Search Documents

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By Peter Zhang

Pumpable cribs are being increasingly used in longwall tailgate entries and bleeders for roof support under abutment pressure. Their high peak capacity and confinement-controlled yield characteristics from reinforced-bags make them relatively safe and reliable standing supports for highly productive longwall panels. The pumpability of crib material over a long distance from the surface greatly reduces material handling and makes the underground installation more efficient and flexible. However, the performance of pumpable cribs is dependent upon crib properties, crib pattern, quality of installation, and geological and mining conditions. For proper crib selection and safe support design, it is critical to understand the basic technical requirements and performance of pumpable cribs in longwall tailgate entries and bleeders. Based on more than 10 years of experience using pumpable cribs for longwall standing support, the requirements and performance of pumpable cribs in longwall tailgate entries and bleeders under different mining conditions are presented. Experience shows that the load-displacement curve from full-scale lab testing is a good indicator of pumpable crib suitability for certain applications. Crib peak capacity, stiffness, and residual characteristics define its applicability to certain gate entries and bleeders under different cover depth. Crib pattern and spacing can be determined by abutment pressure level, roof, floor, and rib conditions, local roof stability, and ventilation requirements. To achieve proper in-situ performance, quality control of crib installation is also important.

Jan 1, 2012

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

R. W. Raymond, New York City: In connection with the subject of multiple tuyeres, my attention has been drawn to the practicability of gaining, without the multiplication of tuyeres, the advantages which that measure is intended to secure ; and learning that this had been attempted in the invention of the Gaines radial-discharge or fan-shaped tuyere, I wrote to Messrs. Gustafson Brothers, of Sequachee, Tenn., who manufacture that tugere, for information concerning the invention itself and its performance in practice. To their courtesy I am indebted for most of the facts given below. I present these statements without expressing any personal opinion on the subject (having no personal knowledge of it), for the purpose of bringing this device to the notice of members, and calling forth both criticism and testimony concerning it. Admitting that definite advantages are to be secured by the multiplication of tuyeres, we must still confess that this change involves considerable expense in the increased number of blastpipes, tuyeres, coolers, connections, and pipes for water-circulation. There is, moreover, a serious question involved in the weakening of the furnace-wall by extra perforations. This consideration applies with special force to furnaces already built without reference to such an increase of tuyere-openings. Ledebur, in his Handbuch der Eisenhüttenkunde, says on this point (I translate from the edition of 1893, page 365): "A limit to increase in the number of tuyeres is given, in any case, by the circumstance that the perforation of the wall weakens it; in other words, that there must be left between the tuyeres a mass of masonry sufficient to carry the parts above. In most cases an appropriate number may be secured by giving to the furnace as many openings as there are meters in its circumference at the tuyerelevel. For instance, for a hearth-diameter of 2.5 meters, i.e., a circumference of 7.7 meters, seven or eight openings might be made, of which, however, one would

Jan 1, 1899

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By Ivor Hawkes

This report describes the results of a study to evaluate new design concepts for percussive rock drills that will result in quieter machines. It is shown that by incorporating such features as an efficient muffler, a plenum chamber integral with the machine body, and shroud tubes around the drill rods, etc., noise levels are reduced from about 114 dBA to about 95 dBA with very little change in drilling performance.

Jan 1, 1977

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By Robert L. Frantz

The performances of the three bituminous coal demonstration methane re¬covery boreholes, located in Greene County, Pennsylvania, are reviewed. Development of these vertical holes was largely underwritten by project funds. Reference is also made to an anthracite coal methane project in Luzerne County, Pennsylvania. This involved one vertical hole and was underwritten by a utility company. In addition, an exploratory drilling in the southern anthracite, which provided the project group with coal cores for methane gas analysis, is also cited. The technical and economical data that were gathered from the various methane projects are analyzed. Finally, the advantages and disadvantages of methane recovery by vertical boreholes are assessed.

Jan 1, 1978

By Michael M. Hamilton

In 1984 and 1985 the U.S. Bureau of Mines performed a mineral survey of the South Jackson Mountains Wilderness Study Area covering 60,211 acres of mountainous terrain of Humboldt County in northwestern Nevada. Approximately 550 lode claims have been located within or adjacent to the study area from 1900 to the present. Total recorded production for the area is 28.19 ounces gold, 1,105 ounces silver, 959 pounds copper, 6,016 pounds lead, and 12,446 pounds zinc; an additional two carloads from one mine contained an unknown amount of metal. In early 1986, there were eight active properties with a total of 126 claims. Wescord Resources and Long Lac Exploration (Texas) Inc. are involved in a joint exploration of the Jackson Mountains for volcanogenic massive sulfide deposits. Development at the Claudia mine continues in 1986. Results of the survey indicate that there are no identified mineral resources or reserves within or adjacent to the study area. Twenty-two properties have mineral occurrences containing gold, silver, copper, lead, zinc, iron, antimony, vanadium, and cobalt, with silver, copper, and iron being the most abundant.

Jan 1, 1987

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By Lucas Beirão do Valle

Este artigo visa estudar polímeros como quitosana, amido entre outros com elevada disponibilidade como agentes aglomerantes no processo de pelotização de minério de ferro e discutir sobre o impacto da sua utilização. Os polímeros foram testados preliminarmente no teste de bancada (teste em pneu), para medir qualitativamente a tendência de aglomeração. Os polímeros com melhores resultados foram testados em escala piloto, que simula o processo industrial. Nos testes preliminares, o amido gelificado apresentou os melhores resultados de resistência física de pelotas verdes e secas. Entretanto, no teste piloto o amido não foi capaz de controlar a umidade superficial. Os outros polímeros não foram considerados promissores, principalmente devido ao controle da umidade superficial.

Aug 1, 2018

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

I.T.H. Drilling has been accepted as a tool used daily for both production and service work in Australian underground mines. For this reason, it is of interest to examine the rigs and drilling equipment in use to do this work, also to review the technique necessary to ensure that this drilling is done efficiently.

Jan 1, 1978

By D. F. Atkins, B. A. Rogers

The constitutional diagram presented herein is relatively simple. Complete mutual solid solubility exists for an interval below the solidus line, a continuous curve with a flat minimum near 22 pct Cb and 1740°C. Upon cooling, the solid solution breaks up, except at the columbium-rich side, from two causes: zirconium-rich alloys transform under the influence of the ß-a transformation in zirconium; alloys of intermediate composition decompose into two solid solutions below 1000°C. The combined effect is the formation of a eutectoid at a temperature of 610°C and a composition of 17.5 pct Cb. The eutectoid horizontal extends from 6.5 to 87.0 pct Cb. Some age hardening effects have been observed in the zirconium-rich alloys but the positions of the solvus lines remain uncertain. IN recent years, zirconium has been produced in much larger quantities than were available previously. Correspondingly, the incentive for studying its alloy systems has increased, as the number of recent publications on alloy systems testifies. However, only a partial diagram of the Zr-Cb system has been published and relatively few references have been made to alloys of the two metals. Hodge' investigated the Zr-Cb system up to about 25 pct Cb. His data on melting points were not sufficiently numerous to distinguish with certainty between the alternatives of a narrow eutec-tic horizontal and a wide flat minimum in the solidus curve. Although Hodge considered his results on transformations in the solid state to be only tentative, he suggested that the eutectoid in the zirconium-rich alloys lay at about 625 °C and 10 pct Cb and estimated that the solubility of colum-bium in zirconium at 625 °C was near 6 pct. According to Simcoe and Mudge,2 less than 0.5 pct Cb is soluble in zirconium at 800°C. These authors observed an increased strength in both the 0.5 and I pct Cb alloys made with hafnium-containing zirconium. According to Keeler,3 the strength of zirconium is increased by addition of columbium to a content of at least 3 pct. Keeler' also observed a maximum in hardness at about 10 atomic pct Cb and commented on the brittleness of alloys of this composition. Anderson, Hayes, Rober-son, and Kroll5 investigated the tensile properties of Zr-Cb alloys containing 5.1 and 12.9 pct Cb at room temperature and at 343°C. The 12.9 pct alloy had a high tensile strength at room temperature but also a low percentage of elongation. All alloys had high elongation at 343 °C. Littona measured strength and elongation values of annealed alloys containing up to 27.5 pct Cb and found low elongation values for all of the alloys of high columbium content. Some observations on the resistance of Zr-Cb alloys to corrosion in water at high temperature have been published by Lustman, De Paul, Glatter, and Thomas' who found that additions of columbium up to 1 pct had only a minor effect on the corrosion resistance of zirconium. Preparation of the Alloys Raw Material: Zirconium of a relatively good grade was available for making the alloys. It was obtained as scrap pieces that had been left over from an operation that included production by the iodide process, melting under a protecting atmosphere, and fabrication to plates. The individual pieces had hardness values of 24 to 32 Ra and a typical analysis is shown in Table I. The columbium also was scrap trimmed from sheets. It was furnished by the Fansteel Metallurgical Corp. and had a high ductility but its analysis was known only approximately. The metal probably contained about 0.5 pct Ta, perhaps 0.25 pct C, and a few hundredths percent each of iron, silicon, and titanium. Melting: The alloys were melted in a tungsten-electrode copper-crucible arc furnace similar to units that have been described recently in the metallurgical journals.'.' The crucible of this furnace is provided with a cavity in which a getter charge can be melted before the melting of the alloy charges. Hardness measurements on the ingots indicate that the getter charge takes up a considerable fraction of the oxygen and nitrogen from the helium atmosphere of the furnace. The alloys used in the investigation are given with their intended compositions, hardness, and melting points in Table 11. Fabrication: All alloys of the Zr-Cb system appear to be amenable to fabrication. At least, all of the compositions listed in Table II could be reduced to wires in a rotary swaging machine. The starting material was either slabs cut from ingots and ground by hand to rough cylinders or narrow strips trimmed from sheets made by cold rolling slabs. However, not all of the alloys could be fabricated satisfactorily by the same method. From 0 to 4 pct Cb and from 20 to 30 pct Cb or more, the alloys could be swaged cold from ¼ in. cylinders to 0.80 mm wires with only one intermediate annealing, sometimes with none. From 40 to 90 pct Cb, the alloys were difficult to swage either hot or cold but could

Jan 1, 1956

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991