Search Documents

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the 'fine' and 'coarse' size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: > Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery > Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery > Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for fine, and 'coarse' particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2013

By Gary Eck, Kevin Tallent

Over the past decades, the science of energetic materials has advanced dramatically in both the fields of military munitions, as well as industrial explosives. Out of necessity, test methods to measure the explosive performance properties of these materials were developed. As would be expected, these test methods have evolved and become more sophisticated with the recent advancements in electronics and computerized technologies.

Jan 1, 1998

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

By John C. Calhoun, Frank T. Bethel

The application of a method for analyzing pressure build-up curves to determine the effective permeability in the Spraberry is presented. Sixteen upper Spraberry wells of the Driver area arc analyzed and show variations in the in-place effective permeability of 2 to 183 md. Since these value- are much larger than the .5 md. or less reported for the matrix rock. a large part of the vertical fractures noted in Spraberry cores- must be considered native to the formation. The effectiveness of the well fracture treatment in connecting the well bore to the native fracture system is analyzed by comparison of the effective permeability as determined from the PI test to that obtained from a pressure build-up curve. These results show that the fracture treatment is sufficiently effective in connecting tile well bore to the native fractrure system to yield a flow capacity within about 50 per cent of that dictated by the native fracture system About two-thirds of the wells show some degree of local blockage. INTRODUCTION Fractured reservoirs have been known in the past.' However, during the past two years the Spraberry formation has directed the attention of the petroleum industry to a study of the performance of a fractured reservoir. The large variation in the number of fractures noted in Spraberry cores rile large variation in the producing ability of offset well.. the dramatic effect of well treatment on well ,productivity. the unknown quantity of oil stored in the fractures and matrix rock. and the unknown oil to be recovered were part of the initial Spraberry puzzle. In this type reservoir where the well treatment is an important factor in determining the productivity. it i- particularly desirable to determine the in-place flow capacity of the drainage area at distance* far removed from the well bore. This value. when compared to the flow capacity obtained from a PI measurement, will show the effectiveness of the well treatment (completion. fracture treatment, acidization. etc. in establishing a flow capacity in the vicinity of the well bore equal to that in the more remote region. The object of this paper i.; to show the application of a method of pressure build-up analysis for this purpose in studying the Upper Spraberry formation in the Driver area. STATEMENT OF THEORY The theoretical basis for the application of a pressure buildup curve to show the effective permeability of the rock at distances far removed from the well bore has been presented in detail in earlier publications.', in the previous development it was shown that pressure build-up behavior of all wells could be reduced to the same dimensionless build-up curve of Fig. 1. This mean.; that the bottom hole pressure of a well after hut-in will rise in such a manner that a plot of pressure against the logaritllm of time yields a straight line. The slope of this linp can be rlzed to calculate the effective permeability as expressed by the following equation: where: effective oil permeability md oil production rate prior to shnt in. STB/I) In practice the flow which occurs into the well bore after shut in and the variation in flow capacity in the immediate vicinity of the well bore usually cause the early part of the build-up curve to be unsatisfactory in the determination of permeability. In general the effect of these factors on the straight line section will become negligible after a time when the of the following equation is equal to 0.1. and the preferred section Of the curve for use in defining the slope lie-

Jan 1, 1953

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By K. Wenrich

The uranium industry has made a dramatic turnaround in the past three years that even the most optimistic economist was not willing to predict during the uranium downswing of the 1990s. Uranium reached a 30-year low in February 2001 of $6.50/lb. By the end of February 2006 it had soared to $38.50/pound. This nearly 600% increase in the uranium spot price within 4 years dwarfed the increase in gold price that has barely mustered a 100% increase. The initial slow rise from $6.50 in February 2001 to $10.75 in April 2003 (fig. 1) was primarily driven by the decrease in the value of the dollar. Since then several factors have contributed to the soaring price: (1) The awakening of many to the simple fact that uranium supply has not met demand for several years and that the world’s stockpiles are being drawn down, (2) How sharply this fragile supply can be impacted by disasters at the world’s major uranium production facilities, such as a) the flooding of the McArthur River Mine in the spring of 2003, b) fires at Olympic Dam, c) the potential that Rossing, with an annual capacity of 4000 tonnes uranium might close by 2007, (3) the withdrawal of Tenex from the HEU (highly enriched uranium) feed agreement, and (4) the announcement by the Chinese of their intent to build 30 new nuclear reactors.

Jan 1, 2007

By R. P. H. Willis

Uranium is back on the radar. Uranium has always been a controversial metal, from its role in the arms race to its claim to be the only viable alternative to fossil fuel. This paper will cover its properties and use, its occurrence and production in South Africa, the current market drivers and its future role as a primary energy fuel. It will highlight the difference between uranium used to make a bomb and uranium used in a power station. The recent significant uranium price rise will be put into context of the market drivers including geopolitical issues. Planned expansions in nuclear power station capacity will be reviewed, as will new mine production. Future demand will also be speculated on.

Jan 1, 2006

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By Thomas M. Keevin, Gregory L. Hempen

"Natural resource agencies, under various regulatory authorities, are challenged with permitting underwater explosive use while at the same time protecting aquatic resources. Deciding on whether or not to allow use of explosives requires striking a balance between development and aquatic resource protection. A company’s goal in underwater explosive use is to select methods that are both expedient and cost effective. The use of explosives is often the best alternative for engineering reasons or economic considerations. Over and above legal requirements, indiscriminate destructionof fish and other aquatic resources is not in a company’s best interests because of concerns relatingto public image, as well as the need to secure future contracts."

Jan 1, 1995

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971

By H. Hurkchand

Background: A cross-sectional study was conducted in November2001 to establish the prevalence rates of Human Immunodeficiency Virus (HIV) and sexually transmitted infections (STIs) (Chlamydia trachomatis and Neisseria gonorrhoea) in a coalmining town in Mpumalanga. Methods: 155 adults were recruited (79 males and 76 females), by holding community meetings, and by door-to-door recruitment. Saliva and urine specimens were collected for the analysis of HIV and STI prevalence, respectively. Results: The mean age for males was 31.35 years (min = 19 yrs and max = 50 yrs) and the mean age of the female participants was31.90 years (min = 17 yrs, max = 49 yrs). The prevalence of HIV was found to be 22.78% [95% CI (14.09?33.59)] in the males vs. 47.37%[95% CI (35.79?55.16)] in the females, [p = 0.001, OR = 3.05, 95%CI(1.49?6.26)]. The prevalence of C. trachomatis was 7.90% [95% CI(2.95?16.39)] in the males vs. 12.86% [95% CI (6.05?23.00)] in the females, p = 0.324. The prevalence of N. gonorrhoea was 3.79%[95% CI (0.79?1.08)] in the males vs. 9.86% [95% CI (4.06?19.26)]in the females, p = 0.137. HIV was significantly associated with C. trachomatis, [p = 0.032, OR = 3.18, 95% CI (1.04?9.72)], but was not significant when stratified by gender. HIV was not significantly associated with N. gonorrhoea (p = 0.072) but it was significantly associated when stratified by gender, p = 0.001 for females. There were no significant associations between HIV and age (p = 0.408), even upon stratification by gender. Conclusions: HIV prevalence in this community is high, and corresponds to national figures. However, the prevalence of STIs is surprisingly low as it would be expected to be high in a migrant population. Although communities are exposed to expanding peer-education activities that encourage behaviour change, the prevalence of HIV in this group. There is an urgent need for interventions designed to treat or prevent HIV infection in women generally and in women at high risk. Keywords: HIV prevalence, STI prevalence, antenatal, mining

Jan 1, 2005

By C. F. Strydom

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Self-directed work team concept is the product of relentless performance pressure on American industries during the late eighties and early nineties from other world industrial leaders like Japan. The concept proved to be a successful vehicle by which the Americans could increase their production and improve their safety statistics. The aim of this study is to evaluate the concept as a means to improve the overall performance on South African goldmines. he study is directed by a historical research section, answering questions like: ?Why do we need to change? ?What is a Self-directed work team? ?What are the principle advantages of the concept? ?What are the essential requirements for the concept to succeed? The study also includes an empirical research section that focuses on the current Self-directed work team situation in the South African gold mining industry. The empirical research section is limited to three case studies within Anglogold due to a study period of only six weeks. The mines chosen for the case studies have been labelled Mine 1, Mine 2 and Mine 3. The latter being the base mine allowing for a more in depth study. This includes a perception analysis towards Self-directed work teams within the mine. The study proves the truth of the Latin proverb ?Tempora mutantur, nos et mutamur in illis? meaning ?The times are changing, and we are changing with them?. The chief change catalysts identified are a dwindling gold price and a projected labour crisis. From the study it is evident that the Self-directed work team concept disposes of the critical parameters required for a dramatic improvement in performance. The study also indicates that for the concept to succeed, certain factors like top-level commitment and management-employee trust have to be in place. Sadly, the concluding part of the study proves that very few of the identified critical success parameters are present in the South African gold mining industry. This can serve to explain why the industry only has success with the concept when monetary gain is the chief motivator. The study only focuses on the reasons why the concept is not performing to its full potential and does not wander into explaining the reasons for the current unsupportive milieu in the industry. Self-directed work teams could well rescue the South Africangold mining industry but currently we are driving a square pin into a round hole! [Terminology SDWT?Self-directed work teams AEL?Adventure Experiential Learning ISW?In-stope worker POLC?Plan, organize, lead and control TEC?Total employee costed Silo?The confinement of departments preventing networking JCI?Johannesburg Consolidated Investment Co. Ltd]

Jan 1, 2002

By L Barrere, J P. Sykes, A Trench, R S. Davies

Western Australia (WA), alongside Brazil, has remained at the forefront of the global seaborne traded iron ore market for over 40 years. Despite this apparent stability and strong market position, WA continues to face strong external international supply-side competition, mainly from Brazil, but also periodically from often marginal, non-traditional sources of iron ore. Additionally, WA iron ore supply has undergone significant decadal change internally, both of an evolutionary (brownfields expansion) and revolutionary nature (major new greenfields projects). Since 2006, a new generation of WA-focused iron ore explorers, developers and producers have emerged.The majors, BHP Billiton and Rio Tinto, have expanded mine production to record levels and the Roy Hill project is now approaching nameplate capacity. Fortescue Metals Group (FMG) is, however, the largest new market entrant of the last decade, delivering upon their vision of becoming the ‘new force in iron ore’. Unlike most of the other new WA market entrants, FMG’s operations are substantive. Most of the other smaller, new WA iron ore miners have struggled during the period of falling prices, though it is worth noting that collectively they have made a material supply-side impact during the price boom – typical of marginal supply. Finally there have been some contributions from new magnetite projects, however, the delivery and economics of these projects have not met expectations.In this paper, we touch briefly upon the key global market changes of the last decade, namely China-driven demand growth and the changes to the pricing mechanisms for iron ores – before reviewing the rise in WA iron ore supply in response to these markets. We finish by focusing on the most significant WA-focused supply-side development of the last decade, the rise of FMG as a major new supplier and the strategic situation that facilitated its rise. The unprecedented China-led rise in iron ore prices felled many traditional barriers to market entry into an oligopolistic industry, allowing many new market entrants (in WA and around the world). However, the downturn in iron ore prices resurrected these barriers to entry, with only FMG (thus far) breaking the entry barrier with significant scale. Difficult corporate decisions have been forced upon the smaller WA iron ore miners who, in some cases, will now struggle to further expand, or indeed continue to operate in the longer run.The changes that have taken place over the last decade of WA iron ore production hold insights for other emergent mineral commodity exports from the state. Successful market entry, even when industry barriers are high, does not always require an immediate low-cost production assumption alongside a strong balance sheet. FMG could see a new market, within an established commodity market, target an appropriate and new product at it, overcome temporarily-felled barriers to entry in infrastructure and finance, then innovate and aggressively cut costs ensuring it was behind the barriers to entry when they rose again after the price boom.CITATION:Barrere, L, Trench, A, Sykes, J P and Davies, R S, 2017. New generation Western Australian iron ore – strategic insights far beyond the Pilbara?, in Proceedings Iron Ore 2017, pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By K. Fleck

Energy West Mining Company (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, Utah. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the insitu coal strength and load transfer mechanisms for improving two-seam designs and support systems. Geologic mapping results are also used to predict local stability of headgate and tailgate entries, combining mine roof mapping, stratigraphic profiles of the coal and roof, and depth-of-cover information and dual-seam mine overlays, for use by operations personnel in planning roof and rib support for the retreating longwall sections.

Jan 1, 2012