Search Documents

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

By John R. Freeman

The die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the minimum amount of scrap to be sheared from the pressing as it comes from the die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

By Frank C. Aplleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO4•2H2O) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [Sulfur Combined Lime Trioxide Water (CaO) (SO,) (H2O) Gypsum 32.6% 46.5% 20.9% Anhydrite 41.2% 58.8% -] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product. End Uses The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris (the hemihydrate of calcium sulfate, CaSO4 ½ H2O) which when mixed with water will set or harden as the calcium sulfate returns to the dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uncalcined uses of gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in less developed countries where construction and other industrial uses may be quite limited, the use of uncalcined gypsum for portland cement retarder may well be the dominant-if not the only-market for the mineral. It has often been noted that calcium sulfate constitutes the world's largest reserve of sulfur, and minor use of both anhydrite and gypsum has been made to produce sulfuric acid or other sulfur compounds such as ammonium sulfate. However, because sulfur is readily available at lower cost from other sources, use of calcium sulfate has been limited to only a few locations where it could compete economically. No such use is reported in the United States at this time. Mineralogy Anhydrite, CaSO4 because of its geologically rapid conversion to gypsum, and relatively high solubility (about 0.2 g per 100 g H2O) is not often found outcropping in climates wet enough to support abundant vegetation except on steeply dipping slopes or other places where hydrated material is continuously removed. Anhydrite rock is most often light to bluish gray in color, and under the microscope, varies

Jan 1, 1983

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By C. W. Greenhalgh

THE accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (I) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries are poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money, or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend. A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. OBJECT OF EXAMINATION The purpose of prospecting any mineral deposit is to secure sufficient samples from which ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, upon the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By Huntington Adams

The arrangement of a flow of cyanide-pulp through Pachuca tanks in agitation, so as to permit a continuous process, instead of alternate filling, agitation, and emptying, has been proposed by various writers within the last two years, and more particularly by A. T. Grothe, agent for the Brown patents on Pachuca tanks in Mexico. It was first put into practice, I believe, by M. H. Kuryla at the Esperanza mine in El Oro, Mexico. The starting of agitation in Pachuca tanks after filling may offer no serious difficulties with ores which do not settle rapidly in such tall tanks; and the adaptation of the tanks to continuous agitation under such conditions may give simply a somewhat more convenient method of treatment and greater agitation-capacity for a given number of tanks, because of the saving of time lost in filling and discharging. But in the treatment of pulp which tends to settle rapidly, as in the cyaniding of concentrates or of the whole pulp of ores containing heavy sulphides, the packing of the slime at the bottom may cause much trouble. The use of the radial air-pipe attachments near the top of the cone and of the air-valve outside of the air-lift tube at the bottom may obviate the difficulty to some extent; but the action of the radial air-pipes on the cone-sides is that of a sand-blast, and their continuous use cuts through the tanks. Moreover, even when these pipes are used, some pulps will pack tightly below them in the cones. Under such conditions the use of Pachuca tanks with intermittent filling and discharging becomes a troublesome process. Time is lost in starting agitation; large quantities of compressed air are wasted; pulp is blown over the tank-tops; and not infrequently it may be necessary to dig out the bottoms of tanks by hand. This trouble is the only important one occurring in the use of Pachuca tanks; and, since it is caused by intermittent filling, the arrangement of a continuous flow of pulp from tank to tank,

Jan 1, 1912

By Malsuzaki. Kenji

A mathematical simulation model of the Imperial Smelting Furnace operation has been developed for purpose of improving the furnace operation. The model consists of top, shaft and bottom regions. Analysis in the shaft region is based on differential heat and materials balances taking account of reaction kinetics and heat transfer rates, and those in the top and the bottom regions are based on heat and materials balances under a steady-state condition. Longitudinal distributions of process variables such as temperatures of gas, sinter and coke, gas composition and fractional conversion under a practical operating condition were calculated. With this model, the furnace performance under various operating conditions also can be shown reasonably predicted.

Jan 1, 2003

By Phillip J. Maddex

Transportation is a major part of yours in the industrial minerals industry. Whereas federal income taxes merely take 50 per cent of your firms profits, transportation cost may take 50 per cent of the gross realization - selling price plus transportation - on your product, f. o. b. customers plant.

Jan 1, 1969

By William C. Sleppy

The nmgnetic susceptibility of heat-treatable aluminuin alloys is sensitive to chanyes such as solution or dissolution of solute and the precipitation of mew phases. By measuring the change in the magnetic susceptibility of aluminum alloys caused by various heat treatments, an empirical relation was found from which atomic arrangements in dilute binary alloys of copper, zinc, and magnesiutn in aluminum have been delineated. The relation predicts the ultimate formation of C1LA12 when copper is precipitated from solid solution in aluminum. Euidexce joy silovt- range order is found for copper in solid solution in aluminum in the sense that copper atoms avoid being nearest neighbors to an extent greater than would result from a purely random arrangertzeizt. Hume-Rothery has predicted such short-range order joy solid solution of copper in aluminum The Al-Zn system agrees with evidence obtained from X-ray scattering at small angles and predicts a tendency for zinc atoms to cluster in solid solution in aluminum. In the Al-mg system, the empirical relation indicates an approach to randor distribution of magnesium in solid solution in aluminum with a tendency for magnesium segvegation which increases with incveasing temperature. ThE magnetic properties of metals are complicated by the fact that contributions are made to them both by electrons of a "metallic" type which belong to the crystal as a whole, and by electrons in states localized on particular atoms. An expression1'2 for the bulk magnetic susceptibility of aluminum may be written as the sum of three contributions: where XA1 is the bulk susceptibility of aluminum per gram of material (in the cgs system, the units are those of reciprocal density); Xa1+3 is the diamagnetic contribution of the electrons localized in ion cores; Xa1 is. the paramagnetic spin contribution of conduction electrons often called Pauli paramag-netism: Xa1 is the diamagnetic contribution of the conduction electrons often called Landau diamag-netism. Ion core diamagnetism arises from the precession of the electron orbits which occurs when a magnetic field is applied to a system of electrons moving about a nucleus. Its contribution to the magnetic suscepti- bility is small, temperature-independent, and unaffected by alloying. The conduction electron diamagnetism is also temperature-independent and arises from the translatory motion of the electrons. For perfectly free electrons this contribution should be exactly one-third of the Pauli spin paramagnetism, but this relation is seldom even approximately true. Blythe2 determined the conduction electron diamagnetism in pure aluminum and found it to be extremely small. Any change in the conduction electron diamagnetism caused by alloying is neglected in this work. The Pauli paramagnetic contribution3 to the magnetic susceptibility of aluminum depends upon the number of electrons that occupy excited states and whose spins can be turned parallel to an applied magnetic field. The number of electrons free to turn in the field is proportional to the temperature and each spin contribution to the susceptibility is inversely proportional to the temperature. A slight temperature dependence of Pauli paramagnetism occurs when the number of electrons occupying excited states cannot increase sufficiently to balance the inverse dependence on temperature of each spin contribution. The decrease of the magnetic susceptibility of aluminum with increasing temperature is attributed to a temperature dependence of the Pauli paramagnetism. Estimates of the Pauli paramagnetism of aluminum have been made by several workers.2,4,5 All of the values are in reasonably good agreement with each other. In this work Xal at 17°C is taken as 0.761 X 10-8 cu cm per g. An expression similar to [I] can be written for the magnetic susceptibility of an aluminum base alloy containing a fractional weight percent x of solute:' Xa = (1 -x)XAl+3 +xXsoluteion * XaPauli +Xadia) [2] where X, is the magnetic susceptibility per gram of alloy, Xal'3and Xsolute ion are the ion core diamag-netic contributions, and xpauli and xdia are the Pauli and diamagnetic contributions of conduction electrons in the alloy. If the components of a mixture are not alloyed but simply mixed together in their pure states without producing a new phase, then the magnetic susceptibility of the mixture is given by the Wiedemann additivity law: Xm =x1X1 +x2x2 + ..xnxp [3] where X, is the susceptibility per gram of mixture and xnXp are the weight fractions and susceptibilities, respectively,-. for the pure components. The additivity law is not applicable to alloys because the outer electronic structures of the components are changed by alloying.' Both the Pauli paramagnetism and Landau diamagnetism are affected; hence the magnetic susceptibilitv of an alloy is usually different from that calculated using the additivity law. In this work the difference, X, -X,, is taken as a measure of the change caused by alloying.

Jan 1, 1968

By Igor Gonzales G.

The Southern Peru Copper Corp. (SPCC) recently built an integrated copper project consisting of dump- and heap-leaching operations at its mine complex in Peru. The pregnant leach solution (PLS) containing the solubilized copper from the leaching operations is processed in a new solvent extraction/electrowinning (SX/EW) facility to produce high-purity cathode copper. The dump leaching and SX/EW facilities are located near the Toquepala mine site. The crushing and heap-leaching operation is located at the Cuajone Mine. The pregnant leach solution from Toquepala and Cuajone is pumped 35 km (22 miles) to the SX/EW plant at Toquepala. The SX/EW plant consists of three trains of solvent extraction (SX), a tank farm area and an electrowinning (EW) facility. The solvent extraction plant has a total PLS flow capacity of 3,210 m3/hr (113,360 cu ft/hr). The electrowinning facility has an expected long-term production capacity of 97 t/d(107 stpd) or about 35 kt/a (38,500 stpy) of cathode copper. However, present production exceeds the expected long-term by about 20%.

Jan 1, 1996

By Jr. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Laser-based instruments are used in areas where coal dust ignition presents a safety hazard. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory ~NIOSH, PRL! is conducting a study to help determine when an optical beam may be considered a potential ignition source in underground coal mines or coal storage facilities. Researchers conducted experiments to determine threshold igniting powers for Pittsburgh seam bituminous coal dust clouds using an 803 nm continuous wave laser. For fine sized coal dust dispersed in air, concentrations ranging from 600 to 2000 g/m3 were the most easily ignited. A heated layer of coal dust that deposited on the fiber tip during dispersion ignited the dust clouds. Minimum observed igniting powers for laser beams delivered by 200, 400, and 800 mm core fiber optic cables and directed into coal dust clouds were 2.0, 3.0, and 5.0 W, respectively. Threshold igniting power was proportional to beam diameter, and threshold igniting power density decreased with larger fiber diameters. Ignition delay times averaged 0.6 s and did not vary significantly with laser power under initially turbulent test conditions and with flammable targets. Comparisons are made with the results of other researchers.

1. Book review Assay and analytical practice in the South African mining industry, byW.C. Lenahan and R. de L. Muray- Smith. Johannesburg, The South African Institute of Mining and Metalurgy, 1986. RlOO (R80 to Members). Reviewer: N.G. Randolph 2. Canadian publications A market profile for industrial minerals in Canadian manufacturing sectors, by M. Prud'homme and D. Francis. 1987. Micromedia Limited (144 Front Street, Toronto, M5J 1G2, Canada).The following three publications are available from the Centre for Resource Studies, Queen's University, Kingston, Ontario, Canada K7L 3N6. An analysis of Japanese coking coal procurement policies: The Canadian and Australian experience, by D.L. Anderson. Feb. 1987. $25. Technology policies in the Canadian mineral industry, edited by M.J. Wojciechowski. Sep. 1986. $20.Value-added taxation: Issues and impact for Canadian mines, by B.l. Dyack. Nov. 1986. $7.3. Mintek reports Report M295 A mineralogical investigation of refractory gold ores and their beneficiation, by P.M. Swash. Report M296 The determination, by distilation-spectrophotometry, of chlorine in apatite-type materials containing fluorine, by M. Solomons. Report M297 The interference of zirconium in atomic-emission spectroscopy using inductively coupled plasma, by P.l. Wright.

Jan 1, 1987

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By Charles E. Heinrichs

There arc still ample reserves of phosphate in Florida and Tennessee, but the richest low-cost areas have been exhausted. The miners, by the introduction of more efficient equipment, have succeeded in preventing material increases in production costs. Further mechanical improvements could not be expected to keep up with the factors tending to increase costs. While the conventional phosphate "washers" are capable of recovering practically all of the plus 1.5-mm. phosphate from the matrix, approximately 50 per cent of the phosphate values are in the minus 1.5-mm. sizes. Flotation now affords an economical and efficient means for recovering the fine ( — 1.5 mm.) phosphate formerly discarded to waste dumps. Through the reclamation of dumps and recovery from current washer wastes, flotation has doubled the reserves of Florida and Tennessee. By doubling recoveries from the matrix, flotation reduces capital investment requirement and substantially reduces production costs. It definitely improves the grade of the total production and provides a flexibility of operation that cannot be obtained by any other known means.

Jan 1, 1934

By William B. Plank

Mineral engineering student enrollment in U. S. and Canadian schools for 1955-1956 is 11,408, an increase of 11 pct more than last year. The undergraduate and graduate engineering students in both countries number 251,765, or 13 pct more than last year. These figures have been released by the American Society for Engineering Education. The largest increase in the undergraduate mineral engineering group in the U. S. is in ceramic engineering, with 676 students, or 31 pct more than last year. The next largest increase is in mining which shows a gain of 13.5 pct, compared with a gain of 13.1 pct in the total undergraduate enrollment in all engineering schools approved by the Engineers' Council for Professional Development. This figure is 190,355, which approaches the prewar figure. Metallurgical undergraduates increased 13 pct; geological, 5 pct; and petroleum, 2.5 pct. This year the figures for geophysics are combined with those for geological engineering, making a total of 1610 undergraduates, of which the geophysicists comprise about one seventh.

Apr 1, 1956