Search Documents

By P. N. Anyalebechi

Keywords: Aluminum alloy 3004, Solidification rate, Homogenization, Second phase particles The effects of the fineness of as-solidified cast microstructure and temperature on the response of aluminum alloy 3004 to homogenization heat treatment (a.k.a. preheat) have been investigated. The study was conducted at 538oC and 595oC on directionally solidified laboratory-size ingots with a range of solidification rate of 0.10oC/s to 29.4oC/s. Optical and electron microscopy, quantitative image analysis, electrical conductivity, and electron probe microanalysis were used to quantify the effects of the homogenization heat treatment on the microstructure of aluminum alloy 3004. In general, increase in fineness of as-cast microstructure and homogenization temperature enhances the a-transformation reaction, dissolution of Mg2Si, elimination of dendritic microsegregation, and dispersoid formation. The homogenization heat treatment reduces the average size of second phase particles in castings solidified at <1oC/s. However, in castings solidified at above 1oC /s, homogenization causes the coarsening of the second phase particles. Mn in solid solution is independent of homogenization heat treatment temperature.

Jan 1, 2005

By J. Rivoirard

Historically, linear and lognormal krigings were first created to estimate the in situ mineral resources of blocks. Nonlinear geostatistics and indicator kriging were subsequently developed to evaluate also the portion recovered when applying a cut-off on selective mining units (SMUs) within blocks. In practice these methods are generally based either on the Gaussian model with a transformation generalizing the lognormal case or on the indicators above cut-offs. Very often the indicator approach is simplified by kriging separately each indicator, and when starting from a continuous variable, a practical advantage of the discretization into classes lies in the easy treatment of a zero effect and of the high values. However, a number of so-called isofactorial models have also been developed for a discrete or continuous variable, where the full cokriging of indicators (i.e. disjunctive kriging) simplifies to the separate kriging of factors. Moreover, these models are equipped with a change of support, allowing a consistent estimation of recoverable resources on SMUs. Min-Max Autocorrelation Factors (MAF) analysis of the indicators offers a new approach for indicator modelling. In particular the first factor, the one with the highest spatial continuity, can help in choosing the type of model. For example a monotonic experimental first factor can be used directly as the basis of a discrete diffusion model, unless a continuous diffusion model such as the Gaussian model can be used on the original variable. This approach is illustrated on a uranium deposit mined selectively: estimates of recoverable resources by discrete disjunctive kriging and uniform conditioning in a Gaussian model are compared locally to short-term estimates based on two areas densely drilled.

Jan 1, 2014

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By Chris Larsen, Ian Orford, Marilene Renaud, Mike Cooper, Lud Strah

"An AG/SAG mill was commissioned at the Brunswick Mine concentrator in October 1998. This paper discusses the original liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits. The mill liners consist of steel top hat shell liners, steel end liners, rubber grates and rubber lined pulp lifters.Lifter profile and plate thickness measurements were made on monthly shop days. Trends of wear rates were used to project when liners required replacement. Wear profile information was also used to determine where liner re-design would improve wear life or minimize scrap loss. Charge motion simulation modeling was used as a tool to assist liner design modifications.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large underground lead/zinc mine with a nominal production rate of 10,000 tonnes per day. The Brunswick concentrator commenced operation in 1964 with conventional surface crushing followed by rod and ball milling to reduce run of mine ore to the required size to feed two parallel flotation circuits. In 1998 the AG (autogenous grinding) mill was commissioned for a nominal production rate of 9,000 tonnes per day replacing two surface crushing plants, three rod mills and three primary ball mills. In May of 1999 the mining rate was increased and the service of the AG mill was changed to a SAG (semi-autogenous grinding) mill with the addition of 4 inch steel balls (4% volume). The mill operates in closed circuit with 0.66 meter horizontal cyclones to produce a ground product of 90 micron nominal size (K80).The AG/SAG mill liners are steel (Norsteel, chrome-moly steel) with rubber grates and rubber lined pulp lifters.The original liner design was based on studying other AG/SAG mills and recommendations by the liner supplier, Norcast. Design factors taken into account were total cost of lining (including material and labour), protection of mill shell and impact on operating performance."

Jan 1, 2003

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By Associates

The headwaters of Skippers Creek and the Shotover River are reputed to be among the richest alluvial gold catchments in the world. This alluvial gold has no doubt been derived from reef systems similar to, and associated with, the Bullendale lodes. Physiographically the prospect covers steep ridges and deeply incised gullies between the Richardson Mountains in the west and the Harris Mountains in the east. Vegetation is mainly tussock with bush either side of Murdochs Creek. Access to the area is by metalled road to Skippers and then by 4WD track to Bullendale. Alternatively the prospect area can be reached by helicopter from Queenstown in around ten minutes.

Jan 1, 1992

The underwater test method for the determination of energy content of explosives is a very useful method. It’s also the only one which can separate shock and gas heave energies from each other. The total energy can be determined as a sum of these partial energies. Because of this special feature, the test method can be used to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the gas heave energy is a very important feature for the blasting explosives. The goal of this study was to find out the effects of aluminium and sodium perchlorate increments to the shock, gas heave and total energy values of an emulsion explosive and detect the particle size effects of two different aluminium powders to the total and partial energies as well. Both partial energies as well as the total energy were observed to increase linearly as a function of aluminium (A-80) concentration. The fine aluminium powder (A-100) (6%) also seemed to increase the shock energy of the explosive slightly whereas the gas heave energy was observed to remain unchanged to compared to the normally aluminazed (A-80) (6%) emulsion explosive. Therefore the fine aluminium powder also increased the total energy, but only very silightly. The fine aluminium powder can probably take apart to the chemical reactions more easily during the detonation. (3%) of sodium perchlorate (NaClO4) mixed with (6%) of (A-80) aluminium powdered emulsion explosive was observed to effect to the gas heave energy content of the explosive, but only very slightly. The shock energy was observed to remain unchanged.

Jan 1, 2005

By N Weerasekara, M Powell, P Toor

The effect of liner wear on SAG mill performance has gained much attention in recent years. It is commonly observed that the three key performance criteria of SAG milling; throughput, power and product size all improve as the liner wears.The increase in throughput is generally ascribed to the increase in the grate apertures and the increase in mill volume due to the wear of these components. Whilst the decrease in product size is attributed to the reduction in lifter height and angle, resulting in more breakage by means of attrition and abrasion.Though it is widely acknowledged that the wearing of liner components such as Lifters, Plates and Grates have a significant impact on mill performance, their individual contribution to changes in mill performance has been unclear, and resultantly lead to questions like; what percentage of the throughput increase can be attributed to the increase in mill volume (plate wear)? and how much can be attributed to the increase in grate aperture (grate wear)?It has been found that through the use of grinding surveys, analysis of production data and JKSimMet it was possible to separate the effects of changing liner profile, increasing mill diameter and increasing grate aperture on the mill performance allowing for the quantification of each.The outlined methodology allows for both troubleshooting of problem liner components which reduce milling efficiency in their wear life as well as providing a basis for a more quantitative approach to liner design and reline scheduling.CITATION:Toor, P, Powell, M, Hilden, M and Weerasekara, N, 2015. Understanding the effects of liner wear on semi-autogenous grinding mill performance, in Proceedings MetPlant 2015, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty. Ltd. differ supstantially in their characteristics. Knpwledge of performance not only enables comparison and promotes better control, but also provides the means for predicting results.Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep). Results for Baum jigs, a Chance cone, heavy medium cyclones, and water washing cyclones were examined. The efficiency factors derived from the probable error were applied to the float and sink analysis, mathematically simulating operating conditions. This method was applied to the Balgownie seam.The Balgownie seam lies between the Bulli and Wongawilli seams in the coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits rather difficult washability characteristics, due to a comparatively high middlings content. These properties and the relatively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique.Applications of result forecasting are listed.

Jan 1, 1971

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

Copper Recovery from Printed Circuit Board by Carbonisation

Sep 13, 2010

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year&apos;s total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state&apos;s well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma&apos;s producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year&apos;s total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world&apos;s deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year&apos;s total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state&apos;s well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma&apos;s producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year&apos;s total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world&apos;s deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Richard Hosley, James Daley

Every grey haired member of the explosive’s industry has said at least once, “We have to get some younger blood into our industry, I might want to retire someday.” And many a youngster who loves to see explosions has wondered how to get involved in such an exciting, yet intimidating, industry. While there are many answers to these questions, an internship program is a great answer to both

Jan 1, 2014

By M J. Bourassa

In addition to the geologic risk of a particular project, the criteria that an international exploration company (æIECÆ) utilises when making an investment decision in a particular country should also include a critical analysis of the political, judicial and fiscal regime of the host country. A key investment criteria of an IEC is mineral tenure and the security and continuity of that mineral tenure under the host countryÆs existing legal system as well as the host countryÆs overall legal, political and fiscal framework, the latter of which can affect the projectÆs overall economic viability in a number of ways. The authors, Steve Vaughan and Michael Bourassa of Aird & Berlis, Toronto, Canada, have taken the position that developing an understanding of a countryÆs legal tradition is a crucial first step in analysing the mineral regulatory regime of a particular country. This paper continues their efforts to overview the most recent legal trends affecting the worldÆs mineral industry and attempts to analyse, categorise, compare and contrast differing legal systems, cultural backgrounds and economic philosophies relating to the development of mineral rights in Pacrim countries and the resulting commercial, legal, and political framework which ultimately drives the relevant mineral legislation. For the convenience of organisation of this analysis, the authors have divided the Pacrim countries into four smaller groups, firstly, on the basis of their legal tradition and, secondly, by their geographic location:Common Law Countries: USA, Canada, Australia and New Zealand; Spanish Civil Code Countries: Mexico, Central America (Panama, Nicaragua, El Salvador, Guatemala), South America (Chile, Peru, Ecuador, Colombia). Communist or Former Communist Countries: Mongolia, China, Russia. Countries of the Pacific Southwest: Phillippines, Indonesia, Malaysia, Indo-China (Vietnam, Laos, Cambodia, Thailand), Papua New Guinea. The discussion starts with an analysis of the various types of legal regimes, attempts to classify or categorise them, reiterates the necessity for the rule of law and those factors which encourage mineral exploration and development and discusses and recommends the expansion of a practical country competitiveness rating system developed by the Fraser Institute. In addition to the fundamental issue of mineral tenure û what it is and how secure it is û the paper discusses how different legal systems have shaped different approaches taken by individual nations to attract foreign mineral investment. The paper analyses the best practices and experiences accumulated in different Pacrim countries with varying legal traditions and identifies a practical country competitiveness rating system which the authors believe should be expanded to cover all minerally endowed countries. This rating system will permit countries to identify their mineral regime weaknesses and adjust their legal systems to better attract mineral investment and will also permit exploration and mining companies to compare their jurisdictional choices with those selected by their competitors.

Jan 1, 1999

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

Three large deposits of good quality lignite were located and delineated in the Central Otago region between October 1978 and July 1979. The program was initiated and funded by Mines Division of the Ministry of Energy as part of the national Coal Resource Survey. The exploration work was carried out by Lime and Marble Limited on a contract basis (Bowman, 1980). The three deposits were all potentially mineable by open cast methods and possessed combined indicated and, inferred reserves in the order of 1000 x 106 tonnes. They ranked with the previously discovered Eastern Southland 1ignites and as such constituted an important national energy resource. Fifteen months later a second more detailed investigation of similar duration was undertaken by the Liquid Fuels Trust Board (LFTB). The objective was to upgrade and refine the geological data base of all of the nine South Island 1ignite deposits in order to make preliminary economic assessments of their potential. Again Lime and Marble Limited acted as the exploration operator (Bowman, 1981a, 1981b, 1981c).

Jan 1, 1983