from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. Introduction The densities of natural gases are necessary in many engineering in in petroleum production and utilization, Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 Ib. per sq. in.4 Recent discoveries of pools having Pressures UP to 7500 lb. Per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data On gas density at high pressures. Methods of Computation The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The meth-me-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most- of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir Or while on contact with liquid '''ring flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those consider. ably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions, This paper reports the density of I6 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure' have been modified and enlarged. A simpli-fied method of obtaining gas density is presented in the Form of charts, which apply for specific groups of gases.

Jan 1, 1942

By A. J. Teplitz, T. Bardeen

In the course of an investigation of lost circulation, a new tool has been developed which gives a qualitative measure of the relative velocity between the fluid column in the borehole and the tool. The position of a diaphragm in the side wall of the instrument depends on the flow through the device. This position is established by using the conductive borehole fluid in a potentiometric circuit. The instrument has high sensitivity and can detect changes in velocity as low as. 5 ft/min. Lost circulation mud additives do not interfere with the satisfactory performance of the tool. In a number of circulation losses of the pressure induced type, the instrument has shown that the losses were confined to extremely narrow zones (less than I ft), indicating that such ruptures occur in a more or less horizontal rather than vertical plane as has often been assumed. This pinpointing of the zone of loss is important in remedial procedures since it allows the treatment to be applied directly to the point of loss rather than to the entire open hole. The device can also be employed for indicating points of entry of water in producing wells. INTRODUCTION The need for an improved means of locating the positions of lost returns zones became evident during an investigation of lost circulation difficulties in the Gulf Coast area.1 With instrumentation available at the time, it had been learned that, contrary to common belief, the position of the thief zone responsible for a given loss seldom coincided with the point of bit penetration at the time the loss was encountered. In the majority of cases, the losses were found to be occurring at some distance removed from the bottom of the hole —sometimes as much as a few thousand feet. This information, along with other observations made during the investigation, led to improved techniques' for dealing with lost circulation problems. Highlighted, however, among the results of this work and of similar studies subsequently conducted in drilling operations in other parts of the country, was the indication that a considerable portion of the difficulty and expense involved in treating prolonged circulation losses is due to the unsystematic application of remedial measures to one or more apertures of unknown position. Basis of Tests It is worth considering that if the troublesome formation could somehow be transported to the surface where it could be directly observed, there would likely be little difficulty in readily effecting a seal. Although this is a decided oversimplification of the situation, it does appear that the chief obstacles to similar ease of handling of a lost circulation zone in a well are lack of visibility and of ready accessibility. The latter handicap is overcome to a considerable extent by placement techniques already in use, and other procedures now in the process of development are expected to offer further improvement. But in the matter of visual observation, the technique to be presently described appears to afford a quite satisfactory substitute.

Jan 1, 1957

By A. B. Dyes

In the operation of a water-driven reservoir, a free gas saturation can he established by maintaining production rates fast enough to cause the reservoir pressure to decline below the bubble point. The benefit of such a procedure on the displacement efficiency of the oil by water is illustrated for two types of sandstone samples from one reservoir. Those rock samples showing the poorest recovery to water drive in the absence of a free gas saturation give the most improvement in the presence of a free gas saturation. Employing one type of reservoir fluid (low .shrinkage) the benefit of evolved gas on oil displacement is calculated at several reservoir pressures below the bubble point. This demonstrates the presence of air optimum pressure for water displace,rnent which is .several hundred pounds per .square inch below the bubble point. Displacement of oil at the optimum pressures results in the removal of 7 to I? per cent more oil than would be obtained by displacement at the bubble point pressure. In some instance. this magnitude of increase may be worthy of consideration in establishing the maximum efficient rate of production from many water-driven fields. INTRODUCTION For many years the belief that the use of gas could be combined with that of water to result in a better recovery operation than the use of either of these phases alone has been prevalent in the oil industry. This is evidenced by the several field trials which have employed the injection of gas and water in combination.1.2.v In most cases the small amount of any additional recovery, in combination with the limited knowledge available on the older reservoirs, has left uncertain the influence of gas on recovery in these earlier attempts to combine the use of gas with water. Research studies in recent years have demonstrated through laboratory. floods the magnitude of the benefit of the presence of gas on the displacement of oil from sandstones by water.5,6,7,8,9,10,11 In addition, studies of the distributions of the phases which are present during the displacement process have developed concepts concerning the mechanism by which this benefit is obtained."." It now remains for the engineer to incorporate these findings into the general technology of reservoir operations. It is the purpose of this paper to illustrate that the production of a water-driven reservoir at pressures below the bubble point is one such operation whereby improved oil displacement efficiency can be obtained as a result of gas evolution. The establishment of a gas saturation by evolution of dissolved gas was one of the techniques used by several investigators in the laboratory studies. The possibility of obtaining the benefit of gas evolution in water-driven reservoirs by producing at pressures less than the bubble point has 3150 been pointed out previously." The desirability of this operation has undoubtedly

Jan 1, 1955