Search Documents

By Louis Raymond, John E. Dorn

The object of this investigation was to analyze the recovery that arises when the stress on a specimen undertaking creep is reduced. For this purpose annealed specimens of high-purity aluminum were precrept under a stress of 1000 bsi to a strain of 0.08 following which the stress was reduced for various periods of time to 10, 250, 500, or 700 psi. When the original stress was reapplied the subsequent creep curve lay above that for the unre-covered state and below that for the original annealed state. Analyses on the kinetics of this recovery as a function of the temperature gave a stress-sensitive activation energy that decreased as the reduced stress was increased from a value of 64,000 cal per mole at 10 psi to 37,000 cal per mole at 750 psi. Recovery was also detected and measured during creep under the reduced stress. Following a short initial period, the creep rate under the reduced stress increased monotonically until it reached the secondary-creep rate for the reduced stress. The temperature dependence of this phenomenon was also shown to be correlatable in terms of the previously deduced activation energy for recovery. The activation energies for creep of most pure metals at high temperatures have been shown to agree well with those for self-diffusion.'j2 Since the true secondary stage of creep is usually due to the steady-state balance between the rate of strain hardening and the rate of recovery, it is generally thought that the activation energy for recovery of the creep-induced substructure equals that for creep itself. A shoft time ago, however, Ludemann, Shepard, and Dorn~ found that the activation energy for recovery of the creep-induced substructure in high-purity aluminum under zero stress was almost twice that for self-diffusion, namely about 65,000 cal per mole; obviously recovery under reduced stresses differs in some significant way from the recovery that accompanies the secondary stage of creep. The major purpose of this investigation is to study the effect of stress on the re- covery of the creep-induced substructure in order to provide a better understanding of the recovery mechanism itself. EXPERIMENTAL TECHNIQUE High purity aluminum, containing 0.004 pct Cu, 0.002 pct Fe, and 0.001 pct Si, used in this investigation, was in the form of 0.100-in.-thick sheet which has been cold-rolled to the H-18 temper. Creep specimens were milled from the sheet with their tensile axes in the rolling direction. All specimens were then heated at 686°K for 1 hr followed by air cooling in order to produce an annealed structure which exhibited a uniform equiaxed grain size of about 4 grains per mm. Tests were run in creep machines fitted with Andrade-Chalmers type of lever arms so contoured as to maintain the stress constant to within 0.05 pct of the reported values. Constant temperatures to *O.l°K were obtained by complete immersion of each specimen in a temperature-controlled and agitated bath of molten KN02-KNOs mixture. Where changes in temperature were involved, the change was effected in less than 2 min by manually replacing one bath by another controlled at the second temperature. Displacements over the gage section were sensed by linear differential transformers, the output of which was autographically recorded. The calculated strain measurements were sensitive to 5x EXPERIMENTAL PROCEDURE The following analyses are based on extensions of the previously announced effect of the temperature on the creep strain,2 namely for a = constant, where e = the total true tensile creep strain for a given applied true tensile stress, t = the duration of the test, R = the gas constant, T = the absolute temperature, Q, = the activation energy per mole for creep which is independent of the stress, / = a function of 8, = and of the stress, and a = the stress. The validity of this correlation for high-purity aluminum is demonstrated in Fig. 1 for temperatures in the near vicinity of 600°K; the activation energy for creep, Q,, which is approximately that for self-diffusion, is insensitive to the applied stress

Jan 1, 1964

INTINERARY ?What is SRI? ? How do we define good corporate social and environmental performance in the mining and petroleum industries? ? Why should you care? MJRA Inc. ? Established in 1992 ? Canadian Social Investment Database (CSID) launched in 1993 ? Jantzi Social Index launched in January 2000 ? created in 2000 SRI is ?the incorporation of social and environmental parameters into the investment decision making process.

May 1, 2002

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

By Rui Xiang Yang, Cong Li, Jia Zeng, Rong Liang Zhang, Wei Zhang, Chao Fan Tang

This research took the roasted products obtained by leaching copper (Cu) refining slag using waste acids and roasting leaching residues with calcium oxide (CaO) as raw materials and used oxidative leaching to extract Cu from roasted products using waste acids. Influences of the leaching temperature, liquid–solid ratio, and sulfuric acid ( H2SO4) concentration in waste acids on the leaching rate of Cu in the oxidative leaching process of roasted products using waste acids were investigated. The unreacted-core shrinking model of heterogeneous reactions was adopted to reveal the leaching kinetics of Cu in the oxidative leaching process of roasted products using waste acids. Results show that the leaching rate of Cu reaches 91.68% when the leaching temperature, liquid–solid ratio, H2SO4 concentration in waste acids, and injected airflow are 80 ℃, 8:1, 1.5 mol/L, and 200 mL/min, respectively. If the leaching temperature is below 80 ℃, the leaching process of Cu is controlled by the solid-film diffusion, and the apparent activation energy Ea is 11.0835 kJ/mol; at a leaching temperature above 80 ℃, the leaching process of Cu is governed by the interfacial chemical reaction, with an apparent activation energy Ea of 42.3183 kJ/mol. The liquid–solid ratio can positively influence the reaction rate constant. The apparent order of the leaching reaction of Cu is 0.632.

Jan 11, 2023

By Florian Kongoli

Minor components and flux additions can modify the liquidus temperatures of multicomponent slags. In industrial practice, slags with various levels of minor components require various flux additions in order to achieve the lowest possible liquidus temperature The prediction and the optimization of these combinations can decrease the cost of the overall process. In this work the effect of several minor components and flux additions such as Al2O3, MgO, and CaO, on the liquidus temperatures of multicomponent iron-silicate slags has been analyzed in terms of a thermodynamic model Various simple isothermal and non-isothermal diagrams are presented. These diagrams can be used directly by the process operators to define the optimum conditions under which the fluxes can be used to achieve the desired slag liquidus temperatures.

Jan 1, 1999

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By E. C. Weichel, J. H. Carpenter, J. C. Detweiler, J. L. Gillson, J. P. Wood

ILMENITE, rutile, zircon, and other heavy minerals are found in small amounts in the sand that covers most of Florida. Small enriched deposits occur on the beaches and coastal dunes. One beach deposit east of Jacksonville was worked during World War I and another near Vero Beach during World War 11. Both ceased operation when the resumption of imports reduced prices.

Jan 8, 1953

By B. Caldwell

"The CompanyCardinal River Coals is jointly owned by Luscar Ltd. and the Consolidated Coal Company of Canada (Consol). The Luscar mine is operated by Luscar Ltd. and is located 40 km south of Hinton near Cadomin, Alberta (Fig. 1). The plant sits on the old townsite of Luscar, Alberta, which was founded in order to develop the coal in 1912 (Fig. 2). Initially, the coal was mined by Luscar Ltd. for heating and steam generation and used quite heavily by the railways for their steam locomotives. In 1955, the mine was decommissioned as the demand for coal for tl1ese purposes had dropped off. In 1969, the mine was re-established by Cardinal River to provide metallurgical coking coal for its customers in Japan. The coal is mined from the 13m thick Jewel Seam by open pit methods at a 10 to 1 stripping ratio. The run-of-mine coal is then cleaned to meet customer demands.The PlantThe clean coal preparation facilities at Cardinal River were extended in 1980 in order to increase the feed rate from 450 t/h to 800 t/h. The extension is a separate plant which can be operated on its own or in parallel with the old plant. In addition, modifications have been made to the fine coal circuit (hydrocyclones added), the coarse refuse circuit, (refuse bucks replaced by a refuse conveyor which backfills a pit), and the fine refuse circuit (solid bowl refuse centrifuges, refuse classifying cyclones, and hydra-rake thickener no longer utilized) since the plant was built in 1969. The plant production of 3 M t per year with a yield of 78% is achieved by first screening and breaking the run-of-mine material to a top size of 1 ½ in. The feed is then slurried, sized, and processed in three different washing circuits. The washed coal is mechanically dewatered, thermally dried, and then stored in a 14 500 t capacity silo or on a 300 000 t stockpile. The fine refuse is thickened and pumped to the same pit to which the coarse refuse is being conveyed"

Jan 1, 2000

By John A. Church

AT a time when the treatment of gold and silver ores by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

Jan 1, 1873

By E. Woodburn, R. P. King, R. Putman

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By John A. Church

AT a time when the treatment of gold and silver ore9 by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966

By Yongyong Gong, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"Microstructure of semisolid slurry of Al-4.5wt.%Cu alloy was investigated with pulse magnetooscillation (PMO) treatment, the results showed that the PMO treatment can refine the crystal structures of Al-4.5wt.%Cu alloy significantly. The discharging frequency of PMO had a great effect on the solidified structure transformation of semisolid slurry of Al-4.5wt. %Cu alloy, and the primary a-Al particles become much finer and rounder with an increase of discharging frequency. However, over a certain discharging frequency, the grains of primary a-Al become coarse.IntroductionOver the last decade, a lot of attentions have been paid on metal rheoforming process [1-4], since it has higher mechanical properties of formed components, strength to weight ratio and age hardenablity. Nevertheless, semi-solid forming is always performed at high solid fractions (40%-60%), so it has the limitation of viscosity, a tends to be difficult to pour semisolid slurry into the hole of the shot sleeve. Therefore, a series of novel semi-solid slurry preparation methods and rheoforming techniques have been invented, such as, semisolid vibration treatment [5], rheocasting [6], pulsed magnetic field process [7], annulus electromagnetic stirring [8], via ultrasonic vibration process [9], equal channel angular extrusion (ECAE) process [l0] and straininduced melt activation (SIMA) process [11].The electromagnetic field is characterized by its effective grain refinement, green, convenient manipulation and without contamination of melt. The mechanisms of dendrite was fragmentation by electromagnetic field have also been largely proposed [12-14]. The broken dendrite arms then undergo a coarsening process to provide the globular structures and obtain much finer and rounder a-Al particles. When compared with other external electromagnetic techniques, Pulse Magneto-Oscillation (PMO) has obtained more fuvors, owing to narrower pulse width and much lower energy consumption. Furthermore, the PMO treatment can reach finer grains with shorter time treatment [16, 17]. This work aims to study the effects of different discharging frequency ofPMO treatment on the microstructure transition of the semisolid slurry of Al-4.5 wt.%Cu alloy."

Jan 1, 2014

By Marcus A. Grossman

THE institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it," All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we should review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks.

Jan 1, 1946

Over and above the technical support arid consulting work described in the preceding Parts of this Volume, ADL staff also provided a wide range of additional technical assistance to the Bureau on an ad hoc basis over the course of the contract, and particularly in 1973. Some of these assignments were on tasks that temporarily assumed a high priority at PMSRC, requiring a fast response, while others were more suited to conventional schedules but on communication and location topics less directly related to those in the preceding Parts. Chapter I briefly describes some of the diverse short-term assignments while Chapters I1through V treat assignments on the other topics. I SHORT-TEXM ASSIGNMENTS A sampling of short-term, fast-response assignments undertaken on mine communications and miner location for PMSRC during 1973 are given below. These assignments included technical reviews, discussions and recommendations related to the theory, experimental data, designs, and hardware implementation of experimental CW and pulse miner location EM transmitters; preparation of technical performance specifications for a miniaturized preproduction prototype CW electromagnetic location transmitter; review of specifications for a seismic signal detection experimental study; participation in technical discussions and experiments with PMSRC and equipment suppliers regarding the UHF radio/radiax-cable communications installation in the Bruceton mine; participation in an informal conference to discuss mine communication and monitoring needs and preferences with representatives of the Bureau, mine operators, and equipment manufacturers; participation in technical discussions with representatives of a U.S. mine operator and CERCHAR* concerning the characterization of faults on trolley lines and means of improving their rapid detection;** recommendation of simple signal, noise, and ground fault measurements on mine phone lines; review of an inexpensive automatic telephone dialer; preliminary discussions regarding the feasibility of adapting and assembling a collection of available telephone industry carrier equipment for installation and test in an operating coal mine; evaluation of a proposed call alert mine paging system; review of hardware designs and future experiments for a mine communication sled; design critique of a proposed six-channel narrow-band FM voice modem for carrier communication on the mine phone line; preparation of technical performance

Jan 1, 1974

By R. P. King

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By C. Walker

Since the 1950's, production of ferronickel from laterites has predominantly been achieved using the Rotary Kiln -Electric Furnace (RKEF) process. The productivities of kilns and furnaces have increased steadily over the years and metallurgical smelters can now rely on a smaller number of high-powered, reliable units to meet production objectives at much lower capital and operating costs per tonne of production. Modem RKEF plants are characterized by one or more process lines consisting of one large kiln feeding one large furnace. The current benchmark is one RKEF line with a high capacity kiln feeding an 80 MW furnace to process approximately 1.3 million tonnes per year of new laterite ore. It is proposed that a single RKEF line comprising one kiln producing 240 t/h of calcine feeding a 120 MW furnace could process 2 million tonnes per year of dry new ore which, for an ore grade of 2% nickel, is equivalent to 36,000 t/y of nickel per line. The plant could also be twinned to double the capacity to 72,000 t/y of nickel. This paper reviews recent developments in kiln and furnace technology, which enable substantial increase in productivity of an RKEF plant. The reduction in the capital and operating costs of a single-line, 2 million tonne of ore per year nickel laterite facility, and accompanying improvement in energy efficiency and environmental performance compared to existing operations, are also highlighted.

Jan 1, 2009

By J. E. Flinn, E. R. Gilbert

Recently, Green reported some high-temperature, 0.60 to 0.89 T3, creep results on unalloyed tantalum. From his study he determined an activation energy of 114 kcal per mole for steady-state creep using the T, differential-temperature method25 for testing. He accounted for the difference between this value and 110 kcal per mole for self-diffusion by the temperature dependence of the elastic modulus, 4 kcal per mole. This reported activation energy is in apparent disagreement with that which can be determined from Green's isothermal data, which we have plotted as log creep rate vs 1/T in Fig. 15. From this figure, it appears that there are two activation energies of -185 kcal per mole at the higher temperatures and -75 kcal per mole at the lower temperatures. It is not obvious that the data can be fitted to a straight line corresponding to an activation energy of 114 kcal per mole. One is led to two possible conclusions regarding Green's study: there are two discrete processes controlling the creep rate from 0.60 to 0.89 Tm or the apparent activation energy is not discrete but continuously increases with increasing temperature. The former speculation would be in closer agreement with the high-temperature creep behavior of tungsten.28 The apparent disagreement between the activation energies determined by the AT and isothermal methods certainly suggests that further study on the high-temperature creep of tantalum is needed.

Jan 1, 1967

This chapter looks at the development and use of the operating budget. This is management's plan of action in the short term, usually one year. The operating budget includes all expensed production costs (i.e., all costs reported as cost of goods sold) but does not include expenditures on capital equipment, which are usually justified using discounted cash flow techniques.

Jan 1, 1999