Search Documents

By W. T. Wertman

A research program to aid development of better petroleum-recovery technology is in progress at the Appalachian Experiment Station, Bureau of Mines, Morgantown, W. Va. The work is part of the overall effort of the Federal Bureau of Mines to effect true conservation of the Nation's natural resources. Knowledge of the magnitude of the interstitial water content of oil-bearing formations is important to petroleum-reservoir engineers because of the influence of water on fluid flow during oil production and because of the significance of water volume in oil-reserve evaluation. Such information on Appalachian oil-bearing formations is needed to aid in planning secondary oil-recovery projects. Generally, the interstitial water content of oil sands can be estimated by one or more of the following methods: Analysis of cores obtained with oil-base drilling fluid, electric logging, restored-state or capillary-pressure tests, centrifuge tests, evaporation tests, or mercury-injection tests.

Jan 1, 1959

By S. A. Hoenig

In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in [Fig.1]. Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in [Fig. 1]. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 /MI (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 µm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform.

Jan 1, 1985

EDWARD B. GRUBB, Burlington, N. J.: In connection with the discussion relative to the effect of vibration upon the molecular structure of wrought-iron, I would like to call your attention to the following extracts from a work by William

Jan 1, 1897

ALASKA Established November 19, 1947 Meets fourth Monday of each month at Fair¬ banks, Alaska J D CRAWFORD, Chairman BRUCE I, THOMAS, Vice-Chairman C D JERMAIN, Vice-Chairman for Southeastern Alaska EARL H BEISTLINE, Secretary-Treasurer Box 265, College, Alaska

Jan 1, 1952

By Alissa Lockett, Chris D. Breeds

Central Water Integration Project (CWIP) Segment 5-1 is the most critical segment of a regional water supply project that transfers groundwater from Burleson County to northern San Antonio, replacing over 20% of that City’s water supply with a new source. CWIP Segment 5-1 included three tunnel reaches totaling 10,350-ft and 5 shafts that were constructed inside the City in an area known to contain large karst features. This paper describes site work used to investigate the alignment for karst features, manage potential environmental impacts, develop the contract package required for mitigation and the means and methods used to mitigate the large karst features that were encountered.

Dec 1, 2022

By M. J. Sinnott, H. B. Probst

AN extensive survey of the factors which affect austenite grain growth has already been made.' These factors are temperature, time at temperature, rate of heating, initial grain size, hot-working, alloy content, ofheating,initialand rate of cooling from the liquidus-solidus temperature. In the present work, a vacuum-melted temperature.electrolytic iron was used and the variables studies were temperature, time at temperature, and prior ferrite grain size. Other factors were maintained constant. The iron used in this study was vacuum-melted electrolytic iron of nominal composition of impurities of 0.07 wt pct. It was supplied as a ½ in. round cold-drawn bar. This iron was tested in three conditions: as-received, annealed 6 hr at 1200°F, and annealed 6 hr at 1600°F. Samples were ? in. disks cut from the bar. The prior anneals were carried out in vacuum and the isothermal treatments were carried out in vacuum-sealed Vycor tubing. The thermal etch technique was employed to determine the austenite grain size. Prior to sealing the test specimens, one surface of the sample was polished metallographically. This surface, after heating, was examined to determine the austenite grain size, since the austenite boundaries are revealed by thermal etching. This is essentially the only technique available for measuring the austenite grain size of low carbon steels or pure irons without altering the composition. It has been shown to yield results that are in agreement with other methods used for determining austenite grain sizes.' The specimen size was quite large compared to the grain size measured, so inhibition of growth due to size effects is probably negligible. After vacuum sealing, each sample was placed into a furnace at temperature and at the completion of the run was quenched into a mercury bath. The growth temperatures used were 1700°, 1800°, 1900°, and 2000°F controlled to -~10"F. Growth times were varied from 10 to 240 hr. The long times were used in order to eliminate the nucleation and growth effects occurring during the initial transformation. Time was measured from the introduction of the capsule into the hot furnace to the time of quench. Grain-size measurements were made with the use of a grain-size eyepiece of a microscope. By determining the number of grains per square millimeter at X100 and taking the square root of the reciprocal of this number, the average linear dimension of the grains was determined. Figs. 1 and 2 are plots of these data as a function of time and temperature for the various conditions investigated. The variation of D, the linear dimension of the grains, was assumed to follow the equation3 D = A tn. The curves of Fig. 1 were obtained from the data by the use of the least-squares method of analysis. Fig. 1 is for the growth of the as-received stock and Fig. 2 is for growth after prior treatments. Differentiating the foregoing equation gives an expression for the rate of growth dD/dt = G = nAtn-1 = nD/t. Both D and G as functions of t are given in Table I. It should be noted that G is a function of time; the growth rate is rapid at early stages and decreases with increasing time. Since increasing temperature increases the growth rate, it has been common practice to use the empirical relationship G = Go e-Q/RT to relate temperature to growth rate. The growth rate customarily has been taken at constant values of D on the basis that the rate of growth is related to the boundary surface tension and this is measured by the curvature of the boundary. At constant D values, the growth rate is a function of time and temperature. The growth rate can be related however to temperature at constant time, and this has the advantage that under these conditions the growth rate is a function only of temperature. Obviously the Q values, activation energies, obtained for each assumption will not be the same and the question of which is the more correct is a moot one, since the assumed exponential relationship in either case has no particular theoretical significance. By plotting G, at constant grain size, vs 1/T, the activation energy over the temperature range of 1800" to 2000°F is found to vary from 30,000 cal per mol at the smaller grain sizes to 50,000 cal per mol at the larger grain sizes. The 1700°F data do not correlate with the data at higher temperatures. The activation energies for the 1200" and 1600°F prior annealed materials were calculated as 50,000 and 62,000 cal per mol, respectively, using the reciprocal time to a given grain size as a measure of the growth rate. Plotting G, at constant times, vs 1/T yields an activation energy of 12,300 cal per mol for the tem-

Jan 1, 1956

By S. I. Freedman

Coal-oil mixture (COM) combustion technology is regarded by the Department of Energy as near term, and potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers, into blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally-acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1978

By Rafael Wilson Soares Ladeira

Realizar manutenções preditivas de forma cada vez mais assertiva é um dos benefícios da atual evolução dos sistemas produtivos industriais conhecida como Indústria 4.0. A Sotreq - revendedora Caterpillar - oferece um serviço de análise de fluidos a partir da coleta periódica para máquinas operantes em campo. Com os resultados das medições, especialistas atribuem às amostras um nível de criticidade, justificativas e recomendações. Neste trabalho propõe-se uma solução que aumentou a eficiência desse processo através da utilização de modelos de Machine Learning treinados com as análises já realizadas que automatizam a classificação e a geração do texto de diagnóstico para novas amostras. As predições do sistema foram consideradas bem sucedidas, com métricas de sensibilidade e especificidade acima de 88%.

Oct 30, 2017

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By Charles W. Merrill

THE INDUSTRIAL strength and the security of the United States require an adequate, dependable, and continuing supply of raw materials, of which minerals constitute an indispensable segment. With an expanding population, a rising standard of living, and the instability inherent in a constantly changing international situation, the mineral supply outlook is a major national concern. Structures, roads, and machines are built largely of mineral products; the energy to heat the structures and to power the machines is derived mostly from minerals; agricultural out-put is sustained with the aid of mineral fertilizers; and the Nation's economic and military security both are founded ultimately on its ability to obtain and utilize essential metals, nonmetals, and mineral fuels.

Jan 1, 1965

By Roland Kammel, Takeo Oki

A suspension electrolysis method has been developed which enabled a direct anodic extraction of zinc from zinc sulfide concentrate and simultaneously oxidized sulfide sulfur to elemental sulfur. The investigation was performed in a laboratory-scale electrolytic cell, where the zinc sulfide concentrate particles (chemical composition in weight percent: 61.1% Zn, 2.3% Fe, 30.6% S, 3.4% SiO2 were suspended with or without graphite powder in a dilute sulfuric acid electrolyte. The main parts of the cylindrical electrolytic cell are shown in [Fig. 1]. The cathode (1), a rod of aluminum, is set at the center of the cell. The anode (2), which consists of four plates, is mounted on the inner face of the cell wall. Both PbO2(Pb) and graphite anodes were used. The cathode compartment (3) is separated from

Jan 1, 1976

By J. B. Hiskey, X. H. Jiang

The extraction of gold from chloride solutions by ion exchange is examined. It is shown that at initial gold concentrations between 1 - 5 ppm, 20 g/l C1- and pH 5, the kinetics of loading on weak base resins are slightly slower than those observed with activated charcoal. Equilibrium loading of auric chloride varies considerably as a function of pH from one resin to another. For all of the resins studied, nearly complete gold extraction was achieved between pH 2 and pH 6.5. Sodium hypochlorite was found to exhibit a slight effect on the equilibrium loading of gold chloride.

Jan 1, 1990

By Y. W. Chung, W. I. Chia

"The interaction of water vapor with single crystal Ni3(Al,Ti) and polycrystalline Ni3Fe, with and without the presence of oxygen, has been studied with Auger electron spectroscopy, photoemission spectroscopy, thermal desorption and isotope exchange. Water dissociates to produce atomic hydrogen above 200 K on both Ni3(Al,Ti) and Ni3Fe surfaces. For Ni3(Al, Ti), the reaction is structure-sensitive. Pre-adsorbed or co-adsorbed oxygen on Ni3(Al,Ti) and Ni3Fe significantly suppresses hydrogen production due to water dissociation. This suppression process occurs more efficiently on Ni3Fe than Ni3(Al, Ti).IntroductionOrdered intermetallic compounds such as aluminides, silicides and titanides are very attractive for structural applications at high temperatures. This is because these intermetallics tend to form adherent oxides in oxidizing environments which protect the base materials from excessive oxidation and corrosion. In addition, they have low density, relatively high melting points and good high-temperature strength. However, the moisture in air severely embrittles many ordered intermetallics such as FeAl [1-3], Fe3A1 [4,5], C03Ti [6,7], (Co,Fe)) V [8], Ni3Si [9], Ni3(Si,Ti) [10], Ni3(AI,Mn) [Ill, and Ni3A1 [12-14], resulting in low 'ductility and brittle fracture at room temperature. Recent studies by Liu and coworkers (see review by George and Liu [15]) provide a qualitative description of the mechanism for this moisture-induced embrittlement. During elongation testing, cracks are formed, thus exposing fresh alloy surfaces. One or more active components of the alloy react with water vapor in the environment to produce atomic hydrogen which penetrates into crack tips and causes hydrogen embrittlement. This is similar to that proposed for moisture-induced embrittlement of aluminum alloys [16]."

Jan 1, 1996

By John H. Schilling

The Gabbs magnesite-brucite deposit is unique in size and is one of two magnesite deposits being exploited in the United States. It is near the town of Gabbs, which is one hundred miles southeast of Reno, in west-central Nevada. The brucite was discovered in 1927; the magnesite was found while exploring the brucite. During World War II, more than 80,000 tons of magnesium metal was produced from about 900,000 tons of magnesite ore mined from these deposits. An additional 5,000,000 tons of magnesite and 1,000,000 tons of brucite have been produced for use in making magnesia refractories and chemicals. Basic Inc., presently the only producer, mines 1.5 ± 0.25 million tons of ore and waste annually using high-selective open-pit rriethods; the ore is up-graded, calcined, and processed into a variety of products. Known reserves of highgrade (less than 5 per cent CaO) magnesite ore total more than 25,000,000 tons, and there are larger tonnages of lower-grade material; brucite reserves are small. The magnesite and brucite are in generally west-dipping dolomite of the upper member of the late Triassic Luning Formation, in the over-riding plate of the Paradise thrust fault. A great variety of dikes and a stock of Cretaceous granodiorite intrude the Luning Formation in the vicinity of the magnesite-brucite deposit. The magnesite bodies are scattered over an area of about a square mile around a prong of granodiorite which extends north from the stock. The brucite is mainly in two bodies in contact with the prong of granodiorite; at the surface and along deeper cracks the brucite has weathered to hydromagnesite and artinite. In the area of magnesite-brucite mineralization, much of the dark, fine-grained, schistose, regionally-metamorphosed dolomite of the Luning Formation has been marmorized to a lighter-colored, coarser-grained, massive dolomite that is intergrown in varying proportions with the magnesite. The magnesite and marmorized dolomite can not be distinguished visually. In addition to the two varieties of dolomite, the gangue in the magnesite and brucite bodies mainly is the various varieties of dike rock, serpentine and a variety of other "contact" minerals, and "post-ore" dolomite and calcite. The magnesite ( and recrystallized dolomite) is believed to have formed by the hydrothermal replacement of the regionally metamorphosed sedimentary dolomite; alternatively it has been suggested that the magnesite is sedimentarv and formed contemporaneously with the dolomite in an embayment of the Triassic sea. Because all the igneous rocks exposed in the immediate vicinity of the magnesite deposits appear to be younger than the magnesite, the ore-forming solutions are thought to be related to a somewhat older granite which crops out elsewhere in the area. The brucite is the result of contact-metasomatic replacement of magnesite during the emplacement of the granodiorite stock.

Jan 1, 1968

By P. Crowther, G. J. Lamprecht

The solubilities of silver, zinc, and cerium in liquid sodium, in the temperature ranges 100 to 270°C, 190° to 550°C, and 120" to 460°C, respectively, have been determined. From the solubility data the heat the entropy the partial molal enthalpy of mixing the excess entropy and the partial molal free energy of solution for the systems Nu-Ag and Na-Zn have been calculated. For the system Na-Ce the observed negative is discussed in terms of the solubility of the oxide Ce2O3. In an earlier publication the results obtained in the study of the solubility of tin' in liquid sodium are presented, as well as the detailed analytical procedures used. 1) REAGENTS Spectroscopically pure metals as supplied by Johnson Matthey and Co, were used to produce the following tracers: 253-day Ag110, 245-day zn65, and 325-day ce141. The tracers were prepared by irradiation in a thermal neutron flux of 4 x 10 13 neutrons cm-2 sek-1. To obtain a uniform amount of the required specific activity, needed for each solubility experiment, the radioactive metal was diluted with the corresponding inactive metal, by melting them together in an inert atmosphere. The liquid sodium used contained 11 ±2 ppm of O,1 determined by the vacuum distillation method.' The oxygen was assumed to be present as the oxide NaD. 2) THE SYSTEMS: SODIUM-SILVER AND SODIUM-ZINC Plots were made of the log of the mole fraction of silver, Fig. 1, and of zinc, Fig. 2, dissolved in the liquid sodium vs reciprocal absolute temperature. The equations for the solubilities, based on the least-squares fit to each plot, are: where Xi is the mole fraction metal dissolved in sodium, T is the absolute temperature, and s is the standard deviation in the value of log Xi. The heats and the entropies lution were calculated from the solubility data by In neither of the two cases was any intermetallic compound formed between sodium and the solute metal as was the case for tin.' Thus, for the silver and zinc systems the pure metal was taken as the reference phase. Since the solids in equilibrium with the liquid sodium were the pure metals, one can calculate the partial molal enthalpy of mixing and

Jan 1, 1969

By G. D. Rieck, M. M. P. Janssen

Chemical diffusion coefficients and heats of activation for diffusion in the NizAh fy), NiAl (6), and Ni3A1 (E) intermetallic phases and the solid solution of aluminum in nickel (( phase) were calculated from layer growth experiments. No finite diffusion coefficient for the NiAl3 ((3) inter metallic phase could be calculated. The values of the diffusion coefficients are dependent both on the method of calculation and the type of diffusion couple. The heat of activation for diffusion in the y phase was found to be 47 kcal per mole in the temperature range oj 428" to 610°C. Heats of activation of 41, 12, and 48 kcal per mole were found for diffusion in the 6, E, and ( phases, respectively , in the temperature range of 655" to 1000°C. Experiments with markers in the diffusion zone demonstrate a very pronounced Kirkendall effect. It appears that only aluminum atoms take an active part in the diffusion process during the formation of the 0 and y phases at temperatures of about 600°C. During the formation of the 6, E, and < phases at higher temperatures only nickel atoms are moving. It is suggested that the great stability of the intermetallic compounds in the Ni-A1 system governs the Kirkendall effect. SOME factors controlling layer growth during inter-diffusion in the Ni-A1 system (phase diagram, see Fig. 1) were studied by Castleman and Seig1e.l&apos;~ They found the NiA1, ((3) and NiAl3 (y) intermetallic compounds to appear in the diffusion zone of Ni-A1 couples at annealing temperatures of 400" to 625°C; the NiAl (6) and Ni3A1 (E) intermetallic compounds appeared in y-Ni couples at annealing temperatures of 800" to 1050°C. These authors carefully examined metallographically Ni-A1 couples after 340 hr annealing at 600°C. Besides the (3 and y phases they found very thin layers of the 6 and E phases. ~n~erman~ and Castleman and Froot4 observed a much more rapid growth of the 5 and E phases at 600°C in Ni-A1 couples in case a crack was present at the /3-A1 interface. Numerous layer thickness measurements carried out by Castleman and Seigle on the y phase prove that the layer growth of this phase obeys the parabolic law after a certain transient period. From this they concluded that the layer growth of the y phase is controlled by volume diffusion. The growth of the 13, 6, and E phases appeared to be volume-diffusion-controlled also. The authors estimated that at 600°C and at atmospheric pressure Dp was 1.8 x lo-"ll sq cm per sec, D, 9.1 x 10" ™ sq cm per sec, Qp 27 kcal per mole, and Qy 31 kcal per mole. The present work was carried out to obtain more quantitative data about the kinetics of growth of the phases of the Ni-A1 system and the reactions that occur during the formation of these phases. Because in this system the diffusion process results in the formation of several distinct intermetallic compounds, the current term reaction diffusion is used in the title of this paper. In order to obtain layers of the fl phase compound of uniform thickness, a new technique for preparing diffusion couples was developed. The kinetics of growth of the y phase in 6-Al, E-Al, and Ni-A1 diffusion couples was studied at different temperatures. The kinetics of growth of the 6, c, and ( phases in Ni-y, Ni-6, and Ni-c diffusion couples was also studied at different temperatures. The calculation of the diffusion coefficients Dp and Dy by Castleman and Seigle are critically considered in this paper; by means of a revised method of calculation more reliable val-ues of , and Dg were found. These values are in good agreement with the values of the diffusion coefficients obtained by the method of Boltzmann-Matano. From the temperature dependence of the diffusion coefficients the heats of activation for diffusion were calculated by means of an Arrhenius-type equation. The investigation of the Kirkendall effect has been used to obtain information about the ratio of the intrinsic diffusion coefficients of the separate atoms5 and the mechanism of diffusion. Moreover porosity as a result of a distinct Kirkendall effect would be of practical importance in connection with the bonding of diffusion coatings. The analyses of the diffusion couples were carried out by metallographic methods. The values of the concentrations at the phase boundaries and the concentration profile in each of the phases, which are needed for the calculation of diffusion coefficients, were obtained by electron-pro be X-ray microanalysis. EXPERIMENTAL PROCEDURE A) Materials for Diffusion Couples. The intermetallic compounds 6 (50 at. pct Ni) and E (74 at. pct Ni) were prepared from the pure metals by high-frequency induction melting in argon atmosphere. Use was made of aluminum wire (99.99 wt pct Al) and nickel sheet (99.95 wt pct Ni). The 6 and E phase melts and the nickel shiet (thickness 0.1 and 0.5 mm) used for preparing diffusion couples were annealed for 64 hr at 1200°~ for homogenization and grain coarsening (final crystal size 1 to 3 mm). composition and homogeneity of the intermetallic compounds were checked by mi-crohardness measurements and X-ray diffraction. From the 6 and E phase melts discs of 0.5 mm thickness were prepared by means of a water-cooled rotat-

Jan 1, 1968

By Verya Nasri, Behrouz Esmaeilkhanian, Mohammad Motallebi

The Mount Royal Tunnel (MRT) is a 100-year-old railway tunnel located in Montreal, Canada. The tunnel is approximately 5 km long, 8.7 m wide and 5.5 m high, with a constant 0.6% grade. This existing tunnel will be used by the new Montreal light rail transit network, Réseau Express Métropolitain (REM). This requires the tunnel to be inspected, rehabilitated and made compliant to the recent safety standards. This paper presents the details of the structural inspection and rehabilitation of the tunnel along with the repair methods, addition of a center wall as well as the enlargement of the tunnel section.

Jun 13, 2021

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire&apos;s location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.

The Inspiration ore body was discovered in 1904, but a 50 -ton mill which was installed to treat the disseminated copper ore promptly failed. The original Inspiration Company then gave way to another, backed by W. B. Thompson, which found 40 million tons of ore. Control then passed to Anaconda and Dr. Louis Ricketts took charge as consulting engineer. He abandoned the mill which had been partially built (to the horror of the stockholders, according to Ira Joralemon) and spent a year and a million dollars experimenting with flotation. The first large copper flotation plant was then built and recovered 50% more copper than had previous gravity mills. It, of course, was highly successful and became the forerunner of modern flotation plants. Inspiration is distinctive as the first fully integrated copper operation in the United States. Three open pits supply sulfide ore to the concentrator and mixed oxide and sulfide ore to a vat leaching and electrowinning operation with leached ore also being sent to the concentrator. In addition, dump leaching supplies pregnant solution for scrap iron precipitation. Inspiration has recently constructed an electric furnace smelter and also operates a continuous casting and rod plant. The new primary 54 in. by 74 in. crusher was completed in May of 1972 and replaced an older unit which was in the way of the open pit development. It is of an unusual circular silo design, which permits dumping 0 from two positions at 90 from each other. One dumping position is in line with the spider, while the other one is at right angles to it. A box girder splitter bar hung from the dump pocket slopes downward from the second dump point, across the spider cap, and rests on the pocket bottom. This splitter was not installed to protect the spider but was to aid in distributing wet ore being dumped from that position to both sides of the spider. Any large amount of wet ore delivered to one side of the spider would pack in the crusher cavity. The round front wall of the 18 ft (5.5 m) deep pocket is unlined except for light steel protection at the top, while the straight back wall is lined with vertically positioned railroad rails. Water for dust suppression is sprayed into the pocket through a cluster of 3/8 in. (9.5 mm) nozzles at the back of the pocket. About 5 gpm (19 lpm) of water are mixed with 90 psi (620 kPa) air upstream of the nozzles to produce a fog which is effective in dust control. The 54 in. Allis -Chalmers gyratory is placed mostly within one quadrant of the circular enclosure to permit placement of the apron feeder on the lowest level in the proper position to transfer crushed ore to the

Jan 1, 1978

By E. S. Machlin

The possibility that formation of voids under creep-rupture conditions may take place by the condensation of vacancies has been investigated theoretically. It has been concluded that nucleation of voids under creep-rupture conditions by vacancy condensation is highly improbable. However, growth of pre-existant voids by vacancy condensation is probable. A number of predictions made in this theory have been verified by the data. It has been predicted and checked that the product of rupture life and steady-state creep rate for preannealed metals and single phase alloys is an approximately invariant quantity, independent of stress, temperature, and atomic number for a given type structure. The direction of the effect of cold work on this product has been predicted and found in agreement with experiment. A number of experiments to evaluate the vacancy condensation mechanism further are described. SEVERAL papers have appeared recently which speculate on the origin of voids formed at grain boundaries under stress.&apos; &apos; The object of this paper is to examine quantitatively the proposition that the voids produced in a creep test are a result of vacancy condensation. A result of this paper is a theory of creep-rupture. Void Nucleation Application of standard nucleation theory" to the problem of void nucleation leads to the following conclusions: 1—Homogeneous nucleation of voids requires a supersaturation ratio (concentration of vacancies in supersaturated to that in saturated solution) of 400 for a reasonable surface energy of 1000 erg per cm-and 1.4 for the improbably low surface energy of 10 erg per cm. 2—Heterogeneous nucleation of voids at plane interfaces between two phases requires a supersaturation ratio of 2.5 for a typical contact angle of 145 3-—Void nucleation about a solid particle may be accomplished at a supersaturation ratio of 1.17 for a typical value of work of adhesion? of 60 erg per The work of adhesion is the surface work 10 replace two solid-vauor surfaces by a solid-solid interface. enr &apos; between an oxide and a metal in the presence of a surface active element such as sulphur. Estimates of the supersaturation ratio at which voids are produced in diffusion experiments yield a maximum of 1.01. Inasmuch as the foregoing mechanisms of void nucleation probably will not operate at this level—too low a surface energy is required—the investigatol. is led to the conclusion that voids must already exist. That is, nucleation of voids probably does not occur. Rather, existing submicroscopic voids grow out to visible size. Already existing voids might be produced during solidification or working. Supercritical sized parlicles which contain cracks may act as heterogeneous void nuclei. Gas pockets may act as void nuclei. Experiments are desired to determine the nature of the heterogeneous void nuclei which grow out to voids in both diffusion and creep experiments. Void Growth Void growth might occur in at least two possible ways, depending upon whether the already existing void nuclei are at grain boundaries or within the grains. In the case of a spherical void far from a crystal boundary, vacancies are generated during creep as a consequence of the migration of suitable dislocation jogs&apos; and are also annihilated at sinks. Under these conditions, a steady-state concentration of vacancies is built up in the crystal, defined by the condition that for any differential volume the rate of generation of vacancies in that volume equals the rate of annihilation of those vacancies." This equality would lead to the development of a gradient of vacancy concentration radially outward from the void surface up to a radius where the vacancy lifetime becomes equal for all directions of vacancy migration. The distance over which this vacancy concentration gradient extends equals about 2vD,T* where D, is the vacancy diffusivity and T:&apos; the vacancy lifetime in a crystal outside the gradient in a zone of constant vacancy concentration. The vacancies generated in the region over which the gradient exists will annihilate more often at the void than elsewhere. Approximately a little over one-half the vacancies generated in the gradient zone will annihilate at the void. Hence, the growth rate of the void is given by on where R is the radius of void in centimeters, is the atomic volume, and R is the rate of generation of vacancies, number per centimeter" per second. R D and T* may be estimated in terms of other physical parameters." In particular, R = n.j e/b [3] where n is the average number of vacancy produc-

Jan 1, 1957