Search Documents

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (&gt;0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By R. Taggart, G. R. Purdy

DURING a study of the tempering of ß-quenched alloys of cobalt in titanium, parallel lines were observed crossing certain faces of retained-ß crystals in the early stages of tempering, Fig. 1. The lines closely resemble stress-induced martensite&apos; or substructures attributed to clusters of faults in titanium-nickel2 and copper-silicon3 alloys. The markings were observed only in intensely etched quenched and tempered alloys having compositions ranging from 4.5 pct* Co (the composi- formed by the lines was reproduced upon repolishing and reetching. Close metallographic examination indicated that the markings were troughs, Fig. 2, and that the characteristic surface substructure persisted within the troughs. The occurrence of the troughs was associated with the age hardening reaction due to the metastable u) phase (previously reported in titanium-cobalt alloys by Raub and Beeskow4 and indicated in this work by the broadening of 0 diffraction peaks and by hardnesses approaching 600 Dph). The troughs

Jan 1, 1961

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,&apos; Morozov and Novokharski,&apos; and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By R. Gilman Brown

INTRODUCTION. MINES are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique geological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.&apos; On the other hand, this output has been mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness-from 0.5 in. of "specimen rock" to 30 ft. of clay and quartz; distributed through a zone about 2,000" ft. in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a few miles from its western edge, marked here by Mono lake on the line of the Great Fault. The average elevation of the outcroppings of the veins may be taken at about 5,700 ft. The andesite projects from south to north in a great tongue, 12,000 ft. long and 5,000 ft. wide, reaching an extreme height at the northern end of perhaps 1,000 ft. above the adjoining small canyons. These separate it from the main mass of the foot-hill

Jul 1, 1907

By J. E. Hoffman, S. P. Sandoval, T. J. Keefe, K. P. V. Lei, O&apos

The U.S. Bureau of Mines investigated the use of the Fe2+/Fe3+-SO2 (FFS) anode reaction in the copper leaching-solvent extraction-electrowinning circuit. The investigation revealed that six process variables, including anode type, Fe 21 concentration, current density, electrolyte temperature, degree of agitation, and manifold injection point were found to influence cell voltage and cell current efficiency. A 47% voltage reduction (0.8 versus 1.5 V) compared to conventional electrowinning with activated lead (ALE) anodes was achieved at a current density of 258 A/m2 (24 A/ft2) with an industrial electrolyte. Current efficiency was maintained above 90%, and S02 above the cell measured less than 1 ppm when activated carbon was used to assist the reduction of Fe" by S02 in the copper electrolyte. Solvent extraction tests showed that Alamine 336 is a stronger H2SO4 extractant than is needed to extract the excess acid produced by the FFS anode reaction.

Jan 1, 1993

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

By O. Kökkilic

This study covers the tests to develop separation process for production of clay and colemanite rich concentrates, and aims to serve the clay and colemanite concentrates extracted from the tailing dams to the industrial applications. For this purpose, samples from the tailing dams in Kestelek Boron Plant (Turkey) with an average B2O3 content of 8%~11 % were subjected to the investigations. The separation process of hydrocyclone--to make clear the way to obtain either clean clay or cole-manite--was initially discussed. Therefore, following the gentle scrubbing (to keep the bimodal size distribution between clay and colemanite) of the tailings to disperse the slurry, two alternative multistage hydrocyclone processes; allowing to recycling the overflows or underflows to concentrate clay and colemanite were respectively tested. As a result of the preliminary tests, the multistage hydrocyclone separation in direction to the clean colemanite concentrates (recycling the underflows) gave the better separation efficiencies. So, all the parameters such as apex and vortex finder diameters and feeding pressures were examined with the multistage hydrocyclone process allowing the recycling the underflows. The detailed multistage hydrocyclone separation process of the tailing dam wastes yielded with colemanite concentrates (approx. 12 % of the feed, w/w) with B2O3 content of 35.0 % and the clay concentrates (approx. 42 % of the feed, w/w) with B2O3 content of 2.1 %. Colemanite concentrates were found good enough either to re-feed in to the separation process or to keep upgrading for final product ready to use in Industry whereas the attempts on production of light bricks from clay concentrates has failed. But it is worth to point out that these clay concentrates can be used for agricultural purposes just in the form as it is.

Jan 1, 2014

By Edward L. Mooney

In the, West, walking draglines often offer the least cost method of uncovering coal for surface mines. However, with each of these machines costing millions of dollars, a good deal of analysis can be justified by the potenial savings or, conversely, costs associated with the choice of a machine. This has resulted in the recent development of a number of computerized models for dragline selection and pit design. One of the earliest reported models for this purpose was developed by Dunlap and Jacobs (1). Later, Rumfeldt described the computer approach to sizing stripping draglines given the required production rate and mine site parameters (2). This basic approach is probably still the most widely used with models for more complicated mining methods reported by Stefanko, Tomica, Finch, as well as others (3,4,5). furthermore, detailed simulation models useful in this regard have been developed by McDonnell Douglas and Fluor, Utah (6,7)

Jan 1, 1982

By Derek Morris, Vito Saccheri

In the monitoring of seismic exploration (whether by explosive or vibratory energy sources), the intensity of shaking at neighboring structures can now be measured quite accurately and comprehensively with portable equipment. However, the interpretation of the results is open to considerable debate and mis-interpretation. One conventional approach is simply to compare the maximum measured peak particle velocity (PPV) with a permissible standard – usually 0.5 inches/sec (1.3 cm/sec) because this is the value generally referred to in the U.S. Bureau of Mines standard. This can be very conservative, both for surface structures, and especially for buried structures like pipes, for which absolute reliance on PPV obscures the true complexity of field problems. Quite apart from the fact that the full Bureau of Mines standard is actually a reasonably complex function of frequency (for the simple reason that in differing parts of the frequency spectrum, damage may be displacement or acceleration controlled), the effects of spatial direction and orientation are often ignored.

Jan 1, 2009

By David R. Maneval, H. B. Charmbury

At the turn of the century, iron and coal were the keys to industrial prosperity. At that time, Pennsylvania was the leading mineral producer in the Country, producing 200,000,000 tons of coal in a typical post-World War I year. Close to 90% of the Nation&apos;s energy was generated by coal. Today, coal accounts for but 22% of the energy generated, leading to a drastic reduction in Pennsylvania coal output. In contrast with the post-World War I days, 1964 figures showed a drop in production to 93,846,480 net tons. This huge decrease has created a serious economic problem in a state so much dependent on the coal industry. Along with the reduction in coal production, employment has dropped considerably through these years (the number of miners alone has gone from 280,011 to 43,149), thus causing a heavy burden of supporting the unemployed on the taxpayers. As far back as 1939, coal operators and economists saw the problems on the horizon and the need for improvement. Realizing that research was a way to improve and stabilize the industry they demanded legislative action. The Legislature reciprocated with a small grant to The Pennsylvania State University with the provision that each State research dollar be backed with one from the industry. This initial grant laid the foundation for the further growth in coal research.

Jan 3, 1966

Natural gas is a comparatively new fuel in Australia. It was first used in small quantities in Queensland in 1965, but it was not until 1969 that natural gas reached the capital cities Brisbane, Melbourne, and Adelaide in that order; then in 1971 it reached Perth. By the mid seventies, natural gas had secured a significant proportion of the energy markets in Queensland, Victoria, South Australia and Western Australia and in 1976 supply commenced in Sydney. In that year - 1976 - gas supplied about 12.5% of the total demand for primary energy in Australia excluding transport. In the current financial year - 1981/82 - natural gas is expected to supply nearly 19% of the market and forecasts for 1990 range up to 25%. From a starting point in the late 1960&apos;s when manufactured gas supplied a small but important proportion of the non-transport energy market - less than 3% - we have exper- ienced an average growth of nearly 24% per annum up to the present time.

Jan 1, 1982

By H. D. Hoskold

I. Instrument-Parts and Implements. Cross-hairs ; Stadia-measurement; Fineness of Graduation ; Cylindrical Gradu ation ; Nonius; Vernier ; One Vernier or two ; Leveling-Screws ; Troughton & Simms&apos; Shifting Tripod-Head ; Hoskold&apos;s Shifting Tripod-Head; Hoskold&apos;s Extensible Tripod ; Electric Lamp ; Plumb-lines; Chain. II. Instruments. Compass (Mine-compaes of 1518, Compass of 1541, and Agricolals of 1556, Voig tel&apos;s Setz-compass, Circumferentor, Stanley&apos;s Hedley Dial, Compass on Tele scope, Hanging Compass, Lack of Precision) ; Plane-table; Octant and Quadrant; Theodolite and Transit (Evolution of the Theodolite, Scott&apos;s Tachymeter, Hoskold&apos;s Engineer&apos;s Theodolite, Angleometer, Precision of Mine-Theodolites). I. Instrument-Parts and Implements. Cross-Hairs.—Mr. Scott‡ says Lean&apos;s dial " might also have been provided with a diaphragm and cross-hairs; for Huygene discovered that any object placed in the common focus of the two lenses of a Kepler telescope (1611)- appeared as distinct and well defined as any distant body. Following this established theory, in 1669 Jean Picard, Marquis Malvasia and others crossed silken fibers in the mutual focus of their astronomical instruments." If by this Mr. Scott means that Huygens and Picard first devised and applied cross-hairs to the focus of the telescope, the writer cannot agree with him. Huygens did not describe " his telescope without tubes until 1684, in his Astroscopia Compendiaria."§ Moreover, it is recorded that the English astronomer, Gascoigne,?

Jan 1, 1902

Plans for the fall meeting of the AIME, to be held in conjunction with the Centennial of Engineering -marking the 100th anniversary of the Society of Civil Engineers-indicate that the Chicago gathering will be one of the most significant in Institute history. Headquarters for the six divisions represented will be the Palmer House. Twenty technical sessions will be held from September 3 to 6, with papers of industry-wide impact to be presented. The papers will follow the theme of the celebration-a century of engineering progress. The MBD will start the ball rolling with morning and afternoon sessions Thursday, September 4. A luncheon also will be held. MBD has scheduled morning and afternoon sessions for the following day as well. MGGD, Iron and Steel, and the Coal Div., will hold sessions Friday afternoon. The Industrial Minerals Div. plans an executive meeting, 5 pm, Friday. Geology Subdivision is slated for morning and afternoon sessions Saturday. The Coal Div. will meet again Saturday morning.

Jan 1, 1952

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol&apos;s cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol&apos;s estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By Olli Järvinen

The precious metal refinery process is divided into the five process stages: 1 .copper/nickel leaching in autoclave 2. selenium roasting furnace 3. doré metal smelting furnace 4. silver electrolysis 5. gold recovery system. The process has been developed during the years in Outokumpu Harjavalta Metals, which treats about 600000 kg /year copper anode slime. The slime treatment process route in Outokumpu Pori plant has been developed from year 1941. During this period the process has been improved radically. The major changes has been the atmosphere leaching into the autoclave leaching, the sulfuric acid roasting furnace was changed into sulfuric dioxide / oxygen roasting. The old doré smelting furnace has changed into the TROF converter and the gold electrolysis / aqua regia process has changed into the quick hydrochloric acid leaching process. The current production in Pori plant is 30000 kg of silver, 1000 kg gold, 30000 kg of selenium and some hundred kg of platinum- palladium concentrate.

Jan 1, 1995