Search Documents

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919

By Carlos A. Ferreira, Betina Hansen, Marco A. S. Rodrigues, Marcela P. Proença

"Nowadays, the concern with the reduction of industrial pollution has motivated researchers to found out new technologies for treatment of industrial waste. The clean technologies, as electrodialysis, are capable of treating these residues, minimizing the impacts when they are discarded directly on the environment. Membranes of SPS/HIPS, PAniCSA/SPS/HIPS, SPAN/SPS/HIPS were developed using chemical mixture method. Membranes were characterized by Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA) and Scanning Electronic Microscopy (SEM). Membranes were submitted to electrical polarization and to electrodialysis at NaCl and KCl solutions, in order to determine ionic transport through the membranes. Results were compared with commercial membranes. The average percent extraction for Na+ ions obtained by membrane was beyond 20%.IntroductionThe high environmental impact caused by the galvanoplastic industries represents today a world concern(1). In the galvanoplasty, thin metallic layers are deposited on metallic surfaces(2) through chemical methods or electrochemical process. This industrial process presents some disadvantages that limit its utilization, as the generation of toxic effluents containing concentrations of heavy metals usually above the limits allowed for his release in receiving bodies(1), the production of galvanic sludge which is considered hazardous waste and that is very difficult to treat, beyond the high consumption of water (3).Stimulated by the development of new ion-exchanged membranes with high selectivity, lower electrical resistance, and improved thermal, chemical and mechanical properties, the use of electrodialysis in the wastewater treatment has recently gained a broader interest(5). The electrodialysis (ED) is a mass separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution(5). The technique permits the recovery and the reutilization of the waste products from the industrial process, avoiding the discharge of them on the environmental (acting as clean technology)."

Jan 1, 2008

By D. Torrey

CONSIDERING the two great interests of to-day, in iron upon the one hand and steel upon the other, and recognizing with measurable distinctness the peculiar fitness of each for special services to which they are applied, the proposition to unite the two metals in combination, to bring into simultaneous use the peculiar advantages which each offers, has great attractions. The limited success which has been attained by trying to bring about such combinations of the two metals through the use of fluxes in welding, has led to the general adoption of the opinion that an effective union of the two metals is impracticable, or to the view that if practicable it would have but limited commercial value. Such opinions are, I think, premature and erroneous, and having gained some knowledge of the character and value of the "Wheeler process" for welding iron and steel without the use of fluxes, I submit the following observations and opinions of the matter for your information, with the hope of eliciting such a discussion of the subject as it may require. The principle of the invention is to bring the two metals simultaneously to a welding heat in one pile, and then to manipulate it.

Jan 1, 1879

By James A. Nunn

Location Xiaolangdi is located in the Henan province of the People’s Republic of China. The distance between Xiaolangdi and the capital of Henan, Zhengzhou, is about200 km. Xiaolangdi is located on the Yellow River at the end of its big characteristic knee. It can be easily found on the map by locating Luoyang. The closest big city to Xiaolangdi is Luoyang (about 45 km). This city has about1 million inhabitants and is well known also to foreigners for its famous historical past. It has been the capital of China through 10 dynasties in former times. Overview The Xiaolangdi Multipurpose Dam Project is located at the last gorge of the middle reach of the Yellow River. The main purposes of the project are: -flood control, - ice jam control, - sediment control, - irrigation, - water supply, - hydroelectric power generation. The project consists of many structures, these are 10 intake towers, 9 flood &sediment tunnels, 6 power tunnels, 1 underground powerhouse, and 1 zone dearth and rockfill dam with a sloping impervious core, 154m high, with a crest length of 1317m. The powerhouse mainly features 6 turbine and generator units of 300 MW, totalling installed capacity of 1800 MW and annual energy output of5.1 GWH. The total storage capacity of the reservoir is 12.65 billion m³ of which 5.1billion m³ is live storage. Of the Yellow River drainage basin, 694,000 km2 or 92,3percent is located upstream of Xiaolangdi Dam Site. Xiaolangdi is located in a key position for flood and sediment control of the Yellow River. Upon completion, Xiaolangdi Dam and Reservoir will effectively mitigate catastrophic floods, the control level will be increased from the present less than 100-year return period up to 10,000 years. Also, it will reduce severe flooding of the river bed of the lower

Jan 1, 1999

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,' wire of some bcc metals,' and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4'5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

By G. A. Vissac

In the presentation which follows, wash-ability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. Float-and-sink Tests For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve"—a somewhat misleading term—will be considered; Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. New Form of Graphic Presentation The resemblance of the recovery curve ill Fig. 1, or, for that matter, the recovery curve obtained in common practice! to a Power curve is apparent. The general equation of such a curve is Y = axn, where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis! the recovery graph will be a straight line, using the same variables as in Fig. I; namely, the ash con-

Jan 1, 1942

By G. A. Vissac

In the presentation which follows, wash-ability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. Float-and-sink Tests For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve"—a somewhat misleading term—will be considered; Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. New Form of Graphic Presentation The resemblance of the recovery curve ill Fig. 1, or, for that matter, the recovery curve obtained in common practice! to a Power curve is apparent. The general equation of such a curve is Y = axn, where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis! the recovery graph will be a straight line, using the same variables as in Fig. I; namely, the ash con-

Jan 1, 1942

By P. A. Farrar, M. D. Silver, K. L. Komarek

Thermodynamic properties of Hf-0 alloys have been determined from 0 to 25 at. pct 0 between 1000" and 1200°K by equilibrating specimens with alkaline metal oxide-metal vapor combinations. Partial molar-free energies, enthalpies, and entropies of oxygen have been obtained and are conzpared with similar results for the Ti-0 and ZY-0 In continuation of a thermodynamic investigation of the Ti-O and Zr-O systems1 activities of oxygen and lattice parameters of Hf-0 alloys have been deter- system. The positional entropy in all three systems corresponds to an ideal random interstitial solution with one interstitial site per one metal atom. The lattice parameters of hafnium and Hf-O solid solutions have been determined in the range 0 to 20 at. pct O from measurements of Debye powder patterns. mined. All three metals dissolve large quantities of oxygen to form interstitial solid solutions. The phase diagram of the Hf-O system is shown in Fig. 1.' The maximum solubility of oxygen in the cph a phase is considerable (up to 25 at. pct O). The solubility in the high-temperature phase is much smaller. The only stable compound in the solid state is HfO2 which may exist with a certain oxygen deficiency. The low partial pressure of oxygen of Hf-0 alloys required the application of an indirect method. As the most suitable procedure a method, first applied by Kubaschewski to the V-O system,3 was combined with a principle developed by Herasymenko for the

Jan 1, 1963

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

By C. W. Nelson, A. G. Moody

This paper describes the design, equipment selection and onshore fabrication of the largest facilities module ever installed in a single lift in the Gulf of Mexico. Measuring 35.5 x 70.1 x 21.3 m (110 x 230 x 70 ft), the three operating level structure houses Frasch process sulfur mining equipment and weighed nearly 49 million N (5500 tons) during lift. An operating weight of over 74 million N (8300 st) combines with bridge reactions acting on the in-place module and results in a total operating vertical load on the supporting platform deck of about 107 million N (12,000 tons). A Vierendeel truss structural system was selected for framing the module to allow maximum equipment access and routing flexibility for complex, insulated large diameter process piping. Research and finite element analysis of crimp plate siding behavior in shear was carried out during selection of siding type for the module. An interactive design sequence was carried out that incorporated in-place operational criteria, onshore fabrication considerations, complex process equipment requirements, plus load-out, ocean transport and offshore lift analyses. Project schedule dictated that design, procurement and fabrication be fast-tracked with parallel activities accelerated to the maximum extent possible. Design and construction of this largest and most complex module was done concurrently with 52 other components of the project including jackets, decks, process and living quarters modules as well as two 122 x 22 m (400 x 72 ft) sulfur tankers. Total tonnage of steel structures for the project exceeded 90.7 kt (100,000 st). The 5 kt (5500 st) mining module proved the viability and costeffectiveness of larger modules than commonly used in Gulf of Mexico waters. This technical advance can be matched with economic opportunity for other large-scale offshore installations.

Jan 1, 1994

By N. S. Dalal, X. Shi

While it is known that vanadate and related compounds of pentavalent vanadium ( V (V)) exert potent toxic effects on a wide variety of biological systems, the underlying biochemical mechanism is still not fully understood ( 1- 3). One of the pathways is thought to involve the oxidation of NAD ( P) H. Thus, considerable effort has been devoted to finding the mechanism of NAD ( P) H oxidation by Vcvi (1-15). Erdmann et al. (5) first noted that vanadate stimulated the oxidation of NADH by plasma membranes and attributed this effect to a membrane containing NAD(P)H-dependent V(V) reductase. Later studies by Liochev and Fridovich indicated that endogenous superoxide ( 02 ) plays a central role in this reaction ( 4, 12, 13) . They proposed that NAD ( P) H dehydrogenases or oxidases produce 02, which causes VCV ) to stimulate NAD ( P) H oxidation via the following free radical chain mechanism ( 4, 12, 13) :

Mar 1, 1992

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

Discussion of the paper of GEORGE K. BURGESS and SIR ROBERT A. HADFIELD, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 455 to 468. ALBERT SAUVEUR, Cambridge, Mass.-There is a definiteness and finality in the investigations that have been conducted by the Bureau of Standards and in the method of presenting the results that is most satisfactory and refreshing.. A year ago Dr. Burgess and his co-workers investigated the question of critical points in carbonless iron, and they settled the question once for all. No one can now claim that the thermal point A2 in carbonless iron does not exist. At the past meeting of this Institute in Pittsburgh, Dr. Burgess showed the worthlessness of the shrinkage clause. To my mind after his demonstration no one can again claim that the shrinkage clause renders any service. He also showed us that it was a practicable proposition to use pyrometers in steel work in order to ascertain the finishing temperatures of rails. No one can again come before this body and make the claim that it is not a practical proposition. And now Dr. Burgess shows us that steel ingots can be made in a commercial way, practically free from pipe, from segregation, aid from blow holes. It places again before us in a very clear manner the question of piped ingots and of segregation, a question which has been debated for 20 years or more. I know very well the attitude of the standpatters in the matter. They claim that most of the pipe is removed in the discard, and that if a little is left it is so thoroughly welded that it does no harm. I for one am not convinced of the soundness of the argument. I do not believe there is any one present who would claim that, given an ingot free from pipe, free from segregation, and free from blow holes, better rails will not be made out of that ingot than out of the ordinary piped or segregated metal which is used by almost all of our steel mills. In my opinion, if we give our sanction to the casting of steel in the shape of piped or segregated steel ingots, we are guilty. If we give our sanction to the rolling of rails from such metal, we are guilty. It is our duty as experts, as steel makers, and as steel consumers to make and to use the best steel obtainable on a commercial basis, for the manufacture of rails. Now, we have been shown that sound ingots can be produced from which superior rails can be made. If we do not insist upon these sound ingots, then we fail in our duty. I think that the art of casting steel ingots has advanced to such a point that the casting of steel ingots piped and segregated ought no longer to be tolerated.

Jan 5, 1915

By P. C. Hollick

Two marine diamond deposits on concession 2b off Namaqualand along the South African Coast, have been systematically mined over the past year by the mv Moonstar. The two deposits, Smith?s Ulcer and Wedge Point Basin, are comparable in morphology, straddled the same water depths and have similar geology yet have given very different recoveries when compared to their respective grade models. These differences are best ascribed to the different style of mineralisation observed within the two deposits which has been directly controlled by the bedrock morphology. The smith?s Ulcer deposit has been formed in a metagreywacke bedrock displaying a strong north-south trending foliation which dips steeply to the west. Consequently the mineralisation is confined to narrow north-south linear trends with limited lateral extent (less than 5m) making extraction extremely difficult and somewhat variable. RE factors (recovered grade versus estimated grade) for this deposit range from 0.5 to 1.1. The Wedge Point Basin deposit is formed in a micaceous metaquartzite with a conjugate southwest northwest joint set, the southwest lineation being the more prominent, and structural foliation dipping gently to the west. The resultant style of mineralisation is confined to basinal features defined by topographical lows and is fairly lateral in extent (in order of 50m). Extraction of the mineralisation from this deposit is less arduous with recoveries more uniform, RE factors are frequently in the range 2 - 3. This style of mineralisation is more in line with what is to be expected from marine alluvial deposits, the nugget effect of diamond concentration being responsible for the high RE factor. The long narrow linear trends observed in Smith?s Ulcer demonstrably require a specialised approach in successfully sampling, modeling and ultimately mining.

Jan 1, 1998

By D. Pirouzan

It is customary to use more than one stage of flotation to obtain an acceptable level of separation of valuables. Flotation circuit design is usually accomplished by applying empirical rules which usually results in operations not working at their optimum conditions. Given the capabilities of genetic algorithms (GA) in finding an optimum solution in a very disturbed search spaces, they can be used to obtain the desired flotation circuit configuration. In flotation circuit configuration and optimization problem, a combination of metallurgical parameters such as yield and concentrate ash content could be used as the fitness function for the genetic algorithm. The multi-objective nature of the problem justified to use Pareto method to arrive at a set of solutions. The appropriate configuration based on technical or economical considerations could then be chosen. To obtain the fitness function for any given configuration, it is necessary to model every flotation stage. The proposed method was used to find the optimum circuit configuration for a coal washing plant. The objective was to arrive at the highest yield while producing a concentrate with a certain ash content (< 11%). The feed to the flotation circuit was characterized based on the size fractions and their flotation rate constants. Results showed that with a 95% confidence, the absolute difference between the modeled and measured values were 2.9-5.5% for yield and 0.4-1.1% for concentrate ash content. When the proposed GA-based circuit configuration was implemented in the plant, the yield increased from the original value of 57.6% to 65.7% while producing concentrate ash content (10.9%) within acceptable limits. By adding one stage to the current three-stage circuit, it was predicted that the yield could further increase by 3.8% while keeping the quality of the concentrate within the appropriate level. Keywords: modeling, optimizing, flotation circuit configuration, genetic algorithms

Sep 1, 2012

By L. C. Brown, J. S. Kirkaldy

AS part of a program to investigate the diffusive properties of dilute ternary austenites, we have made a determination of the effects of cobalt on the activity of carbon in y iron. Samples of pure iron and Fe-Co alloys were equilibrated at 1000°C in controlled CO-C02 atmospheres, following the procedure of R. P. smith.&apos; The 0.010-in.-thick samples were analyzed for carbon by microcombustion analysis2 to give a set of isoactivity curves. The latter were converted to activity-coefficient (standard state at infinite dilution) plots by combination with Smith&apos;s data&apos; for the activity of carbon in pure iron measured in a CO-C02 mixture. Table I shows the composition of the base alloys used, while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In the notation of Wagner,&apos; the interaction parameter is the second coefficient on the right, Eq. [I] adequately correlates the experimental points for those alloys which were prepared from electrolytic iron by arc-melting (2,4, and 7 pct Co). The results for the 10 pct Co alloy (supplied by Crucible Steel Co.) do not correlate with the others. In fact, the experimental points for this alloy correspond to an interaction parameter of It is possible that the interaction parameter is a function of concentration for large cobalt additions, but we are inclined to attribute the discrepancy to the presence of a significant amount of aluminum added to this alloy for deoxidation purposes (Table I). Preliminary measurements for the system Fe-C-A1 have indicated an interaction parameter of Which implies that the effect of aluminum in solution on the carbon activity is sixty times greater than the effect of an equal weight percentage of cobalt. These observations cast some doubt on the precision of the results of Chandhok, Hirth, and Dulis who used this same 10 pct alloy for their experiments, obtaining an interaction parameter of E = 2.2. There is considerable doubt as to the activity of a plane Fe-C system. Using a CH4-Ha mixture, Smith obtains cg = 6.1 for the effect of carbon on the activity of carbon in austenite, rather than the value of 8.9 given in Eq. [I]. The use of CHa-Ha mixtures has recently been questioned by Kaufman, Radcliff, and cohens who state that there is some possibility that other hydrocarbons are formed. Fortunately, the determination of the interaction parameter is not sensitive to the coefficient of Nc. For example, using the CHI-H2 results we obtain a value which is almost the same as that obtained using the CO-CO, results. The authors wish to thank Mr. E. J. Dulis of the Crucible Steel Co. of America for supplying us with samples of the 10 pct Co alloy used in their original work. Financial assistance from the American Iron and Steel Institute is gratefully acknowledged.

Jan 1, 1963

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023