Search Documents

By Douglas E. Wolfe, Jogender Singh, Robert Miller, Dong-Ming Zhu, Jeff Eldridge

This paper discusses microstructural changes produced by two novel approaches using electron beam physical vapor deposition (EB-PVD) in which periodic strain fields/microporosity was incorporated within the large columnar grains of Zr02- 8wt.%Y2O3 (8YSZ). The traditional columnar microstructure of partially stabilized zirconia has been slightly modified to produce a lower thermal conductive thermal barrier coating (TBC) by periodically interrupting the condensing vapor resulting in microstructural modifications with diffuse or sharp interfaces and morphological changes on the sub-micron scale without changing the composition of the TBC. These microstructural modifications resulted in a 20-30% reduction in the thermal conductivity, 28-56% increase in hemispherical reflectance, improved oxidation cyclic life (over 100%), and better strain tolerance as compared to standard ZrO2-8wt.%Y2O3 deposited on platinum-nickel-aluminide and CoNiCrA1Y bond-coated MAR-M-247 test samples. The TBC with tailored microstructures were examined by various techniques including scanning electron microscopy (SEM), x-ray diffraction (XRD), steady-state laser heat flux technique, and hemispherical reflectance.

Jan 1, 2004

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy ), and the explanation of those facts (geogeny). The facts to observe are: I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. II. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without; massive or thin; the microscopic structure; also whether magnetic or not; soluble or insoluble; fusible or infusible; and the constituent minerals. III. CHEMICAL, that is, the composition of the rocks and of their minerals and their affinities. IV. PALÆONTOLOGICAL, as what kind of fossils are in the rocks,

Jan 1, 1873

By Joginder S. Bhore, Francis M. Keville, David E. Puza, Roger C. Borggaard

A portion of the Massachusetts Bay Transportation Authority's Red Line Extension through Somerville, Massachusetts consists of 1,553cm (5,092 LF) of hard rock tunneling 6.7m (22 ft.) diameter horeshoe, 148m (485 LF) of mixed face tunneling, 7.2m (23 ft.) diameter circular, beneath an active railroad in a heavily commercialized business district. This paper will deal with the excavation of the mixed face area without the use of a shield. It will address the special excavation and support problems encountered during tunneling operations using the floating crown bar and modified spiling methods. Topics covered will include excavation and support methods, cement grouting, compaction grouting, and instrumentation. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnels and Shafts Somerville/ Cambridge, Massachusetts is part of the Massachusetts Bay Transportation Authority's (MBTA) 5.1km (17,000 ft.) Red Line Extension. This extension runs from Harvard Square, Cambridge, to Alewife Brook Parkway, Cambridge through Somerville. This portion (MBTA Contract #091-106) required the excavation and concreting of 1,701m (5,580 LF) of single track twin tunnels consisting of 1,553m (5,092 LF) of conventional hard rock tunneling under 56 residential properties and 148m (485 LF) of mixed face tunneling beneath an active railroad in a heavily commercialized business district. The mined diameter of the mixed face tunnel is 7.16m (23.5 ft.) Access to the tunnel was via the Summer Street vent shaft, and the two Grove Street access shafts where all tunnel excavated materials were removed.

Jan 1, 1981

By S Hapugoda, J Manuel, N Ware, A Dehghan-Manshadi

The effect of titania (TiO2 ) addition on the sintering performance of hematite iron ore has been studied by doping pure TiO2 into a sinter blend. The results of laboratory-scale compact sintering tests confirmed the considerable effect of TiO2 addition on sinter strength and mineralogy. The tumble index measurements confirmed an improvement in the strength of the sinter in response to TiO2 addition. The melting point of the sinter was also affected by increasing the TiO2 content, indicating a possible relationship between coke breeze consumption and TiO2 on industrial-scale sintering of Ti-bearing ores. Analysis of the sintered structures using optical and scanning electron microscopes confirmed a general improvement in the overall pore structure and sinter melt characteristics with the addition of TiO2 to the sinter blend. An important feature of the sinter structure was the formation of a perovskite phase (CaTiO3 ) and an increase in the proportion of this phase in the structure as TiO2 levels increase.CITATION:Dehghan-Manshadi, A, Manuel, J, Hapugoda, S, Ware, N and Donskoi, E, 2015. Effect of titania on the sintering performance of hematite iron ores, in Proceedings Iron Ore 2015, pp 29–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

Here are the details . . . . . of how a $2.5 million research gamble, now backed by five years of intensive development in cooperation with the Chemical Construction Corp. resulted in a hydrometollurgical process that yields pure metal powders from sulphide concentrate - a process that offers potential savings of $2.5 million a year.

Jan 6, 1953

By W. C. Dailey

National Steel Pellet Co. operates eight 8.2-m diameter by 5.5-m long (87- x 18-ft) SAG mills to grind 15.24 Mt (15 million It) of taconite ore per year. Improvements to increase mill throughput, lower steel consumption, lower power consumption, and increase grinding efficiency will be discussed.

Jan 1, 1987

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress,

Jan 1, 1965

By A. Visnapuu

The Bureau of Mines, as a part of its goal to minimize occupational hazards associated with mining and mineral processing operations, has developed and field tested a compact exhaust air muffler for mechanized, jumbo-mounted pneumatic rock drills. The muffler is constructed of 1/8-inch sheet steel and has nominal dimensions of 1-3/4 by 9 by 13 inches. A directed air passage, flexible neoprene baffles, and an expandable slit-type outlet are incorporated to reduce drill exhaust air noise and eliminate muffler icing. Field tests in actual mining operations showed a l5-dbA reduction in exhaust noise and an 8-to 12-dbA reduction in overall drilling noise with no icing problems or decrease in drill performance. Data are presented on muffler construction, laboratory, and field test results.

Jan 1, 1979

By Altair Lúcio de Souza

Foi implantado um software, PCT (Production Control Tool), de integração e coordenação do fluxo de dados entre os seguintes níveis de automação: nível 3, onde se encontram os dados de especificação do produto e sequenciamento de produção, e nível 2, onde se encontram os modelos matemáticos, resultados do processo, interface com medidores e rastreamento da produção. No processo de construção do PCT viu-se um grande potencial de desenvolver outras funcionalidades, devido enorme flexibilidade dessa ferramenta, como gerenciamento da produção, auxílio na inspeção de qualidade e controle estatístico do processo. Isto levou a criação de um sistema amigável de fácil utilização, utilizado tanto pelos operadores da Linha e inspetores de qualidade como também pelos analistas do processo, auxiliando na otimização da Linha de Tiras a Quente da Gerdau.

Aug 17, 2017

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO Zn(g) + COl. This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction 2Fe2+ + ZnO = 2Fe3+ + Zn(g) or 2FeO + ZnO = Fe2O3 + Zn(g) does not occur at an appreciable rate, as is expected from thermodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide concentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon &apos;Yankee Ingenuity&apos;, innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1984

By Michael A. Poling

Ladies and gentlemen, I appreciate this opportunity to be with you, and to share my outlook on the future of Federal coal leasing. I&apos;m told that you wanted the best speaker on this subject in the world. Perhaps it&apos;s a reflection of these trying financial times, but I&apos;m glad you finally agreed to settle for the best speaker your budget would afford. I have been asked to give you some insight on the status of Federal coal leasing, and how the budget problems facing the Department will affect the coal program. So I&apos;ve polished up my crystal ball, and I&apos;ll try to give you a peek at the future. Before I do that, however, let me first go back in time - to when this Administration took office in 1981. We had a coal program then, after a hiatus of ten years. But that program was untested and - for reasons well known to all of you - did not work well in practice once we began operating the program. We went back to the drawing board and redesigned the program so that it can do what it is intended to do. We&apos;ve made the program more predictable. That means that when future lease sales are scheduled, those sales will be reflective and reactive to the need to lease coal. On February 26, Secretary Hodel unveiled a framework for resumption of Federal leasing program activities, ending a more than two-year suspension of regional coal sales. The new program will provide the opportunity to satisfy market demand for acquiring and developing new leases, assure the government of fair market value for its coal reserves, and provide a stable supply of coal for this country&apos;s energy needs. The new program grew out of the Department&apos;s response to recommendations of the Linowes Commission and the Office of Technology Assessment, coupled with a supplemental environmental study. The Linowes Report, issued in 1984, contained 36 recommendations and three Judgments on leasing levels, tract selection, sale procedures, appraisal methods, key statutory and related factors, and organization and management of the leasing program. Major changes in the new leasing program reflect these concerns. We have developed a definition for captive tracts and devised procedures to appraise their value to the adjacent coal or mine owner. Other steps include a coal lease appraisal guide which describes our appraisal methodology and is available to the public. Improvements have also been made in the gathering of lease assignment information to help in estimating the value of potential lease tracts. To improve market analysis, a three-tiered system will be used to ensure that steps of the lease sale decision process are undertaken in the context of coal supply and demand. Regional Coal Teams will thus have the advantage of long range, regional and tract specific market studies to help them determine whether sufficient demand is expected first to warrant the initiation of activity planning, then to set regional leasing levels, and finally to actually offer specific tracts for lease sale. Sale procedures will also be improved in many ways to encourage competition, improve the chances for receiving adequate bids, and to evaluate whether bids represent fair market value. We made additional modifications to the program in response to the OTA recommendations. Regional Coal Teams have been given a larger role in recommending key decisions concerning the amounts of coal to be studied and the actual selection and scheduling of tracts for lease sale. These recommendations will be accepted unless the Secretary can cite an overriding national interest factor, or a governor&apos;s request to modify the recommendations. Smaller, more frequent sales will be held, to better judge market conditions and prevent over- or under-leasing. Public participation guidelines have been written, to document all opportunities for the public to comment at various stages in the planning process. We also decided that resource management plans prepared after the passage of FLPMA in 1976 must be completed, in order for a new round of lease sale planning to begin. The BLM will also beef up its procedures for consulting with affected Federal agencies during the planning process, to assure that the purposes and values of those agencies are considered and factored into land use decisions. To assure consistent use of an adequate data base in coal lease decision-making, Regional Coal Teams will develop standards and guidelines for data adequacy, and document the use of these standards. These procedures will also be applied to the unsuitability criteria screening process. Thus, the new leasing system announced by Secretary Hodel: is fully responsive to recommendations made by the Linowes Commission and the Office of Technology Assessment for improving environmental planning and fair market value procedures; gives the regional coal teams a major say in determining leasing levels, and on the timing,

Jan 1, 1986

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By P. Ramachandraraa, T. R. Anantharaman

THE technique developed by Duwez, Willens and Kle-ment&apos; for rapid solidification of molten alloys in small quantities by ejecting them on to a highly conducting substrate with the aid of a shock wave has come to be known as "liquid quenching" or "splat cooling" in literature and has already been applied to alloys of many binary systems.&apos; The very high cooling rates of the order of l060 to 1080 per sec obtained in this technique and the consequent drastic undercooling of the melt have led to such striking results as formation of new amorphous and crystalline metastable phases and extension of solid-solubility limits in many alloy systems. The cooling rates in these experiments can, however, be neither accurately measured nor effectively controlled and hence the occurrence of either more than one metastable phase or appreciable differences in constitution in splat-cooled alloys of the same composition cannot be ruled out.3 In fact, workers in two laboratories have reported formation of two different cubic metastable phases in liquid-quenched Au-Si alloys containing 17 to 20 at. pct si.4,5 The present note deals with some new and interesting results obtained in a Ag-21 at. pct Ge alloy and a Au-27 at. pct Ge alloy subjected to the liquid-quenching treatment at different cooling rates. Two alloys of nearly the same composition had earlier been rapidly solidified by the standard "gun technique" in the same laboratory and shown to solidify in nonequilibrium structures, viz., an hcp phase (a = 2.987Å;c =4.718Å) in the Ag-Ge system6,7 and both hcp (a = 2.885Å; c = 4.754Å) and tetragonal (a = 11.627A; c = 22.491Å) phases in the Au-Ge system.3 Apart from different substrates (copper and stainless steel), different melt temperatures (50º to 500°C above the liquidus), and different capillary sizes (0.4 to 1.5 mm diam) in the "gun technique", slower cooling rates of the order of l050C per sec were also obtained in the present work by replacing the substrate by water at room temperature in a modification of the technique due to Olsen and Hultgren.8 No attempt was made to measure the cooling rate in any experiment. The products varied from fine powder (>40 pct by wt—200 mesh) obtained by quenching in water to thin flakes and foils (11.0 sq mm to 4.0 sq cm) produced by splat cooling. They were subjected to the Debye-Scherrer method of X-ray examination in each case. In case of the Ag-Ge alloy, in addition to the expected metastable hcp phase,6 a coexistent tetragonal phase (a = 5.093,Å; c = 7.009Å) was detected in some experiments. Eight weak X-ray reflections from this phase could be identified, two of them being the same as reported earlier.7 With increase in the cooling rate, the dominant hcp phase seems to be first accompanied by traces of silver or germanium and then either homogeneous or mixed with traces of this new tetragonal phase. The splat-cooled Au-Ge alloy showed generally the expected hcp and tetragonal phases,3 but sometimes traces of germanium were also present. Further, two new tetragonal phases with the following lattice param ters could be clearly identified in samples quenched

Jan 1, 1970

I am sure that you are- all familiar with Airborne Magneto-meter Surveying so I shall-spend only a brief moment describing the instrument and techniques and the remainder of the allotted time-on-modern-application-of the instrument.The Airborne Magnetometer used by Aero Service in AUstralia-was designated by Gulf Research and implements the saturable-core flux-gate--principle. The first magnetometers developed&apos;weremagnetic-balances and depended on the counter-torque principle but these required a stable platform and hence are not applicable to airborne surveying. Other methods include the induction methods, the Hall Effect methods, magneto-striction methods., Deflectioh. of,free.electrons, the proton-precession methods.Some: of these are applicable to airborne surveying. As a matter of-fact the nuclear precession magnetometer is the one generally used in the Satellites because it has been miniaturized most successfully.The Gulf Magnetometer is the one most generally used in mineral and petroleum exploration because its sensitivity is sufficient for the problem and-data and instrument techniques have been worked out and standardized.

Jan 1, 1962

In connection with the presentation of his paper in oral abstract, Mr. Hansell exhibited samples of briquettes, showing their porosity, and the change of surface produced by burning. Alfred H. Cowles, Sewaren, N. J.—I am familiar with this furnace, and I wish to point out that the larger it is, the greater is its efficiency, and the longer its life. In Europe, experiments have been made with small, short furnaces of this character, accommodating narrow cars; whereas Mr. Hansell says that there is in this country a furnace 180 ft. long .and 10 ft wide. The American furnaces, moreover, differ in design from those used in Europe; and we may expect from these larger furnaces not only greater efficiency, but also greater durability —the latter advantage being due to the fact that, in these large furnaces, projecting brick walls of greater thickness can be provided, to prevent the heat from attacking the sides of the cars, by means of bricks which, over-reaching these iron surfaces, furnish a protective cover to them. In other words, in these

Jan 1, 1913

Pier, well cap and steining junction is a complicated 3-d re-ion. The prevalent design procedure for the pier, well cap and steining in isolated manner is not rational. In absence of an integrated approach for design of the junction structure, the well cap is designed uneconomical and at the same time pier and steining are left relatively unsafe. Strut-and-Tie Model based design is a simple solution to this problem. An example illustrating design of the junction structure using STM is presented. On comparison of the outcomes of the STM based design with the prevalent design, the following anomalies are found: i) For smooth flow of forces, length of pier at its base should preferably be made equal to the outer well diameter, ii) STM based design for the pier is more rational, economical and safe. iii) Due to presence of hoop stress, as indicated by the STM, the steining concrete in a depth of p times outer diameter of the well from the well cap level should be limited to M15 grade, iv) STM based design for the steining is more rational, economical and safe.

Jan 1, 1996