Search Documents

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck' reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.' The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.' A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

The curve of Fig. 3 for pyrite requires modification. There 11% a range of pH values from 6.2 to 7.8 for which no cyanide is required to prevent contact. From 7.8 to 11.3 a small amount of cyanide is required, with a sharp maximum of 20 mg. per liter at pH=9.6. The mistake arose from considering too few solution compositions (17 were considered) in constructing the curve. Subsequent work with other collectors indicates that the corrected curve is typical for such systems; it illustrates the further development of the dip in the pyrite curve of Fig. 5.

Jan 1, 1938

By C. Arthur Lefler

The Smoky Valley Mine is jointly owned by Louisiana Land and Exploration Company, Felmont Oil Corporation and Case Pomeroy Company. Copper Range Company, a subsidiary of L.L. & E. is the operator of the mine. The mine is located about 60 miles (100 km) north of Tonopah, Nevada on Highway 376 (formerly 8A) in the Big Smoky Valley on the western flank of the Toquima Mountain Range In the shadow of Mount Jefferson. The mine is at an elevation of about 6100 ft. (1860m) and is situated on the southwestern flank of Round Mountain, the hill for which the town of Round Mountain is named. The ore is a rhyolitic iglmbrite with coarse gold occurring along fractures and with fine microscopic gold disseminated in the rock mass. Minor silver is associated nth gold. Annual mining is planned at 5.8 million tons (5.3 million tonnes) per year with 2.2 million tons (2 million tonnes) as ore (7,000 tons or 6,400 tonnes per day).

Jan 1, 1981

By Ari Jokilaakso, Junjie Shi, Zhuo Chen, Pekka Taskinen, Xiang Gao

The amount of copper flash smelting slag has increased during the recent years along with an increasing slag-to-metal ratio. During slag tapping, some copper sulfide is mechanically entrained. As a result, it is necessary to recover copper matte from the slag by suitable methods. At present, the most common way is slow, controlled cooling in a transfer ladle. However, research on the detailed effects of slow cooling and the function of slag modification is rare. This paper described experiments that were performed at different cooling rates (0.5, 1.5, 3, and 7 °C/min), with and without additive. A detailed characterization of the copper-rich phase and its particle size was subsequentlymade using SEM-EDSmicrographs and image analysis software.With a decrease in cooling rate, the particle size of the copper-rich matte phase became larger. The addition of gypsum and carbon as a slag modifier affected the size of the copper-rich phase slightly, and its chemical composition was modified compared with the experiments without additive.

Jul 31, 2020

By C. S. Lord

"The Regal Silver mine is 5 miles north-northwest of Albert canyon; a station on the main line of the Canadian Pacific railway; 21 miles east of Revelstoke; British Columbia.Development, commenced in 1918, comprises more than 8,000 feet of workings from six adits, one of which extends into the Regal Silver property from the adjacent Snowflake ground. Production has been limited to a little tungsten concentrate recovered recently from a few r..undred tons of ore treated in a small underground mill. The property has received some attention as a possible source of tin. The deposits are large quartz veins containing irregular sulphide bodies. Ore minerals normally make up less than 1 per cent of the veins and include pyrite, galena, sphalerite, scheelite, and stannite. The veins are approximately parallel with the bedding of the enclosing graphitic, siliceous to calcareous, slates and argillites. These strata are of Precambrian age, strike about northwest, and dip northeast. No other rocks are known in the vicinity of the workings . Granitic rocks, intrusive into t'he sediments, outcrop 4 miles to the southwest and 7 miles to the northeast and may underlie the property at no great depth."

Jan 1, 1954

By Xie Junjie, Li Shina, Ma Ruixin, Min Changli, Yin Zichen, Li Kang, Shi Zhuonan

Cesium and rubidium were effectively separated by zinc ferrocyanide coprecipitation method, and the effect of precipitant addition amount on the separation of cesium and rubidium was studied. Under the conditions of Zn/Cs molar ratio of 0.45 and Zn/Fe molar ratio of 1, the precipitation rate of cesium is 84.01% and the separation factor of Cs/Rb is 164.65. The thermogravimetric curves of the sediment were measured, and the effects of roasting temperature, roasting time, and leaching liquid/ solid ratio on the extraction of cesium were studied. Almost all of the cesium was extracted under optimal conditions: roasting temperature of 600 °C, roasting time of 3 h, leaching temperature of 25 °C, leaching time of 0.5 h, and liquid/solid ratio of 5:1 mL/g. After the leaching process, the leach liquor with high concentration of cesium of 80.17 g/L was obtained. Finally, the leach liquor was further purified by solvent extraction, and the purity of the cesium chloride product reached 99.66%.

Mar 17, 2024

By Margaret Armstrong

The increasing cost of developing new mines and the need to mine more marginal deposits have led mining companies to use more sophisticated estimation methods such as kriging. But until recently, coal mining companies have shown little or no interest in these techniques. However, the stringent quality controls which are now placed on coal have led to a surge in interest in improved estimation methods. This can be seen from the -, number of research projects by private companies and governmental agencies on the application of geostatistics to coal reserve estimation. At present, most of these programs are centered on the problem of estimating the tonnage and the average grade (i.e. ash percent, sulphur content, calorific value, etc.) of the coal in-situ. See, for example, Sabourin (1975), Woods (1976, 1979), Pauncz and Nixon (1979) and Armstrong (1980). These studies show that the established techniques of linear geostatistics can be applied successfully to coal deposits. The study by Woods is particularly interesting because he had access to the actual production figures as well as the initial sample data from the no 2 seam in the Greenside Colliery owned by the Anglo-American Corporation. He showed that the estimates obtained by kriging were consistently closer to the actual production figures than those given by three other estimation methods. This confirms the superiority of kriging as a method of estimating block values for coal. Another advantage of geostatistics is that it can be used to determine the optimal spacing between drill holes. An example of this is given by Armstrong for the coking coal deposit in the Bowen Basin, Australia.

Jan 1, 1981

By Maynard H. Jameson

EARLIER investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.1 The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,2 and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. THEORY Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredge3 determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities po, pi, and p2 are involved, and the source I is located at the interface of the media (po) and (pi). The perpendicular depth of the lower interface is h,? is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: [ ] As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is ?, the angle measured from the horizontal to the first image is 2? to the second image it is 4?,, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1941

By W. H. HOWARD

Discussion of the paper of W. H. HOWARD, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 2029 to 2046. EDGAR M. DUNN, Anaconda, Mont.-Mr. Howard's contribution to the literature on the Cottrell, method. of electrostatic precipitation of flue dust and fume at Garfield has been read by us with peculiar interest for the reason that we have been experimenting with the same process at Anaconda for the past eight or nine months, with a view to adapting it, under the direction of Dr. Cottrell and the supervision of J. 0. Elton. and D. R. Kellogg, representing the Anaconda Smelter Commission, to the treatment of very large volumes of gases, using large pipe treaters and various forms of electrodes, with about 150,000 volts rectified current. For the amount of gas to be treated here the 5-in. pipe means a cost for installation that is practically prohibitive, clue to the tremendous number of pipes required, and we have been trying to cut installation costs by increasing the size of the pipes. All of our work is still in the experimental stage, but we have obtained good clearance on our mixed roaster and converter gases with a 3-ft. pipe treater 20 ft. long, and with 5 ft. velocity therein; and with a discharge electrode of a single No. 29 nichrome wire set in the middle of the 3-ft. pipe, with. a consequent electrode spacing of 18 in. The current used has been 150,000 to -160,000 volts, .and of course there have been troubles galore, relating particularly to insulation and rectifying. Blast-furnace gases did not give so good clearance, probably due to relative poverty in moisture and S03 content of blast gases to roaster-converter gases; making the blast gases the poorer in conductivity. Our experience has been so satisfactory that in our next experimental plant-built on a somewhat larger scale-we shall attempt a 4-ft. treater with greater electrode spacing, and a somewhat higher voltage-up to 220,000. As to fractional precipitation, mentioned by Mr. Howard, this idea was tried out at Anaconda last year (1913). Formerly our furnaces (Bruntons) roasting flue dust for the recovery of white arsenic, passed so great an, amount of dust to the settling kitchens that refining of this arsenical product was necessary to eliminate the 5 to 20 per cent. dust contained therein. Consequently the manufacture of As203 was effected in two stages, with a reverberatory roast of the first .product to obtain the final 99.5 per cent. As203. -

Jan 11, 1914

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By Frank E. Williams

This Bureau of Mines report deals with the urbanization of Tucson, Ariz., a southwestern city with an arid environment. Zoning regulations concerning known aggregate sources are described, and information relating to projected needs for the urban area is furnished. History of growth is outlined not only for the local aggregate industry, but also for the entire urban area. Past conditions are pointed out and background material for future conditions is provided.

Jan 1, 1967

By W. D. Judge, Z. W. Xiao, G. J. Kipouros

Rare earths have taken a prominent position in the Hi-Tech field after the discovery of the NdFeB permanent magnets. Their use in the magnets sparked miniaturization of the communication devices such as computers and mobile phones and are being considered in many more applications. Potential applications of rare earth elements in energy conversion technologies including wind turbines, photovoltaics, and other renewable energy systems are reviewed, along with sustainability considerations and production processes.

Mar 1, 2017

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By ERNEST F. . SURCEIARD

work have been published from time to time by the Survey.' A detailed report on the Birmingham district, with maps, has been completed, and will be published within the next year." In the following paper it is aimed to present only an outline of the geologic relations of the ores, since the Appalachian geology of Alabama has been discussed by many previous writers, but to describe rather fully the ore of the Birmingham district, and to discuss its relations and probable extent. IT. OUTLINE OF THE GEOLOGY. 1. Stratigraphy. The pre-Pennsylvanians rocks exposed in and along the borders of the valley-regions of Alabama, range from middle Cambrian to Mississippian (Lower Carboniferous), and at the SW. extremities of the valleys these rocks are overlain by coastal-plain deposits of Cretaceous and Tertiary age. A generalized section of the pre-Pennsylvanian Paleozoic rocks for the valley-regions is given in Table I. TABLE I.-Section of Pre-Pennsylvanian Paleozoic Rocks in Valley-Regions of Alabama. System. Formation and character. Thickness. Ft. Shale and sandstone 300 to 2,200 Carboniferous (Mississippian- Limestone and shale 300 to 800) I Sandstone and shale 50 to 200 1 Fort Payne chert and limestone 100 to 300 Devonian Chattanooga shale 0 to 30 Silurian Clinton (" Rockwood ") shale, sand¬ stone, and iron-ore 200 to 700 Ordovician Chickamauga ("Trenton") limestone.. 200 to 800 Cambro-Ordovician Knox dolomite and chert 1 2,200 to 2,700 basal dolomite 500 to 600 Cambrian Conasauga shale and limestone 1,000" to 1,500 - I a Base not. exposed.

Nov 1, 1908

By X. J. Lyu, Q. Liu, M. J. Lian, X. Q. Cao, X. F. You, B. O. Erdenekhuyag, H. Y. Zang

The slag-tailings based artificial reef concrete (ARC) is made of CaO-CaSO4 activated granulated blast furnace slag (GBFS) as cementitious material and deslimed gold ore tailings as aggregate. In order to investigate the potential application of the material as ARC, the strength development, hydration characteristics and application performance were investigated under different preparation conditions. Results indicated that using seawater as the mixing water can effectively promote the hydration of slag and generate a large amount of hydration products such as ettringite, CSH gel, hydrotalcite and Friedel ’s salt in the early curing period and so render the material with good early compressive strength. Seawater curing can also accelerate the hydration reaction in the early stage of hydration. The hydration reaction of slag and the compressive strength of ARC can be effectively promoted by increasing the specific surface area of slag. The 28-day compressive strength of the slag-tailings based ARC prepared with 30-50% CaO-CaSO4 activated slag and 50-70% tailings can reach to 19.88-42.87 MPa. Also, the material has a low surface pH value, good resistance to chloride ion penetration, and sulfate corrosion. Keywords: Artificial reef concrete, granulated blast furnace slag, deslimed gold ore tailings, compressive strength, hydration characteristics

Jan 1, 2020

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By Emil Gathmann

Discussion of the paper of EMIL GATHMANN, presented at the San Francisco meeting September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1485 to 1492 H. W. LASH, Cleveland, 0.-I have found in practical experience that it is not objectionable to have some blow-holes in ingots. They enlarge during solidification and have a tendency to cause the steel to rise. If they are of fairly small size they weld up quite readily, especially where they are some distance from the surface. In that way a pipe, which is much more detrimental than a few small blow-holes, is prevented. There is a very great difference in the formation of blow-holes in steel. You get one condition in soft steel and entirely another condition in rail carbon, or the still higher grades. The figures that are given in Mr. Gathmann's paper I imagine are taken from the higher carbons, as it is very seldom that piping occurs in soft steel. J. W. RICHARDS, South Bethlehem,, Pa.-This contribution is very welcome, and I understand that the process of Mr. Gathmann is in practical use and has proven successful. I believe the experience of steel makers is that an ingot which has a pipe is of more solid structure, and therefore takes a great deal more work in the rolls and in mechanical treatment, than an ingot which has some blow-holes. The density of the piped steel is undoubtedly increased. My opinion is that it is un-

Jan 12, 1915

By J. Chipman, H. A. Wriedt

DURING the past twenty years, a considerable background of knowledge has been built up on the chemical behavior of oxygen in liquid iron. Little is known regarding oxygen in liquid nickel or the effect of nickel as an alloying element on the behavior of oxygen in liquid steel. The solubility of oxygen in liquid iron was determined by Fetters and Chipman' and, more precisely, by Taylor and Chipman.' The Ni-NiO eutectic was placed by Merica and Waltenberg"' * at 1438°C and 0.24 pct 0, and this point has been confirmed by others." O It was reported by von Bohlen und Halbach and LeitgebelT that nickel and its oxide are miscible in all proportions at 1600°C, but this report is discredited by observations of others. The melting point of NiO according to von Wartenberg and ReuschV s 1990°C. Approximate values of oxygen solubility at several temperatures were reported by Hensel and Sc0tt.O The data of Krupowski and Balickil0 are inconsistent with those of Hensel and Scott and indicate a solubility less than half that found in the present study. For oxygen solubility in Fe-Ni alloys under pure iron oxide-nickel oxide slags, only the scattered data of von Bohlen und Halbach and LeitgebelT are avail- able. The careful work of Bardenheuer and Brauns" involved silica-saturated slags. The equilibrium between Fe-Ni alloys and iron oxide-nickel oxide slags was studied by zur Strassenu and by Jander and Senf,u but no oxygen analyses were reported. Oxygen in Pure Nickel Apparatus and Nlethod: Samples were taken with a "Taylor sampler" from a bath of molten electrolytic nickel held under an air atmosphere in a magnesia-lined 30 lb induction furnace. Saturation of the melt with oxygen was effected partly by the addition of chemically pure black nickel oxide and partly by the air atmosphere. Samples were taken only when there was a clearly visible oxide phase present. To avoid contamination of this oxide phase, the silica-sheathed Pt—Pt-10 pct Rh thermocouples, by means of which temperatures were measured, were immersed in the melt for the minimum time consistent with accurate reading. Samples and temperature readings were taken only after the furnace had been

Jan 1, 1956