Search Documents

Papers of Interest The following papers may be of interest to members. APCOM The Thirteenth International Symposium on the Application of Operation Research and Computer Techniques for Decision Making in the Mineral Industries will be held at the Technical University CIausthaI, Federal Republic of Germany, from 6th to 11th October, 1975.

Jan 1, 1975

By Oswald J. Heinrich

THE responsibility resting upon the owners and managers of mines where fire-damp is generated, renders it a matter of imperative duty that a full and correct statement of any explosion that occurs should be given to the public. But such a statement must be based on the testimony of impartial eye-witnesses or trained experts. Then a sad experience may result in the adoption of effective preventive measures. In the absence of any official and professional body of mining experts in the State of Virginia, the writer desires to submit to his professional brethren of the American Institute of Mining Engineers an account of an explosion which recently took place in a colliery under his management, and earnestly desires a thorough and impartial discussion on the facts submitted. Description and Plan of the Mine.-The "Grove" shaft is situated at the nearest point 825 feet from the last old workings upon the Midlothian property, south of the old Pump shaft works. (See Plate III.) The shaft was sunk by the former company, some thirty years ago, to the depth of 622 feet. An incline over 230 feet long, starting in a northwest direction at a depth of 105 feet above the shaft bottom, had been driven to explore the coal on the dip. A return of very small dimensions had been driven round the shaft on the south side, entering the upcast chamber. With the information obtained from the former company that a seam of coal about four feet thick, at a depth of 490 feet, had been found, and with the information obtained by the present proprietor, R. T. Burrows, of Albion, N. Y., by means of two boreholes on the dip west of the old shaft, in both of which workable seams of coal at various depths had been ascertained, the clearing out and thorough retimbering of this shaft were commenced in March, 1873. Borehole No. 1, at a depth of 477 1/2 feet from surface, revealed a seam of coal. This borehole was afterwards carried to a depth of 1140 feet to the granite, without finding any other seam of coal. Borehole No. 3, at a depth of 608 feet, revealed the first coal-seam, 142 feet thick; at 633 feet, the second, 12 feet thick; at 662 feet the third, 1 foot thick, and at 692 feet the fourth, 4 1/2 to 5 feet thick. The borehole was stopped at a depth of 715 1/2 feet.

Jan 1, 1877

By Lan Li, Izaak Williamson

"The efficient separation and storage of CO2 from power plant flue gases can reduce the amount of CO2 released into the atmosphere and mitigate global warming. Potential candidates for industrial applications are solid sorbent materials. Crucial factors to control the efficiency of porous sorbent materials include the framework and pore structure, and the chemical and physical reactivity of CO2 within the pores. Computational modeling approaches, based on density functional theory (DFT) and van der Waals-DFT, have been applied to nanoporous solid – manganese dioxide a-MnO2. We found that the types and charges of cations as dopants in the a-MnO2 and the concentration of CO2 influence the structural features of a-MnO2, which control its CO2 selectivity performance within the flue gases.IntroductionCarbon capture and storage is a technique to separate large quantities of CO2 from power plant flue gases before being released into the atmosphere. Porous solids are a potential candidate as sorbents to “trap” CO2 through chemical or physical adsorption on their porous surfaces[1]. Such separation efficiency is determined by the size and shape of its pores and by the interaction between the porous surface and the gas adsorbates. The incorporation of cations into the pore can act as a means of structural support and alter the pore diameter to be comparable to the kinetic diameter of the gas adsorbate, such as CO2.A porous solid of particular interest for CCS is manganese dioxide a-MnO2, an octahedral molecular sieve (OMS) composed of edge-sharing MnO6 octahedra that are linked into a nanoporous framework[2]. The framework consists of (1×1) and (2×2) tunnels, referred to as OMS-2. Due to the larger tunnel size, cations and gas adsorbates prefer to reside along the (2×2) tunnel axis of the OMS-2. As seen in Figure 1, a potassium cation K+ is located in the (2×2) tunnel, known as cryptomelane-type MnO2. Its pore diameter of ~ 4.6 Å gives it a good CO2 selectivity performance, because the diameter is comparable to the kinetic diameter of 3.3 Å for CO2[3]. Alternatively, replacing potassium K+ with other cations, e.g. barium Ba2+, sodium Na+ or lithium Li+, in the OMS-2 tunnel is of great research interest, due to the effects of their concentrations, types and charges on the CO2 selectivity efficiency and sorption hysteresis phenomenon[2,4]."

Jan 1, 2014

By Mark William Kennedy

"Electric furnaces containing high quantities of slag are applied in many areas of pyrometallurgy, often for smelting or slag cleaning. A variety of ratios or rules of thumb have been employed in the industry for the dimensioning of these vessels, in most cases with no clear technical basis.In this paper, several design guidelines are presented (electrode size, spacing, vessel dimensions, energy intensity, etc.) as an attempt to provide some technical basis for optimal dimensioning.Furnace heat generation is related to side wall copper cooler heat losses, in an attempt to establish a methodical design strategy particularly for minimum electrode to wall spacing for modern furnaces with cooled linings.Issues regarding the true nature of heat production in a slag furnace are discussed with regards to the possible impact on accurate modeling and design.IntroductionSlag furnaces have passed through a number of design 'generations' characterized by increasing energy intensities, improved electrode technologies and advancing development in their physical structure or 'furnace integrity' as shown in Table I f 1]. A 3rd generation furnace using ultra-high-power (UHP) graphite electrodes is shown in Figure 1, as a generic example of the types of physical structures present in modern slag furnace designs [1]."

Jan 1, 2012

By John H. Schloen

"The object of this paper is to review electrolytic copper refining as it was in 1954(1), as it is now in 1984, and to comment on the many improvements which have been made in the last thirty years.In 1954, and even in 1984, the ASTM specification B 115 for cathode copper was 99.90% minimum copper plus silver content and 100% minimum electrical conductivity, IACS standard. However, to meet competition and to satisfy the requirements of the fabricators and the electrical industry, the electrolytic refinery must supply a product of 99.95% to 99.96% minimum copper content, and 101fJlo minimum electrical conductivity.The range of cathode impurities reported by 20 major copper refineries in 1954 are given in Table I.The much more rigid British Specification, DD 78, for high-purity cathode copper, specifies individual elements, as well as groups of elements, as shown in Table 2.The Svenska test has been replaced by a similar procedure which uses 2.r mm diameter wire. The ISO test is the one listed in the DD 78 specification. In Table 3, corresponding values for the Svenska and ISO test s are given for various wire bar coppers."

Jan 1, 1986

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By James Bennett, Jinichiro Nakano, Anna Nakano

Previous empirical research demonstrated that by mixing gasification and metallurgical slags at a specific composition in a CO2 enriched environment, enough exothermic heat would be generated to transform CO2 to CO. The process capacity may be limited by the availability of the slags, however, it could be used to supplement existing energy or chemical production to reduce overall carbon emission. In this study, computational simulations were performed to explore optimal process conditions based on effects of individual slag constituents and thermal input for maximal gas conversion rate, heat production, and volume increase. In simulated conversions of CO2 to CO and H2O to H 2, comparisons were made by varying CaO, FeO, versus V2O3 slag constituents. The result indicated the optimal slag composition may be obtained by appropriate source selection and mixing of gasification and metallurgical slags in order to maximize carbon reduction and/or H2 production.

Mar 1, 2017

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation.

Jan 1, 1981

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

By C. W. Phillips, R. S. Busk

With most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and micro-porosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. Measurement OF Grain Size By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscopc are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Abom, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurcment. The A.S.T.M. recommends that measurement be made by comparison with a standard chart, by means of Jeffries' planimetric method4 or Heyn's intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.5 The chart was constructed by photographing at Ioo diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargemcnt of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By G. F. Balderson

In response to the written contribution made by G. J. C. Young to the above paper, I would like to make the following points. Paragraph 1 The build-up of oxidized coatings on cone surfaces has not been a problem in other applications similar to that at President Steyn. The following companies have commented.

Jan 1, 1982

By J. D. Christensen

In August 1987, we marked the tenth anniversary of the Surface Mining Control and Reclamation Act. Anniversaries are supposed to be times of celebration, and I truly believe that we have something to celebrate on this anniversary. For, after ten years, there has been much progress in the implementation of the surface mining law.

Jan 1, 1988

By Michael J. Burrell

Sands Hill Coal, located in Wellston, Ohio produces coal for steam generation and crushed limestone for the aggregate market in southeastern Ohio. This paper concerns the blasting and production of the limestone which lies between the #5 and #4 coal seams. The limestone bed averages 8 to 10 feet in thickness and is overlain with 17 to 20 feet of shale from the floor of the #5 seam.

Jan 1, 1990

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By S. A. Allen

The Eufaula bauxite district of Barbour and Henry Counties in southeast Alabama covers an area approximately 14 miles long, 6 miles wide at the eastern extremity near the Chattahoochee River, and 10 miles wide at the western end near the east fork of the Choctawhatchee River (see figs. 1 and 2). The long axis of this polygon bears a little south of east.

Jan 1, 1949

Dr. Oldshue has provided a useful summary of a voluminous subject and my task will be to select and direct attention to those areas of mixing theory and practice which are germane to mineral processing in general, and to fine particle treatment in particular. Pulp mixing in impeller actuated reactors occurs in mineral processing in several different applications: (1) emulsification of reagents; (2) mixing pulp with 'reagents as in conditioning for subsequent operations (such as flotation, flocculation or agglomeration) ; (3) high intensity agitation, as in (a) disintegrating and dispersing aggregates, and (b) aggregating particles as in shear flocculation or in selective agglomeration; (4) hydrometallurgy; (5) hydrometallurgy with gas phase (e.g., Arbiter process); . (6) flotation in sub-aeration machines. Attention is invited to 3 above in which two opposite effects can be induced by proper choice of chemical treatment and hydrodynamic conditions. Successful processes for treating mineral fines require excellent aggregate dispersion in order to fully accomplish the liberation stage. Some processes depend further upon selective aggregation following dispersion. The term “dispersion” is often used in different senses which for present purposes will be clarified at the bottom of the next page.

Jan 1, 1979

On Feb. 16, 1948, the Board of Directors of AIME authorized the publishing of "Technical Notes" in METALS TECHNOLOGY. The purpose is to provide prompt publication of very shod items of the following general types: I. Results of short investigations which do not warrant a paper. 2. The conclusions of extensive investigations of insufficient general interest to justify a regular paper. 3. Conclusions arising in the course of an investigation, which, because of interest to others in the field, the author wishes to present prior to completion of the investigation. 4. Pertinent factual comment (not mere argument) on the subject matter of previous ''Notes." Such Notes will be subject to the approval of the Auxiliary and AIME Publications Committees, but can be handled more promptly than regular papers because they need not be referred to readers. 'The recommended maximum length is 500 words; notes in excess of 1,000 words will not be considered for this type of publication. A graph or photograph may be included as part of the note when particularly illustrative. As with regular papers, contributions to the new section should be submitted to the Secretary of the AIME. Please furnish two copies each complete with illustrations.

Jan 1, 1948

By William A. Mitchell

AN X-ray diffraction pattern for "calcined cold precipitated ferric oxide" is reproduced dia-grammatically along with data for other iron oxides by R. C. Mackenzie.1' This pattern, which shows spacings higher than those for any other form of iron oxide, was obtained from material prepared and photographed at several different times over a period of weeks, but later attempts to reproduce the results were unsuccessful, the pattern of hematite being obtained every time.2 In an attempt to solve this problem, the original photographs showing the strange diffraction pattern were examined and a marked similarity to the hematite pattern was noticed, suggesting that the pattern was in fact due to hematite but corresponded to a shorter wavelength of X-rays than the Cu Ka which was assumed to have .been used. The eight strongest lines were provisionally identified with the strongest hematite lines and, by means of the corresponding hematite spacings, the X-ray wavelength was calculated for each line. This gave an almost constant value, with the exception of the innermost line which was somewhat diffuse, and confirmed the presence of hematite. The value obtained, 0.703 ± 0.015Å, corresponds to the molybdenum Ka wavelength. The X-ray tube used was a four-filament demountable tube with a copper target. Other photographs, mostly of soil clays, taken during the same period gave normal patterns of Cu Ka radiation with one exception. This was a calcined soil clay with a high iron content and also showed Mo Ka lines of the hematite structure. The explanation is almost certainly that the copper target was contaminated with molybdenum, but it is not known how this occurred. Specimens of alumino-silicates gave their normal Cu Ka pattern, but as the K absorption edge of iron is a little longer than the Cu Ka wavelength, specimens with a high iron content greatly reduced the intensity of the Cu Ka diffraction lines relative to that of the lines due to the shorter Mo Ka wavelength. The formation of hematite on calcining cold precipitated hydrated ferric oxide3 is thus confirmed. References R. C. Mackenzie: Investigations on Cold-precipi-tated Hydrated Ferric Oxide and its Origin in Clays. Problems of Clay and Laterite Genesis, p. 69, Fig. 4, F. AIME Symposium, St. Louis, Mo. Feb. 19-22, 1951. Published 1952. 'R. C. Mackenzie: Ref. 1. Note added on proof. V. C. Hansen and L. T. Brownmiller: Equilibrium Studies on Alumina and Ferric Oxide and on Combinations of These with Magnesia and Calcium Oxide. American Journal of Science (1928) 5, No. 15, pp. 225-242.

Jan 1, 1954