Search Documents

By C. M. Dice

This paper is one of a series being published by the Bureau of Mines on milling methods and costs. It describes briefly the procedure followed in concentrating hübnerite or? at the Ima tungsten mine, Lemhi County, Idaho. In October 1911 the Ima mill was utilizing combined gravity-concentration, flotation, and magnetic-separation units for the recovery of a tungsten concentrate and a pyritic silver concentrate approximately 120 tons of ore averaging 0.5 percent W03 is treated daily. The concentrates produced average 66 to 67 percent WO3.

Jan 1, 1943

By Fred H. Lightner

The feasibility evaluation of the Borealis project of Houston International Minerals Corporation (HIMCO) was initiated in October of 1980. The operation of the Borealis Mine and heap leaching plant began in late 1981. In order to achieve the rapid development schedule several items were necessary: 1) Pre-planning of environmental requirements and early study of key issues. 2) Adoption of conservative design criteria. 3) Coordination and cooperation between HIMCO and regulatory agencies. 4) Adoption of specialized engineering and construction procedures. 5) Careful evaluation of owner project management philosophy.

Jan 1, 1982

By Albert L. Brautigam, Michael C. Leigh, August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 1992

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

C. M. Kay, Chairman L. W. Moore, Post Chairman C. W. Conn, Vice-Chairman R. W. Shearman, Secretary-Treasurer BLAST FURNACE, COKE OVEN, AND RAW MATERIALS COMMITTEE F. C. Anderko, Chairman James Chisholm, Past Chairman W. F. Huntley, Senior Vice-Chairman W. O. Bishop, Vice-Chairman R. W. Shearman, Treasurer D. C. Brown, Secretary IRON AND STEEL DIVISION Gerhard Derge, Chairman J. J. Golden, Past Chairman B. M. Larsen, Chairman-Elect R. W. Shearman, Secretary-Treasurer THE METALLURGICAL SOCIEN OF AIME J. S. Smart, Jr., President C. C. Long, Past President K. L. Fetters, Vice-President T. D. Jones, Treasurer R. W. Shearman, Secretary

Jan 1, 1961

By Louis J. Sousa

In November 1989, the U.S. Bureau of Mines sponsored a 2-day conference to stimulate thinking and discussion about changing materials technologies and implications for the Government's materials information programs. On the first day of the conference, speakers provided overviews of developments occurring in each of the major materials groups. Emerging technological developments, applications, economic and national defense significance, intermaterial competition, and potential market growth in advanced plastics, polymer composites, ceramics, metals, and electronic materials were described. In general, the speakers forecast advanced materials market growth rates in excess of overall gross national product (GNP) though high costs will tend to limit growth outside of aerospace, defense, electronics, medical equipment, and other typically high value-added businesses. On the second day, a wide range of speakers representing several facets of the materials community described how advances in materials technology are creating a need for new types of data, statistics, information, and analysis. Reflecting the speakers' broad range of organizational, professional, and personal perspectives, an array of information needs was identified. Most requirements, however, seemed to fall into one of five major categories: Federal materials research activities, material standards, market and economic information, health and safety, and public policy.

Jan 1, 1990

By Marie-Aline Van Ende, In-ho Jung

A thermodynamic database for the oxyfluoride system CaO-MgO-Al2O3-SiO2-Na2O-K2O-Li2OMnO- FeO-F has been developed based on the critical evaluation and optimization of all available experimental thermodynamic and phase diagram data. The developed database can be used for phase diagram and equilibrium solidification calculations for multicomponent systems and for understanding the solidification behavior of mold fluxes. Based on this thermodynamic database, a simple kinetic model was developed to simulate the interactions between the mold flux and molten steel using effective equilibrium reaction volumes combined with the thermodynamic database.

Jan 1, 2014

By Charles P. Lazzara

Concentration profiles of low-pressure, slightly lean CH4-02-Ar flames have been measured in situ for the following unstable species: oxygen atom, hydrogen atom, hydroxyl radical, methyl radical, and formyl radical. The observed maximum mole fractions were 2.0X10-2 for H, 1.1X10-2 for OH, and 0.8X10-2 for 0; the maxima occurred in the recombination zone. Methyl and formyl radicals have maximum mole fractions in the reaction zone of 2.2x10-3 and 6x10-5, respectively.

Jan 1, 1973

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By Ted C. Briggs

Twenty-two compressibility runs were made with helium over the temperature range -5° to 80° C and at pressures to 800 atmospheres. A Burnett apparatus was used. Data from the runs were fitted to a fourth degree polynomial equation of state in the pressure and a weighting factor of Pr-3/4 was used. All data for a particular isotherm were treated simultaneously. A temperature function was found to represent the parameters B and C. Compressibility factors determined by this investigation are believed to be accurate to better than 0.05 percent.

Jan 1, 1970

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946

By J. C. Monette

Stripping of gold and silver from carbon is effected by means of two main processes (AARL and ZADRA ). The main rate-enhancing parameter in the stripping of gold and silver is temperature. A secondary rate-enhancing parameter is ionic strength. (1) Stripping is usually conducted within a solution containing sodium cyanide (0.1 -0.5% ) and caustic ( 1 -3%). The development of a chemistry that increases the rate of gold and silver stripping from carbon in a manner proportional to its concentration is described. Its use in atmospheric and pressure strips is also outlined.

Jan 1, 1992

By R. Steven Maxwell, Ulrich Petersen

Most minerals have experienced a slow hut perceptible decline in their annual primary production growth over the past hundred years. This decline is due to a combination of factors: (1) increased recycling; (2) exhaustion of the more accessible or higher grade ores; (3) partial substitution; (4) the more efficient use of materials; (5) progressive saturation of markets as living standards rise. Therefore, future demand for new mineral resources will probably be lower than anticipated. As the world population stabilizes, this slowdown in production growth will become even more pronounced.

Jan 1, 1979

By W. J. Kroll

This report on the bibliography of zirconium has been confined to those publications and patents that appear to be useful in the commercial development of the metal, both the malleable and the nonmalleable. The methods of production have been stressed and special attention has been given to the alloys. Compounds of importance, like the oxide and chloride, for the manufacture of the metal or of the alloys have been considered. The use of the oxide in refractories anal in the glass and porcelain industries has been omitted. The present survey is critical; that is to say, an attempt has been made to evaluate the effectiveness of suggestions made in the literature. The exhaustive work of Marden and Richy, Bureau of Mines Bulletin 186, published in 1921, has been taken as a base to start from with the intention of bringing the subject up to date with material published in the last 24 years. During this time there was considerable 'advance in the preparation of the metal and Its alloys, and in the development of new uses. On the other hand, there was little progress in the methods of decomposing the ores, so that the chapter on this latter phase is necessarily short.

Jan 1, 1946

By Albert W. Deurbrouck

This report describes preparation characteristics of significant coalbeds in Tazewell County , Va . In 1961 Tazewell County produced 933,110 tons of clean coal from six coalbeds ; the Lower Banner , Raven , Jawbone , Upper Seaboard , and Pocahontas No. 3 and No. 5. Samples from all of these beds , except the Lower Banner , were included in this study plus a sample from the Pocahontas No. 4 bed . Of the samples collected , only one would require upgrading to be of metallurgical quality . The coals ranged in rank from high- volatile -A to low- volatile bituminous .

Jan 1, 1963

CHEMICAL PRECIPITATION U.S. 4,067,789 - Removal of soluble manganous ions from a zinc sulfate solution formed by leaching roasted zinc sulfide ore with spent electrolyte. An excess of ammonium persulfate or like oxidant is added to the leach solution to convert manganese to insoluble, filterable gamma-manganese dioxide, and the precipitate separated from the solution by filtration. L. Harris and A. K. Hanson, Jr., assigned to Newmont Exploration Ltd. Jan. 10, 1978. 11 pp. (204-119). Filed: 5-3-76 (682.442). (Drawing on page 67.)

Jan 1, 1979

By Eder Zegarra Salazar

El presente trabajo tiene como finalidad de ejecutar un proyecto Glory Hole San Gerardo, cuyo objetivo es desarrollar un RAMP UP de 300, 1,000, 1,500, 2,000, 3,000, 4,000, 5,000 TPD de mineral, como resultado de este proyecto de ampliación será necesario construir nuevas instalaciones de apoyo y de servicios a la mina, tales como talleres, almacenes, polvorín, ore passes, campamento etc. Estas deberán ubicarse en una zona que no afecte la futura expansión del proyecto con el método de explotación a tajo abierto.

Sep 1, 2017

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019

Mounting pressures to increase efficiency and yield, conserve energy, or minimize pollution have all taken their toll on the minerals industry. As management and technical personnel take a harder look at their operations for ways to shave cents off operating costs or to squeeze a bit more productivity out of existing equipment, instrumentation often comes up as the most effective answer. When Amax Lead installed an automatic grind control system in its Buick mill, ore throughput increased by 3 to 5%. Mill operators calculate that the initial investment is returned to them several times annually.

Jan 2, 1978

By William J. Bryson

Just picture, if you will, the hot, lonely and desolate Ochre Mountains west of Salt Lake City. There works a grizzled old miner, his boots worn down, his clothes hang on a body stooped by years of hard labor. His skin is wrinkled and leather toughened by many years in the hot desert sun. His ever faithful burro stands patiently in the shade of a large rock as the tired old miner examines ore samples just acquired that very morning. Suddenly the old man's eyes widen, his breathing becomes rapid. 'Leaping to his feet, with a gleam in his eye, he cries, "Eureka, I'm rich, I've found the mother lode. This is where I will start my digging. " Without warning, the silent wilderness is alive with wild, shouting, charging figures! Frightened the old miner glances about him wide-eyed and pan- icky. His heart sinks, dismayed he now knows all is lost, this is the end. For there leaping from behind rocks and brush papers in hand, are the men from the Department of Interior, Bureau of Land Management, State Mine Inspectors, OSHA, MESA, EPA, OEO, and the never ending list of regulatory bodies related to todays mining industry.

Jan 1, 1975