Search Documents

By C. R. Forbes, J. C. Barton

Many different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. Description" of Bits Tested 'I'he 4-point bits were the usual shaped bits commonly made on the Leyner sharpener, with 14' taper on the wings and a 90" angle between cutting edges. Some tests were run at 85 Ib. pressure with a 4-point bit made with a 50 taper on the wings; this bit was formed with the Carr bit dies. The 6-point bits were the usual shaped bits made on the Leyner sharpener. The Carr bits were made with a 5º taper and an angle of 100" between cutting edges.

Jan 1, 1918

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By Jean Bonnemaison

Societe Miniere & Metallurgique de Penarroya Noyelles-Godault works are located in the northern part of France. The complex includes a lead smelter, a zinc smelter, shops for production of manufactured products and all necessary general services. The zinc smelting complex described in this paper was designed in 1959 to replace an old horizontal retort distillation furnace and was first operated in May 1962. It includes: - a sinter plant producing the zinc sinter for the Imperial Smelting furnace : zinc, lead and bulk zinc-lead concentrates are sintered on a Dwight-Lloyd machine with a working area of 80 sq.m. Cadmium sludges are treated by the wet method in a separate plant for recovery of cadmium. Sulphur dioxide contained in gases goes to a gas washing tower and is subsequently made into sulphuric acid in a plant with a capacity of 550 m.t. per day. - a smelting plant where the process developed by Imperial Smelting Processes Ltd. is applied : the blast furnace which was modified in 1967 has an area of 17.5 sq.m. at the tuyeres level and a section of 24 sq.m. at the top of the shaft. It has a theoretical zinc capacity of 100,000 m.t. per annum. Air blast is heated by means of covers up to the theoretical temperature of 950ºC. Zinc produced is either directly cast into slabs for sale as standard 'good ordinary brand' zinc, or sent to a refining plant where the New Jersey process designed to produce 'special high grade' zinc is in application. Mixes of zinc containing various amounts of lead, cadmium or aluminum are prepared to customer specification in a mixing plant.

Jan 1, 1970

By J. F. Wolff

DURING the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision was done in only a few instances. The demand for refinements of work in this direction has caused caused extensive structural subdivision and correlation to he done in all exploration work during the past 4 years by the engineers of the Oliver Iron Mining Co. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Range, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7, 1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principle feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will he as follows: I. General geology. II. Subdivision of Biwabik iron-formation. III. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgment is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron. Mining Co., for permission to use the information presented in this paper.

Jan 10, 1916

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By Armando Vazquez

This paper will provide an overall technology update on Tenova’s modular i BOF® technology package for improved endpoint detection (Carbon and Temperature), slop detection and auto-tapping control, with a primary focus will be on Tenova's Slop Detection System (SDS). Accurate Slopping prediction is a critical tool in the operation of a BOF. It provides the steelmaker with an additional protective system to increase yield & productivity while reducing operating costs. Tenova Goodfellow's i BOF® slop-detection technology uses lance vibration analysis with real-time alerts to give steel makers advance warning of the onset of a slop and a measurement of the slop severity. The system is designed to provide direct feedback control of lance position and oxygen flow rate, for rapid mitigation of potential slopping events. This paper will provide a summary on how the i BOF® technology package has been implemented, including trials and general results.

Jul 30, 2018

By P. H. Royster

SOMETHING of a mystery has attached itself to the production of ferromanganese in the blast furnace. This alloy has been produced on the Continent almost continuously since 1876 and in very considerable tonnages, but little definite information concerning the practice is to he found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country prior to 1904, bit one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public. In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many, as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations. Realizing the advantages both to the country and to the industry from a pooling of operating data and experiences, the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Although the results of this investigation have already been reported to the companies cooperating, they may he of permanent metallurgical interest, so this paper attempts to give, briefly, the more important points brought out in the investigations. OPERATING DATA IN FERROMANGANESE PRACTICE Operating data were collected by the Bureau from 11 ferromanganese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P. The dimensions, of seven of the furnaces are given in Table 1. The companies from whom this infor-

Jan 2, 1919

By Klaus M. Hahn, Kurt Aasly, Jutta Lennartz, Hermann Wotruba, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Seafloor massive sulphide (SMS) deposits have been identified as important marine metal resources for the future. However, literature on mineral processing of SMS is currently limited, and to date, no research has been published on processing of SMS from either active or inactive hydrothermal vent fields on the Arctic Mid-Ocean Ridge. In this paper, individual SMS rock samples from the Loki’s Castle area were tested. Chalcopyrite, isocubanite and sphalerite represented the main copper and zinc bearing minerals in the SMS samples, whereas the gangue consisted of barite and silica. Based on the X-ray transmission response (XRT), i.e. differences in the atomic number of elements in tested samples, and using portable XRF (PXRF) values of elemental composition, individual particles were classified as a either product (low barium / high to low silicon / high copper and zinc) or waste (high barium / high silicon / low copper and zinc). The classification was based on the elemental composition of the samples with the cut-off grade equal to 0.5% for copper. It was shown that the XRT discrimination analysis correlated well with elemental (PXRF) data classification. The results clearly indicate that X-ray transmission sensor-based sorting can be used a useful technique for preconcentration of SMS rock samples. INTRODUCTION Due to different compositions of investigated samples, sensor-based sorting is a useful technique for preconcentration of different materials. The aim of using sensor-based sorting is to upgrade an ore by reducing the quantity of overall waste material reporting to the next processing stage. This can be achieved by eliminating (reducing) the waste fraction. By applying sensor-based sorting, the energy consumption for particle comminution as well as the required process water and reagents can be decreased. The total volume of the waste rejection leads to a proportional reduction in the total energy costs (Lessard et al., 2014, 2016)."

Jan 1, 2018

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for O2, N2, H2, He, and Co2. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4/CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By Junji Shibata

Through-hole copper plating is performed to make a multi-layer printed circuit board. The through hole plating is first carried out by Pd catalyst treatment, followed by copper non-electric plating. The amount of Pd catalyst used in one plant is about 0.25-2 m3/month (8 g/dm3 PdCl2 base) depending on the plant scale, and the cost of the catalyst reaches 17,000¬I35,000 US$/month. In this study, the flow and material balance of a Pd in Pd catalyst treatment process was investigated. About 60% of Pd catalyst adheres on the through-hole and other part of setup, while 25% is released into the washing liquor. Pd in the washing liquor should be collected by a suitable method like a pressure filtration using diatomite. The material balance of Pd in Pd catalyst treatment process and the recovery method of Pd from waste solution containing Pd catalyst was investigated.

Jan 1, 2003

By Frederic P. Dewey

This old and well-known method of determining silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, and because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a detemination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained. For this determination 1,115 mg. of standard metal are weighed and transferred to a glass-stoppered bottle, the metal is dissolved in nitric acid, and 100 cc. of a standard solution of NaCl run in. The bottle is then vigorously shaken and a measured portion of a decimal salt solution added, and again shaken, if necessary. These operations are repeated until the silver is precipitated. Standard metal being 900 fine, 1,115 mg. should carry 1,003.5 mg. of silver, which is a convenient figure to work with.

Jan 1, 1914

By J. E. Armstrong

"IntroductionT'HE PRODUCTION of gravel and sand may be considered to be the major mining operation in the Lower Fraser Valley of British Columbia. At least thirty pits are in operation with a yearly production probably in excess of two million yards and a value in excess of one million five hundred thousand dollars before crushing, washing, and sizing. The value of the finished products would probably be double the above figure.Since 1949, the writer and his co-workers have been engaged in the geological investigation of the Lower Fraser valley and adjoining Coast mountains for the Geological Survey of Canada. The study, which is not yet completed, includes both bed-rock geology and geology of the unconsolidated sediments lying above bed-rock. In a rapidly expanding industrial area, .an advance knowledge of the geology may• greatly aid in future 'planning, and in many cases may .prevent not only the wastage of large sums of money, 'but possible disaster. Some of the present and future applications in which geological information in the Lower Fraser valley should be of value are as follows: the development of domestic, irrigation, industrial, and municipal groundwater supplies; drainage for industrial sites,, roadbeds, and farmlands; flood control along the Fraser river and smaller streams in the area; the location of dam sites, of major tunnels for water supply •and sewage, of road-beds, of foundation sites for large buildings .and other engineering undertakings in which geology may aid; the evaluation of oil and gas •possibilities; the production of building stone; and the production of sand and gravel, the subject with which this paper is primarily concerned."

Jan 1, 1953

By Roy E. Peterson

The Bureau of Mines has been developing and evaluating methods for beneficiating the large deposits of nonmagnetic (oxidized) taconite located on the western Mesabi Range. In this segment of the research, a sample representing about 0.5 billion tons of nonmagnetic taconite from near Grand Rapids, Minn., was beneficiated using a reduction roasting, magnetic separation, flotation process. The sample contained 32.1 pct iron and 49.1 pct silica. Tests were conducted both on a bench scale and with a 1,000-lb/h pilot plant. In the bench-scale research a con-centrate containing 69.0 pct iron and 4.5 pct silica was produced with an iron recovery of 82.1 pct. In the pilot plant, reduction roasting was conducted in a 35-ft kiln using lignite as the reductant and major source of fuel. Dust from the kiln exhaust was pelletized and recycled to the kiln. The roasted taconite was beneficiated by magnetic sep-aration and flotation to produce a product containing 67.9 pct iron, 5.5 pct silica, and 69.7 pct of the iron in the kiln feed. The cyclone separation in the grinding circuit was sharpened by demagnetizing the cyclone feed in a 400-Hz, 1,000-Oe magnetic field.

Jan 1, 1983

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By John Birkinbine

EXTENDED discussions, by inviting attention to problems affecting the conservation of natural resources, have encouraged investigations as to their sufficiency, with the general result that the more thorough the examination, the less cause appears for anxiety as to the exhaustion or serious depletion of these resources. The extent of industrial development, the large plants and the enormous volumes of materials required, when compared with conditions a few decades ago, are sufficiently startling to enlist the attention of those who "fear .the pace," and yet in but few instances has real solicitude for the future. been warranted by a knowledge of true conditions. In a former communication, presented 5 years ago,1 I endeavored to emphasize the fact that true conservation represented the best utilization of reserves and not the locking up of resources for future use; a conviction which has become more pronounced as the subject was investigated. Prophecies of the, early exhaustion of mineral resources have raised the question as to our permanent reliance upon these, and encouraged inquiries which have in most cases developed reassuring conditions. But the fact that the future appears less dark than prognosticated cannot excuse wastefulness or improvidence; and detailed study which demonstrates an apparent abundance of natural resources should encourage their best application. In making inventories of resources one is liable to confine conclusions as to availability upon present circumstances and conditions in the past, or to formulate data for the future upon methods which are rapidly being displaced. In reserves which are not reproductive, such as minerals, the possibilities of exhausting the supply are startling if estimates assume that future extensions will follow methods which were less economical than those now employed, or to he used, and we dare not claim that the limit of advanced practice has been attained.

Jan 9, 1914

By Eric R. Jette, Earl S. Greiner

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968