Search Documents

By Robert Hopler

It is the nature of the initial detonation to the powder around the cap which governs the greater or less effect of the explosion of the whole charge. The cap communicates to the first particles of powder a disruptive impulse, which, according to the nature and strength of the cap, more or less completely overthrows their equilibrium and decomposes the powder with great energy, setting up sympathetic vibrations that explode the particles of powder in turn by the violent disturbances or friction between them in a regular succession of impulses and decompositions, which, if started with sufficient energy, are of such intense heat and velocity that the rupturing force of the explosive is developed practically instantaneously. This detonation has already been shown to be not only the result of mechanical force, but a combination of extremely sudden chemical and dynamical reactions which set up vibrations to which different powders are more or less susceptible, and these explosive reactions will be propagated through the mass of the powder according to the intensity of the vibrations and the resistance with which their motion is opposed by the nature and consistency of the powder, whether it be difficult or easy to oxidize, soft and plastic like dynamite, or hard. If the initial detonation of the powder surrounding the cap is of the highest degree, the vibrations will be most intense and will be propagated further through the mass than by a poorer detonation. Hence the different degrees of detonation. Unless the first particles of powder are so thoroughly decomposed by a detonation of high order, or first degree, as to convey the necessary heat and energy to detonate the whole charge, the greatest force of the powder will not be developed. There will frequently be unbottomed holes or pieces of unexploded powder scattered about, or both, and the air in the mine will be contaminated with some obnoxious gases that have not been completely oxidized.

Jan 1, 2007

By André van Wageningen

Since the beginning of this century Boliden Mineral and Atlas Copco have worked together in stages on improving the accuracy and quality of drilling. Navigation of the drill rigs with IREDES has been in use in the Boliden mines for several years. Recently the capability of the system has extended with map navigation to more accurately follow the ore in cut&fill mines. The system allows for changes on the individual round level to follow the ore without changing the whole design for the heading. Those changes are done in a CAD-system and remove the need for face markings and will allow for even better accuracy in both height and wall position. All the information between the CAD-system and the drill rigs is exchanged using the IREDES standard. This paper describes the workflow and the use of the IREDES standard.

Oct 1, 2009

By R. M. G. Machunter

Computer models of metallurgical circuits are extensively utilised in design, and prediction of overall plant separation performance. As always, in the final optimised flowsheet design there is a compromise between the recovery of values and grade of the circuit output. This paper mathematically examines various circuit options for the generation of a heavy mineral concentrate from a generic mineral sands wet concentrator plant. Based on data derived from testwork, any particular mineral sand has a unique release curve describing the separation performance of the heavy mineral suite. Models are constructed that combine particular stage output streams as feed to other stages in various configurations. The ramifications of each option are discussed and reasons why one particular option is selected over the others examined.

Jan 1, 2005

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961

By Z. Hyder

Simulation and modeling is powerful tool to analyze real time data and can be used to analyze different scenarios using appropriate software that may reduce need of infield data collection process and can predict reasonably accurate results. In this paper the real time data of a mine is used to simulate and model the stresses on the pillars and evaluate the pillar strength and safety factor. The material properties assigned to the model are obtained by testing the representative samples taken from the selected locations of the mine. The mine under investigation has 50 ft wide pillars and 50 ft wide rooms under an average overburden of 650 feet. The effect of reduced pillar dimensions and increased roof span on overall stability of mine and extraction ratio is analyzed using LaModel [1] software. The predicted results of the reducing pillar size are analyzed to compares the current mining practices with the optimized room and pillar size to get better extraction ratio without comprising the safety.

Jan 1, 2011

By Roberto Golchi

This article describes the method used to quantify the Environmental Impact for the mining, by drilling and blasting, of a borrow pit for a gravity-dam. The affected environment was broken down into a number of components, such as public health and safety, social relationship, air and water quality, flora and fauna. The effect of the various impacting factors from the mining activities, both directly and indirectly, was then calculated for each environmental component. To do this, each impacting factor was first given a magnitude, a number based solely on the range of scenarios possible for the impacting factor. A matrix of weighting factors was then derived to systematically quantify, and normalise, the effects of each impacting factor on each environmental component. The overall impact upon each individual environmental component was then calculated by summing the weighted magnitudes for all the impacting factors.

Jan 1, 2003

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By V. Velicka, J. Ptacek, R. Snuparek, P. Konecny, G. Takla

Coal mining in Ostrava-Karvina coalfield is being accompanied by rockbursts. 82 rockbursts occurred within the period between 1990 and 2002. Natural and technological factors from these rockbursts were collected and analysed. They confirmed that rockbursts are complex geomechanical events and that the relations between co-acting technological and natural factors are very complicated. Der Abbau in dem Ostrava-Karvina Steinkohlenrevier wurde von Anfang an durch Gebirgsschläge begleitet. 82 Gebirgsschläge in dem Zeitabshnitt von 1990 bis 2002 erfolgten. Die Angaben über natürliche und technische Faktoren der Gebirgsschläge wurden gesammelt und analysiert. Es wurde bestätigt, dass die Gebirgsschläge komplexe geomechanische Phänomene sind und dass die Beziehungen zwischen den zusammenwirkenden Faktoren sehr kompliziert sind. L´abattage d´houille dans le Bassin houiller d´Ostrava-Karvina est accompagnée par les coups de terrains. 82 coups de terrains s´étaient produit dans la période entre 1990-2002. Les données sur les facteurs naturels et techniques ont été ramassées et analysées. Les résultats ont corroboré que les coups de terrains sont des phénomènes géoméchaniques complexes. Les relations entre les facteurs techniques et naturels coopérants sont très compliqués.

Jan 1, 2003

By ATF Publications

The following is a summary of the changes that were incorporated into the new Federal Explosives Regulations, 27 CFR Part 55, dated 9/2000. However, in light of the recent events of September 2001, additional changes in the Federal Explosives Laws and Regulations may be forthcoming. The nature and extent of any such potential changes are impossible to gauge at this time. However, this synopsis of the changes contained in the September 2000 Orange Book, ATF P 5400.7 was current at the time of this writing. Any questions regarding this paper should be directed to the Public Safety Branch in ATF Headquarters in Washington, D.C.

Jan 1, 2002

By H. Wagner

During the last few years a large number of pillars in different mines were investigated. Pillar conditions were evaluated using subjective, empirical, geophysical and numerical methods. A critical comparison of the different methods showed some interesting coherence. This paper concentrates on experiences using the p-wave velocities as an indicator of pillar conditions. Während den letzten Jahren wurde eine große Anzahl von Bergfesten in verschiedenen Bergwerken auf ihren Zustand hin untersucht. Hierzu wurden subjektive, empirische, geophysikalische sowie numerische Methoden angewandt. Dieser Vortrag beschäftigt sich mit den Erfahrungen beim Einsatz der p-Wellengeschwindigkeit zur Beschreibung des Festenzustandes. Le condition géotechnique d’une grand nombre des piliers des mines souterraines différentes sont examinées ces dernières années. On a appliqué des méthodes subjectives, empiriques, géophysiques et numériques. Ce rapport occupe aux expériences avec l’application de la vélocité des ondes de compression pour tracer le condition des piliers.

Jan 1, 2003

By Jack T. Work

Spiraling costs in every segment of the open-pit mining cycle is a fact of life that every operator must reckon with. The introduction of various shock absorbing devices for rotary drilling is one recent innovation that may significantly reduce overall drilling cost, increase drill availability, and lower maintenance requirements. In a recent all-inclusive test in taconite ores, shock absorbers on Bucyrus-Erie BE 60R and Gardner¬Denver GD 120 rotary drills were directly responsible for overall savings of up to $41.06 per hour. What is It? A shock absorber is simply a device installed between the rotary drive head and drill steel that cushions the two. It functions in the same manner as springs and shocks on an automobile. Some benefits associated with use of the tool are readily apparent on a daily basis; other benefits are realized over longer time intervals and through continued use. A properly designed shock absorber will: •protect the drill from severe vi¬brations, improve rock bit performance, allow application of the best weight-on-bit and rotating speed under all drilling conditions, •function effectively over a wide range of applied bit weights, • have a spring rate soft enough to perform its primary function of absorbing both rotary and vertical vibrational forces generated by rough drilling, •be reliable and subject to as little maintenance as possible, •be easy to install and remove, and • be of such an economic benefit so as to offset the added expense of its application. A shock absorbing tool developed by BJ-Hughes Inc. was used in a recent test. The "Smoothdrill" is just one of the products currently available. This unit absorbs both rotary and vertical shock loads and has no mechanical parts so lubrication is unnecessary. A rebuild of the unit consists of removing the worn rubber element and inserting a new element, an operation taking less than one hour. Minimizing Vibrations Severe vibrations on a blasthole drill operating in broken and discontinuous formations have visible effects. These vibrations often cause structural damage when allowed to&apos; continue, resulting in fatigue cracks in the mast and related structural components in the drill. When rough running formations are encountered, drilling must be interrupted and possibly shut down. Usually, the drill operator resumes drilling using less down pressures and various rotational speeds until firmer drilling is encountered. An effective shock absorber can substantially reduce these vibrational forces so more down pressure can be applied in bad ground. It is generally accepted that longitudinal vibrations and cyclic forces are more effectively reduced if a tool is designed to incorporate a relatively "soft" shock absorber. The softness of any shock absorbing tool is best judged by its spring rate-the weight required to produce a given amount of deflection, commonly expressed in units of kg per mm or pounds per inch of deflection. All shock tools use a resilient member such as rubber springs, steel springs, fluid, or gas springs to absorb

Jan 4, 1980

By Michael F. Barber

"Highway slopes are intended to remain stable over a long period of time. Unexpected slope failures can be costly in terms of human life and property damage or loss. Cleanup of failures can prove to beextremely expensive."

Jan 1, 1999

By H. E. Brauer

PART I INTRODUCTION Among the zinc base alloys used for casting in metal moulds, particularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortness which facilitate casting. Objection to the use of these alloys may bee raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intercrystalline corrosion. In all cases which have come to our knowledge where the conditions of service were known, failure has occurred upon exposure to moisture and heat varying from a hot moist atmosphere to high pressure steam. Moreover, the alloys described in all such cases contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intercrystalline oxidation in zinc-aluminum alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Bauer2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the most part, and Rawdon&apos;s3 examinations were made on an alloy containing 0.4 per cent. lead also exposed to the Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to determine the exact nature of this phenomenon and the effect of other metals present as impurities or intentional additions in accelerating or-retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation.

Jan 8, 1922

By Liu Yulin, Zhao Yi, Tan Qi, Liu Lei

"Hydrotalcite is one kind of layered double hydroxides, and has special crystal chemical characteristics. Due to its good thermal stability, hydrotalcite used as the PVC heat stablier has attracted scientists’ attention. In this study, nano-hydrotalcite was synthesized by the method of mechanochemistry/crystallization, using brucite, Al(OH)3 and Na2CO3 as raw materials, and added into PVC to investigate the effect of hydrotalcite on thermal stability of composites. The synthesis mechanism was suggested by virtue of XRD, FE-SEM, FT-IR. It has been indicated that at the first of dry milling process, the parical sizes of brucite and Al(OH)3 decrease, while specific surface areas of them increase by the action of mechanical force, until produced amorphous particles. In the process of wet milling, metal ions in the amorphous body, which has high surface energy, can easily react with H2O, and produce the precursor of Mg6Al2(OH)18•4.5H2O, which has the same crystal structure as hydrotalcite. Under the hydrothermal condition, anions of OH- in the interlamination of precursor are exchanged by CO32- in the solution and nano-hydrotalcite is generated at last. The thermal stability was characterized by Congo red method. The results have revealed that hydrotalcite is one kind of long-term heat stabilizer, and residual stability time increase with the rise of added hydrotalcite amounts.INTRODUCTIONHydrotalcite, one kind of anionic clays, has been attracted a great interest for researchers because of their unexpected physical and chemical properties. The general formula is Mg6Al2(OH)16CO3·4H2O, where Mg2+ and Al3+ occupy octahedral positions in the brucite-like layers, and CO32- is an interlayer anion (Hoyo, 2007). Hydrotalcite is widely used in the fields of chemical engineering, materials engineering, environmental protection, medicine, and so forth, owing to its unique capability of adsorbability, ion exchange and thermal stability (Rozov, Berner, & Taviot-Gueho, 2010; Iwasaki, Yoshii, & Nakamura, 2012; Ay, Zümreoglu-Karan, & Temel, 2011; Cavani, Trifiro, & Vaccari, 1991; Li & Duan, 2005; Lin, Wang, & Evans, 2006). As a result, the study on synthesis and application of hydrotalcite has received considerable attentions."

Jan 1, 2016

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente&apos;s output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By Noan Tonini SImonassi

A utilização de compósitos de matriz polimérica reforçados com fibras naturais vem assumindo um papel importante no âmbito da engenharia de materiais. O baixo custo, a biodegradabilidade e a redução do peso especifico torna a utilização desse tipo de compósito bastante atrativa. O objetivo deste trabalho é avaliar o desempenho da fibra de sisal como reforço do policarbonato visando uso utilização militar, especialmente em proteção balística. Antes da confecção dos corpos de prova, foi realizada a redução no tamanho de partícula do policarbonato e da fibra de sisal através de um moinho de facas, posteriormente dos corpos foram submetidos aos ensaios de tração e flexão.

Oct 30, 2017

By R. H. Doremus, E. F. Koch

The first carbide phase that precipitates at 120°C from a iron containing about 0.02 wt pct, C was studied with the electron microscope. In both strained and unstrained material the carbide particles appeared to form on the dislocations in the iron, in agreement with the results of the kinetic study in part II. The structure of the carbide was tentatively identified as an expanded a-iron lattice (body-centered tetragonal) with about 0.7 wt pct C. This phase appeared to be metastable and apparently transformed into cementite or epsilon carbide when the iron was over-aged. WhEN a iron containing less than about 0.025 wt pct C is quenched from 700°C to room temperature the carbon is retained in solid solution and precipitates out slowly with time. The morphology and structure of the precipitating phase are still in doubt, two different carbide phases, epsilon carbide and cementite, have been identified, but there is considerable disagreement about the time and temperature at which they appear.1-4 Epsilon carbide seems to form at lower temperatures than cementite, although one group of investigators4 found only the latter phase over a wide range of aging temperatures. Usually these two phases have been identified after aging times much longer than needed to drain the carbon from supersaturated solution, at least for aging temperatures below 200oC. The precipitated carbides have been observed with the electron microscope,&apos;-5 but again most results have come from samples aged much longer than necessary to reduce the carbon concentration in solution to a low value. In this study the carbide phases were observed in earlier stages of precipitation with the electron microscope, in order to learn more about the shape, size, and distribution of the carbide particles. Samples strained small amounts before aging, as well as unstrained samples, were studied, and the structure of the carbide phase was tentatively identified. EXPERIMENTAL "Ferrovac E" vacuum-melted iron, from which the wires for kinetic studies were also made (Refs. 6 and 7 and the following paper) was used for this work. An analysis of this material is given in Table I; it agrees well with the manufacturer&apos;s values. The number of inclusions in the iron was very small, as can be seen in the optical micrograph in the following paper. Pieces of iron about 1 mm thick and 5 to 10 mm in diam were used for all the studies except for those in which the sample was strained before aging; then the specimen was a rod 3 to 6 mm in diam and 20 cm long. The samples were held at about 700°C in wet hydrogen for at least an hour to remove residual carbon and nitrogen, after which they were heated to 950" (in the y region) and cooled to room temperature in the furnace. This treatment gave an average grain diam of more than 1 mm, so that the effect of grain boundaries on the precipitation process was negligible. The samples were carburized at 710°C for about 2 hr in hydrogen that had passed over toluene held at -30°C; then they were rapidly quenched into water. From chemical analysis this treatment gave a carbon concentration of from 0.012 to 0.016 wt pct, which is less than the solubility of carbon at this temperature. After quenching, the samples were aged at 120 "C in an oil bath for vari-

Jan 1, 1961

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990