Search Documents

By L. W. Berger, R. I. Jaffee, D. N. Williams

The effects of hydrogen on the properties of binary Ti-A1 alloys containing 2.5, 5, and 7 pct aluminum and ternary alloys of the same compositions with added interstitial elements oxygen, nihrogen, and carbon were studied. Aluminum increases the apparent hydrogen solubility of the a-phase, resulting in a marked increase in resistance to impact embrittlement. In the Ti-5Al and Ti-7Al alloys, for example, the addition of 180 and 305 ppm hydrogen, respectively, did not cause embrittlement, while unalloyed titanium was embrittled by as little as 75 ppm. The role of aluminum in increasing hydrogen solubility of the a-phase probably accounts for the excellent hydrogen tolerance of a-ß alloys containing considerable amounts of aluminum. There is some evidence that aluminum retards the rate of hydride precipitation. If so, these alloys may be susceptible to slow-strain embrittlement. UNALLOYED a-titanium is extremely sensitive to small amounts of added hydrogen in that there is a marked decrease in notch properties. For example, as little as 100 ppm hydrogen is sufficient to lower the room-temperature notch-impact strength from over 100 to less than 20 in.-lb.' This loss of impact Strength has been associated with the Presence of hydride phase in the microstructure. Hydrogen in the amounts encountered in commercial practice

Jan 1, 1959

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By Gilson Neves da Silva, Luciana Sgarbi Rossino, Adriel de Brito Maciel Trindade

O objetivo deste trabalho foi de analisar a influência da variação de manganês e cromo na resistência ao desgaste abrasivode aços austeníticos ao manganês aplicados em britadores de minério e verificar mecanismos de encruamento. Este material possui grande importânciatanto para o setor de mineração quantopara a economia do país. Para tanto, produziram-se ligascom teor de manganês (Mn) variando entre 12 e 21%, contendo cromo (Cr) entre 0,31 a 2,06 %. A resistência ao desgaste foi determinada através da realização de ensaios de micro-abrasão por esfera fixa. Para a análise dos mecanismos de encruamento, realizaram-se ensaios de impacto por martelamento seguido de metalografia ótica e perfil de dureza. Os resultados evidenciaram que o aço com percentual mais elevado de manganês com adição de cromo possui maior resistência ao desgaste abrasivo. Observou-se que o mecanismo atuante no encruamento dessas ligas é maclação de deformação, podendo elevar a dureza destes aços em valores quatro vezes maiores que sua dureza inicial. Conclui-se que o teor de Mn e Cr presente nesses aços influenciam na resistência ao desgaste abrasivo, sendo o Mn de maior influência.

Mar 1, 2019

By A Goldstone, T Maton

The Golden Cross Mine is located on the North Island of New Zealand, at the base of the Coromandel Peninsula, approximately 8 km northwest of Waihi. The project is operated as a Joint Venture with Coeur Gold New Zealand holding 800/0 and Viking Mining Limited with a 20% interest. The past open-pit and underground gold and silver producer has been in the reclamation phase of the operation for approximately 2.5 years and is now nearing completion. Although rehabilitation of the site is a regulatory requirement, the Closure Plan has been enhanced by the ongoing commitment of the Joint Venture to establish a sustainable land use for the site by commissioning engineered facilities designed to last for perpetuity. The Joint Venture identified six significant design features that were key to successful rehabilitation. These were the controlled placement of acid generating waste rock into engineered disposal sites; the design and placement of sealing layers over the waste rock disposal sites; the design and construction of diversion drains; the establishment and management of vegetation to protect the oxygen diffusion layer; a partial capping of the tailings to accelerate consolidation adjacent to the tailings dam embankment, and the implementation of a cyanide recovery circuit to recycle cyanide from the tailings prior to disposal. Another key to success for the project involved genuine consultation with all parties participating in the planning, evaluation, and consenting of the closure process at Golden Cross. The local and regulatory community has been widely represented in the Joint Venture's operating and closure plans throughout the history of the mine. Participants include: Regional and District Councillors and staff members, professional peer reviewers, environmental groups, local residents of the valley, and Iwi. This overall commitment to the project has resulted in a world-class rehabilitation program for the first modern metal-mine closure in New Zealand and we believe that collectively, the work done at Golden Cross is helping to set a standard for the success of future programs within the extractive industry.

Jan 1, 2000

By K Palmer, G J. Artmont

Alluvial gold is an ideal exploration tracer to bedrock source and indicator of bedrock mineralisation style because: (i) gold occurs in a wide range of deposit types, (ii) primary composition is sensitive to style of mineralisation, and (iii) it is a heavy resistate mineral that is readily preserved and easily sampled. In regional exploration of the Central Ranges of Irian Jaya, alluvial gold mineralogy has been applied to maximise the information return from panned concentrate sampling and to focus exploration effort. Primary gold is a solid solution of Au+Ag¦Cu¦Hg, ¦ trace Pd, Te, and Sb. In general Ag¦Hg increase and Cu decreases with inferred decreasing temperature of formation, and gold from particular mineralisation styles has signature compositions that can be used as indicators of bedrock mineralisation type. Furthermore, the abundance of alluvial gold is an indicator of the economic potential of a catchment. The convergent continental-oceanic plate geology of the Central Ranges is conducive to a wide range of mineralisation styles. Mineralogy of gold in ophiolite, skarn, porphyry, mesothermal vein and possible VHMS environments is characterised from alluvial and bedrock samples, and the use of gold mineralogy in prospecting at regional scale through prospect definition to drilling is demonstrated.

Jan 1, 1995

By F. A. Olson, J. S. Cho, M. E. Wadworth

An infrared study of the states of hydration of MgSO4 revealed a hitherto unreported metustable dehydration state in the temperature range just below that of the stable anhydrous salt. Infrared, thermogvavimetric, and X-ray studies indicated that the state had bisulfate and hydroxide characteristics. A formula fitting all of the experimental evidence is hydrogen-bonded Mg(OH)HSO4, or possibly the chemically equivalent 1/2 Mg(HSO4)2. Mg(OH)2 Infrared spectra of the 7, 6, 1, and OH2O states of hydration are given as well as the spectra of the newly found state which is called the bisulfate state in this paper. Thermogvavimetric studies as a function of water-vapor pressure gave an enthalpy value of 16 cal per mole, and 25 eu for the conversion of the bisulfate state to that of the anhydrous salt. The free energies of the transition varied from 1.76 to 0.18 kcal per mole as the transition temperature varied from 279° to 336°C. The bisulfate state is believed to be of importance in catalytic dehydration phenomena using MgSO4 and may be of interest because of properties in sulfating reactions differing from those of the monohydrate. Also, an analogous state may exist as a hydration state of other sulfates. ANHYDROUS magnesium sulfate is a catalyst with a high degree of specificity for the dehydration of secondary alcohols.1'2 The only product obtained at the usual operating temperature range of 360" to 400°C other than the corresponding olefin is water. Thus, the bonding of water to the anhydrous salt as well as an understanding of the hydration states of MgSO4 became of interest in attempting to understand the catalytic mechanism better. In the process of this study using infrared, X-ray, and thermogravimetric analyses a dehydration state not previously reported was found. Proof of its existence, the nature of the state, and its role, if any, in the catalytic mechanism then became of interest. This paper is concerned principally with the first two aspects of this problem. Magnesium sulfate forms many hydrates, of which the monohydrate and heptahydrate (Epsom salts)3 are most important. Other hydrates4 are known with 1-1/4,5 l-1/2, 5 2, 4, 5, 6, and 12 H2O's. The hydrates with 1-1/4, 1-1/2, 2, 4, and 5 HzO's are unstable. The anhydrous salt is very stable thermally and has a strong affinity for water. It can be heated without additional decomposition to about 800°C.' At 900°C noticeable decomposition takes

Jan 1, 1964

By Cotton R. E, Cox R

Digger Rocks is one of several nickel-bearing sulphide deposits localised within komaLiitic volcanics of the Forrestania Greenstone Bell within the Archaean YiIgam Block of Western Australia. Exploration and evaluation to April 1990 have delineated a resource, at a nominal cut-off grade of 0.5 per cent Ni, of 1.9 Mt at 1.1 per cent Ni within a lensoid sulphide body which strikes NW, dips 50°SW, and occurs at a depth of 30 - 110 m below surface. There has been no production from any of the Forrestania nickel deposits to-date. The deposit, comprising both disseminated and massive sulphides, has maximum dimensions of 400 m strike, 115 m vertically and 90 m true width. Generally the massive sulphides occur at the base of the disseminated sulphides, on or close to the base of the Digger Rocks dunite. The two main massive sulphide lenses have maximum dimensions of 120 m strike, 75 m vertically and 16 m true width (northern lens) and 60 m strike, 25 m vertically and 4 m true width (southern lens). The average grades of the massive and disseminated sulphides are 5.9 per cent i and 1.2 per cent i respectively. The massive sulphides generally have sharp hangingwall and fOOlwall contacts and display strong internal grade anisolropy.The massive sulphides are mainly within the supergene zone and consist of violarite, pyrite and marcasite. The disseminated sulphides are mainly within the primary zone and consist of pentlandite, pyrrholite, pyrite and minor chalcopyrite. Alteration zones, up to six in number, are complex in detail. The sulphides are capped by an average of 30 m of sub-economic, leached, siliceous, oxidised material.A genetic model for the deposit is described which places Digger Rocks in Category 2 (sulphides in large layered dunite bodies) of the latest classification of komatiitic nickel sulphide deposits in the Yilgam Block of Western Australia by Hill and Gole (1990).

Jan 1, 1992

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By W. T. Olsen, R. Ulcer

WHEN a liquid alloy freezes, the solid first formed usually differs widely in chemical composition from that last formed, so that there is segregation in the alloy as cast. For example in the copper-nickel system (fig. 1) the first solid formed from a liquid containing 55 atomic pct Cu may contain as little as 38 pct Cu, while the last must contain well over 55 pct. Three factors may act to decrease segregation from the maximum possible. 1. Diffusion in the cooling solid tends to make the phase homogeneous, decreasing segregation. This may be important at slow rates of cooling. 2. Segregation is impossible without diffusion in the liquid. At extremely rapid rates of cooling there may not be enough time to allow maximum segregation. 3. Supercooling delays nucleation to temperatures well below the liquidus thereby decreasing segregation. Hence the first nucleus in the copper-nickel system may contain well over 38 pct Cu. At sufficient supercooling the first nucleus may form below the solidus, in which case there is no reason to expect any segregation whatever. From these considerations, we could predict that at sufficiently low rates of cooling the alloy would be unsegregated because of factor 1 and at sufficiently high rates of cooling there should also be no segregation because of factors 2 and 3. Considerable segregation should occur only at intermediate rates of cooling. We have demonstrated experimentally that segregation can be completely suppressed by rapid rates of cooling. For the alloys studied, however, these rates are too great to be attained in any commercial practice. An alloy of 55 atomic pct Cu, 45 atomic pct Ni was frozen by cooling at varying rates. The degree of segregation in the solid was determined by X-ray diffraction photographs. Slow rates were obtained by slowly cooling the furnace containing the liquid alloy; fast rates by pouring or ejecting droplets of the alloy into water or iced sodium hydroxide solutions. The cooling rate of the droplets can be cal-culated from their dimensions by assuming reason- able values of thermal conductivity.' The experi-ments were repeated with an alloy of 16.5 pct Cu and 83.5 pct Au. A single experiment also showed a 50 atomic pct Bi-Sb alloy had no segregation at the most rapid quench. The position of back-reflection X-ray diffraction lines is a highly sensitive function of the lattice constant, which in turn depends on the chemical composition of the phase. A phase of varying composition will give broad diffraction lines. By measuring the edges of these lines and making suitable corrections for intrinsic line width, it is possible to determine the range of lattice constants represented. These can be converted to chemical compositions from a lattice constant vs. composition curve. Results are shown in table I. In the copper-nickel system the greatest segregation is found at the slowest cooling rates, where the lowest percentage of copper theoretically possible is found. In the copper-gold system, on the other hand, the degree of segregation is decidedly less at the slowest rates of cooling, being greatest at 11,100°C per sec. At no rate is the theoretically lowest percentage of copper (12 pct) found. At the rates of cooling found in sand and die castings the degree of segregation is large and depends little on the rate of cooling. Acknowledgment Most of the material in this paper is abstracted from a thesis presented by William T. Olsen, Jr. in 1948 in partial fulfillment of the requirements for the degree of Master of Science at the University of California.

Jan 1, 1951

By D. R. Hack, N. M. Sirakov, M. L. Feves, M. Iwanowski

This paper presents a new approach capable of volume calculation of 3D reconstructed geological objects. The method is based on a well-known concept that states the volume of an object can be computed as the limit of the sum of the area of infinite number of sections, which cut the 3Dobject. Since shortage of input data about the geological objects usually exists, Mathematical Morphology and polynomial interpolation are employed to generate a set of intermediate sections between the set of initial sections. A Mathematical Morphology tool is applied to compute the area of the two of sets initial and generated 2D sections. Regularities together with Delaunay Triangulation are employed to perform 3D reconstruction. A formula is developed on purpose of volume calculation of the reconstructed objects. A set of ten theoretical, electrical resistivity cross-sections were generated and used to perform an experiment to show the capability of our approach to estimate the volume of complex 3D geological object in case of sparse 2D sections. The volume determined using the morphological approach presented in this paper show good correlation with the volume of the original input object. Advantages and disadvantages of our volume calculation approach are discussed in the conclusion of this paper. Keywords: electrical resistivity, sparse 2D sections, geological objects, smooth 3D visualization and volume calculation.

Jan 1, 2003

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Altair Lúcio de Souza

A laminação de tiras a quente com laminadores Steckel tem como característica um perfil de temperatura mais baixa nas pontas sendo este um dos motivos que geram cargas de laminação muito mais altas nesta região. A carga de laminação elevada tem como consequência no processo a geração de desvios de planicidade e o alto risco de rompimento do material nos passes finais de laminação. Este trabalho tem como objetivo demonstrar os benefícios da utilização da estratégia de Tapering para a laminação de tiras de espessura fina em laminador Steckel. Foi feita a comparação das cargas de laminação do material laminado e o acompanhamento dos resultados de planicidade obtidos antes e depois da implantação desta função. Ao fim do trabalho verificamos que a estratégia de Tapering é essencial para o processamento de materiais finos com laminadores Steckel.

Jul 30, 2018

By J H. Park, M J. Lee

Because the environmental problems are occurred by greenhouse gases such as CO2, the industries have tried to increase electric motor efficiency to reduce CO2 emissions. A core material of electric motor is high-silicon electrical steel. The ferrosilicon (FeSi) alloy, a raw material for the production of electrical steel, affects the electric properties of silicon steel. The main impurities such as Ca, Al and Ti make inclusions or precipitates that causes core loss. The slag treatment has been widely used to remove impurity elements. Thermodynamic principles for the refining of several impurities, specifically Ca and Al, have been investigated, whereas thermodynamic behaviour of Ti has not been fully understood yet. Therefore, in the present study, the titanium distribution ratio () between ferrosilicon and CaO-SiO2-Al2O3 slag system at 1773 K was investigated. The results show that is influenced by both the basicity and stability of titanium ion in the slag. Specifically, exhibits a minimum value at about C/S=0.7 indicating a shift in the titanate structure unit from [TiO5]-square pyramid to [TiO4]-tetrahedron because of lack of Ca2+ ions in a C/S<0.8 region, contributing to an increase in titanate capacity and .

Jun 19, 2024

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By J R. Goff, R Carver, D S. Sheppard

The REGCHEM (Regional Exploration Geochemistry) stream sediment geochemistry database of open file mining company data, managed by GNS Science, was recently made accessible via the internet (http://maps.gns.cri.nz/website/minmap/). REGCHEM provides coverage of selected elements in mineral rich areas of New Zealand. Analysis of REGCHEM data highlights problems with inconsistencies between different surveys in terms of sampling methods, number and types of elements analysed, analytical techniques and detection limits. New, consistent multi-element geochemical surveys with national coverage are required. To test sampling, analytical and data treatment techniques for the new surveys, a pilot stream sediment geochemical survey was carried out in the Thames area, Hauraki Goldfield. Seventy samples were collected in an area of 220 km2 representing about one sample every 3 km2. The samples were analysed for 50 elements, mostly by XRF. &nbsp; Regional patterns are apparent in the concentrations of some elements. Several elements, such as As, Cd, Cu, K, Pb, Sb, Se, and Zn exhibit anomalous concentrations mainly in the western part of the study area, related to Au-Ag-Zn-Pb-Cu epithermal quartz veins and porphyry Cu occurrences in hydrothermally altered andesitic terrane. &nbsp; Mercury is anomalous in southern samples, reflecting cinnabar occurrences in the Kauaeranga valley (eg Mangakirikiri), and the occurrence of cinnabar as a late stage mineral in some of the Thames epithermal veins. Ba and U are anomalous in the eastern samples, and these anomalies are probably related to the presence of rhyolitic rocks in the eastern part of the project area.

Jan 1, 2006

A computer program for the static load analysis of linear elastic structures is presented. It is the product of a two-year project for the development of a efficient program for the analysis of mine-type structures. The report is divided into two parts. The first part explains the general method of analysis, the computer program organization and the most significant numerical techniques used. The second part is a user manual for the computer program. The FORTRAN IV computer program deck and example problems were transmitted separately to the sponsor. Request for a copy of the program should be directed to the Bureau of Mines, Denver Mining Research Center.

Jan 1, 1972