Search Documents

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912

By Jr. Loper, M. H. Kim, H. H. Jo, C. S. Kang, T. S. Song

"An investigation has been conducted to describe the effect of grain refiner (e.g.,Ti) or modifier (e.g., Sr) on the microstructure of an Al-11.3wt%Si alloy produced by the Ohno horizontal continuous casting process using a heated mold so as to obtain directional solidification at high cooling rate of 300 to 2000°C/s. Experimental results demonstrated that the directionality of the primary a grain was promoted by the addition of0.2 to 0.4%Ti or by the addition of0.02%Sr, whereas the addition of0.6%Ti suppressed this directionality. Feathery a grains were promoted by the addition of 0.2%Ti, while these feathery a grains were suppressed when over 0.4%Ti (grain refinement) or when 0.02%Sr was added. The addition of Ti also resulted in increased coarsening of the eutectic Si in these Al-1 l.3wt%Si alloys.IntroductionThe mechanical properties of conventionally cast Al-Si alloys can be enhanced through judicious control of the casting parameters, by the addition of grain refiners (e.g., Ti) and by the addition of eutectic modifiers (e.g., Sr).[1-3] The Ohno continuous casting process[4-5] uses a heated mold (maintained at a temperature above the alloy liquidus temperature) to produce a casting with a mirror surface free of shrinkage defects. The process is especially suitable for the production of high quality and non-deformable rods of small diameter. This study was conducted at investigate the effects of Ti and Sr on the microstructure of Al-1 l .3wt%Si rods cast by the 01).no process."

Jan 1, 1998

By Carmen Mihaela Neculita

Sulfate-reducing passive bioreactors efficiently treat acid mine drainage (AMD) by increasing its pH and alkalinity and by removing metals as sulfide precipitates, in addition to hydroxides and carbonates. However, the new mining legislation sets discharge limits based on physicochemical parameters and on the non-toxicity of treated effluent as well. In this study, toxicity was assessed for effluent from 3.5 L column bioreactors filled with mixtures of natural organic carbon sources and operated at two different hydraulic retention times (HRTs) of 7.3 d and 10 d for the treatment of a highly contaminated AMD. Acute toxicity was observed for D. magna, and a toxicity identification evaluation (TIE) procedure was performed to identify potential toxicants. To help the interpretation of the toxicity results, metal partition in the effluent was also determined by filtration and ultrafiltration, while geochemical modeling was performed for metal speciation evaluation. The 10 d HRT effluent was nonacutely lethal for rainbow trout but acutely lethal for D. magna, whereas the 7.3 d HRT effluent was toxic for both organisms. The toxicity to D. magna was eliminated by 2 h of aeration for the 10 d HRT effluent, and the TIE procedure suggested iron as a cause of toxicity. However, the 2 h aeration eliminated the toxicity of the 7.3 d HRT effluent, only if performed after the pH rising to 9.3. Data regarding metal speciation indicated instability of both effluents during aeration and were consistent with the toxicity being caused by iron. The study indicates that design of passive treatment should include sufficient HRT and posttreatment aeration to meet acute toxicity requirements. Keywords: acid mine drainage, sulphate-reducing passive bioreactors, hydraulic retention time, effluent toxicity, metal speciation

Nov 1, 2008

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different methods of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approaches. This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

I propose to speak today about our mineral heritage. In common usage "heritage" refers to the past. It means the discoveries, the developments, the mines and the processing plants, the benefits, the consequences, and the human experiences flowing from these. The history of the industry, inseparable from the history of the countries in which The Institute operates, is a rich background of which we can all be proud.But there is also a much wider meaning to mineral heritage. Our past has left us with the ab\lity to create and operate world scale enterprises generating wealth for the community, the ability to offer satisfying and challenging careers in a wide range of skills to our young people, and the willingness to follow adventurous and challenging vocations in remote areas, away from the big cities, at a time when the mentality of many is to get the most for the least effort and at the least inconvenience to themselves. The industry continues to be the repository of the pioneer spirit and a vital contributor to improving the life of the people in our countries.Thus, while our mineral heritage has much to do with the past, an essential part of it is how we use this rich past to build and shape our future. It is in this broader context that I am speaking today.

Jan 1, 1990

By K. F. G. Hosking

I read Professor Gaudin's paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S,), is ground with sodium or potassium hydroxide, the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture.

Aug 1, 1956

By M. Loan

The Zinifex's Hobart Smelter uses the paragoethite process to remove dissolved Fe(III) from concentrated zinc leach liquors. This produces a residue consisting primarily of 6-line ferrihydrite (a hydrated Fe(III) oxyhydroxide), several insoluble components derived from the calcined zinc concentrate neutralization agent and other precipitated phases, such as jarosite and silica. The precipitation of 6-line ferrihydrite in the paragoethite process was studied using a laboratory-scale continuous crystallizer, and the conditions were selected to limit high levels of dissolved silica and jarosite. This approach allowed the reactor pH and the rate of precipitation to be correlated with residue solid-liquid separation, particle size, morphology, residual zinc and sulfate concentrations, and phase formation (e.g., goethite, jarosite, schwertmannite, and 2- and 6-line ferrihydrite). These studies delineated the mechanism of 6-line ferrihydrite precipitation in the kinetically controlled paragoethite process, and its inter-relationship with goethite and jarosite precipitation under conditions where 6-line ferrihydrite is favoured. Unexpectedly, the generation of a more crystalline goethite precipitate with larger "primary" particle size did not produce a residue of improved properties, as bulk aggregates dictate the physical properties of the residue and not the crystallinity. Furthermore, it is difficult to precipitate 2-line ferrihydrite or schwertmannite under existing paragoethite process conditions.

Jan 1, 2006

By George M. Hamilton

The gas producer actually dates back far beyond the period from which we first find recorded data. A partial production of producer gas can take place in any type of solid fuel grate equipment, such as a boiler, or even a fireplace if a sufficiently deep fuel bed is provided. Those of us who have watched a coal fire burning in the hearth, have no doubt noticed at times, the gases liberated by the heat burning on or near the surface of the fuel bed. So far as we know, the first gas producer was built by Bischof in Germany in 1839, followed by Ebelman in France in 1840, and Ekman of Sweden in 1845. The first large industrial development in the use of gas producers was When the two Siemens brothers of Germany patented their first combined gas producer and regenerative furnace in 1861, thus opening up the field for the use of raw, crude producer gas in heavy furnace work. In the years 1879-1881 J, E, Dowson, of England developed a producer gas cooling and cleaning plant, which extended the scope of application of producer gas to make possible its use in small furnaces and gas engines.

Jan 1, 1961

By Jizeng Zhao, Li Liu, Weiqing Chen, Jinxia Meng

This paper discusses the utilization of chromium slag, which presently has no useful application in China, as a resource. The following research has been done in this paper: (1) After determining the composition and properties of chro- miumresiduewedecidedtotesttheideaofusingchromiumslagasacomponentin synthetic MgAl O spinel material. (2) Through experiments on sintering and 2 4 electric melting of refractory materials we determined the best conditions for a practical process. (3) We compared the performance of the refractory material obtained with traditional spinel refractory materials and confirmed the excellent performance ofoursystem. The results show thefeasibilityofpreparing MgAl O 2 4 spinel material from chromium slag by electric melting. (cid:1) (cid:1)

Mar 1, 2018

By H. N. Lawrie

Introduction. THIS study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility-two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten ' and Levol,2 using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleabilitytests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi2O3, on the copper protoxide, CuO. Hampe's conclusions of the influences of these two latter compounds of bismuth on copper are as follows "If the protoxide of bismuth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Sep 1, 1909

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993

By A. J. Goss, M. Tanenbaum, W. G. Pfann

THE purification of two metals, antimony and tin, by zone refining is described, and a reciprocating method of passing molten zones through a straight ingot, which effects a considerable economy of time and apparatus, is discussed. Antimony has been used extensively as a doping agent in germanium and silicon. More recently, it has become important in the preparation of new semiconducting compounds such as InSb, GaSb, and AlSb. High purity is especially necessary in this latter use, since the antimony may comprise as much as 80 pct by weight of the compound. Antimony is generally available in a commercial form of about 99.8 pct purity. Column 1 of Table I is a typical emission spectra analysis of commercially available 99.8 pct antimony. Zone refining has been quite successful in increasing the purity of such samples. Columns 2 to 4 of Table I are analyses of an ingot of the antimony of column 1 after the passage of seven molten zones in an atmosphere of nitrogen. The ingot length was 9 1/2 in.; the mean zone length was 2 in.; convection was the only means of stirring. The column headings are sample locations in inches from the leading end of the ingot. The results illustrate both the merit and a limitation of zone refining. It is seen that four of the five impurities—nickel, arsenic, lead,

Jan 1, 1955

An old philosopher once said, "God grant me the serenity to accept those things I cannot change, the courage to change those which I can, and the wisdom to know the difference." It is time to take stock of how the human race has progressed-whether the trend now points toward greater evils or finer things. It is time that we stop fooling ourselves and put into effect a program of "real" conservation. By this it is not meant that we limit our concept to planting new forests, preserving wild life or preventing soil erosion, but rather taking stock of the expectancy of our resources, expanding human resourcefulness and effecting careful utilization and replacing of, or producing substitutes for, material resources. Man is still dependent upon energy and matter in certain usable forms, despite the fact that energy is inherent in all matter. Until such progress is made that the energy contained in all matter can be controlled, man must continue to utilize the common fuels. Advancement of research in atomic energy has cast a gleam of hope for future use of the tremendous energy contained in the atom. Use of atomic power for industrial pursuits would open up limitless resources of power. This energy, of course, is a two-edged sword, since man's progress and his means of destruction have always evolved parallel to each other. Thus it is estab-

Jan 1, 1950

By H. J. Seaman

The cost of keeping platinum ware in repair becomes such an important item in laboratories where much fusion-work is done, that a method of saving in this direction may not prove unacceptable to at least some of the members of the Institute. Some two years since I had the misfortune to puncture an almost new Bishop crucible. As an experiment I endeavored to patch it, and with such success that it is still in constant use. This may be accomplished in the following manner : The crucible and patch, which should be of stout foil, are rubbed bright with silica, or rotten-stone; a light platinum wire, welded to a corner of the patch, and the whole treated for several hours with hot concentrated hydrochloric acid; after which they are thoroughly washed with distilled water and dried. The head of an ordinary iron rivet, 4 inches by $ inches, is rounded off by hammering to somewhat the shape of the crucible. This is sunk 2 inches in a block of hard wood, and firmly wedged in place. This serves for an anvil. The hammer is an ordinary cast-iron toy, 11/2 inches long, and # inches in face, mounted on a 4 inch iron rod, 10 inches long. A gas-blowpipe is fixed in a horizontal position, and the strongest heat obtainable with it directed upon the rivet head; this soon at-

Jan 1, 1885

By Jeff Bird, Xijia Wu, Prakash C. Patnaik

"Prognosis and health management (PHM) is an evolving suite of technologies intended for application to the life cycle management (LCM) of mission/safety critical systems, with anticipated results, which will: - Reduce life cycle cost - Enhance operational safety and readiness - Assist in maintenance decision-making - Enable autonomic logistics While it is emphasized in the United States that future multi-mission fighter aircraft such as Joint Strike Fighter (JSF) must have PHM capabilities, Canadian initiatives also recognize the need to implement such schemes for future and legacy military and civil aerospace systems. With respect to four major technology areas of PHM, i.e., i) advanced sensors, ii) data analysis and fusion, iii) life consumption evaluation, and iv) predictions with reliability/risk assessment, there has been advanced technologies developed by NRC and others within Canada: - Aircraft/engine instrumentation and airborne data recording systems - Signal analysis and data fusion - On-line engine health monitoring - Physics based models for engine material failure modes and life prediction - Autonomic crack growth analysis for damage tolerance of engine components - Mission severity analysis algorithm - Probability, reliability and risk assessment This presentation reviews the above technologies in relevance to PHM, emphasizes the need to have physics based models and outlines the future R&D needs for integration and implementation of these technologies suitable for the advanced and legacy aircraft."

Jan 1, 2004

By D J. Thobaven

Project financing challenges caused by declining commodity prices have heightened the need to improve project metrics such as minimising capital payback and maximising net present value (NPV). Khnaiguiyah Mining Company (KMC) recognised the need to improve early cash flows at their Khnaiguiyah zinc-copper project after initial studies showed the project could not provide the desired financial outcomes necessary to compete for investment dollars in the current market.A significant improvement to the project cash flow in early years was realised through simultaneous optimisation of cut-off grade, mining sequence and strategic stockpiling. This improvement was achieved by accelerating mining in the pits, stockpiling lower value material and feeding higher value material directly to the plant. The schedule required higher mining and stockpile capacities than the sequential mine plan although minimal change occurred in the definition of ore and waste as measured by tonnes and grade. The practicality of the strategic schedule was demonstrated by implementation in the production plan with excellent conformance.CITATION:Thobaven, D J, 2014. An application of simultaneous optimisation – improving the payback period of a zinc-copper open cut project, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977