Search Documents

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate process plants requiring high throughputs presents unique metallurgical environmental and sustainability challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life-of-mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy and high ore variability, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, high capital and operating costs, worldwide constraints on resource availability, complicated regulations in emerging economies, changing demographics of mining operations with ever-changing cultural or community issues and the urgent need for a better assessment of project viability to reflect the dynamics of present mining scenario. Developing breakthrough solutions to these problems is the key to success of any new project and maintaining profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial along with the need for a more lateral thinking, strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex metallurgical problems.IntroductionThere is a plethora of challenges in developing new ore bodies. The metallurgical complexity of these deposits has increased significantly due to the need for mining lower grade ores along with the presence of deleterious elements that have environmental and processing implications. In addition, many of the mining projects are capital intensive due to high throughput requirements to be economical along with the need for building infrastructure due to remote locations, while operating costs steadily increase due to high reagent, energy and labour costs, increased state royalties and community obligations, to name a few of the key factors. There is also scarcity of water in many regions requiring the use of sea water or brackish water, which has both environmental and metallurgical implications. The shortage of qualified technical manpower adds significantly to the woes of many mining companies. Considering these multiplicity of challenges, it has become imperative for many mining companies to be innovative in addressing these issues."

Jan 1, 2015

By Jeffiey B. Austin, Maurice Tagami

"The ores of the Iberian Pynte Belt are typically massive sulphide ores with very fine grained mineral textures. EuroZinc Mining Corporation is currently evaluating one of the massive sulphide deposits located near the town of Aljustrel, in South Central Portugal. The deposit contains significant grades of lead, zinc and silver. The ores are comprised solely of sulphide mineralization consisting of pyrite, sphalerite, galena and some secondary copper minerals. Liberation requirements for these ores are typically 22 to 25 microns. A selective flotation process has been utilized to produce separate lead and zinc concentrates for sale to off-site contract smelters.This paper outlines the process test results and describes the process parameters required to optimize the process parameters. Ths test program has been conducted in support of the re-opening of the facilities in Aljustrel. The 3500 tpd mining and milling facility was commissioned in 1990 and operated for 18 months before closing. The previous facility was designed to produce three products using a selective copper-lead-zinc flotation process. EuroZinc Mining Corporation is proposing to re-open the operation, selectively mining from a lead-zinc phase of the massive sulphide deposit and produce only lead and zinc concentrates.Results are presented and discussed.PROJECT HISTORY AND CURRENT PROJECT OBJECTIVESThe EuroZinc Aljustrel Project is a potential major producer of lead, zinc and silver located in the Iberian Pyrite belt of south-central Portugal. The town of Aljustrel is historically associated with mining dating to the time of the Romans. The area is rich in pyrite deposits, and sections of the pyrite deposits contain significant zones of copper, lead, zinc and silver. Mining in Aljustrel during the last century (1900’s) included a major pyrite mining operation, which produced feed for sulphuric acid production. Pynte mining operated from the 1930’s to the early 1970’s and a short-lived base metal operation from 1989 to 199 1."

Jan 1, 2000

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By Steve Skelhorn

Edmonton South LRT is the latest expansion of the Subway system in Edmonton, Alberta, Canada: Consisting of twin 5.8m segmental lined tunnels, 280m long, driven by a Lovat EPB machine. The key challenges were as follows. A 6% downhill grade. Tight radius curves of 250m.Overlying structures within 3m of the tunnel. Strata consisting of sand above the water table, glacial tills and bed rock below the water table. Located within The University of Alberta Campus and adjacent to a hospital. Northern Alberta climate with winter temperatures routinely falling below—minus 30 degrees Celsius. This paper provides a case history and outlines the challenges involved in completing this project.

Jan 1, 2005

[Page Officers of the Institute 5 Minutes of Twenty-first Meeting 9 The U. S. Fuel Company's Tipple at the Hiawatha Mine John M. Jennings 11 Some Experiences With Mechanical Loading in Central Pennsylvania¬ O. G. Sharrer 13 Mechanical Loading Underground- A. W. Dickinson 25 Operation by Long-Face Conveyor Method at Sweetwater Mine Glen A. Knox 39 Discussion of Mechanical Loading 44 Discussion-Safety in Mechanical Loading 45 New Steel Tipple, Spring Canyon, Utah- G. A. Murphy 46 A Theory on the Cause of Spontaneous Combustion-C. P. Crawford... 48 Rock Dusting in the West-D. Harrington 50 Mudite-L. C. Clare 57 Discussion of Harrington's and Clare's Papers 59 Material for Rock Dust-Prepared Discussion-Edward K. Judd 60 Tipple and Mine of the Columbia Steel Corporation-T. C. Harvey 63 Mechanical Stoking of Domestic Fuel-Joseph Harrington 67 The Garrison Automatic Domestic Stoker-Lloyd Garrison 70 Discussion of Domestic Stokers 71]

Jan 1, 1925

By Silvano Morelli, Giovanna Cassani, Renzo Bindi, Antonio Nicola

More than 70 km of main line and service tunnels have been excavated to date for crossing the Apennines between Bologna and Florence. A new design and construction approach, known as Analysis of the Controlled Deformation in Rock and Soils, (ADECO-RS), was adopted to tackle the extreme heterogeneity of the ground and the particular stress-strain conditions. The goal of this system is to obtain constant and predictable full section advance rates, even in very poor geology, with the highest possible level of safety and reliability. The execution of this gigantic project required the mobilization of 21 job-sites, with the concurrent operation of 30 excavation headings. The global production rates confirm the high quality of the design and the high level of industrialization reached during the construction stage, levels not previously obtained in similar conditions, using other approaches such as NATM.

Jan 1, 2003

By Alejandro R. Alonso, Lizet Alvarado, Gretchen T. Lapidus

"Cobalt and lithium recovery from spent Li-ion secondary batteries has been increasingly studied in recent years due to the high value of both metals and the low proven reserves for lithium. The standard method employed until now has been the deactivation and crushing of the batteries, followed by leaching of the L1C0O2 spinel from the battery cathode using acid solutions, such as 1.5 to 2.0 M HC1 or H2SO4, in a temperature range from 120°C to 250°C. Once leached, the cobalt is separated by electrodeposition and the lithium by precipitation, using large amounts of carbonate to bring the solution to alkaline pH values. In the present work, citric-thiosulfate solutions are used for the spinel leach at room temperature, favoring a reductive environment at room temperature, which stabilizes the cobalt(II) as cobalt citrate and lithium(I) at pH 5, and recovers approximately 99% of both metals.IntroductionThe Li-ion batteries industry has become an important economic sector in recent years. This type of battery is the most promising system for energy storage, because of its high efficiency in charge-discharge cycles, and its adaptability to many configurations. The demand will probably increase because of the need for mobile energy sources in many types of devices ranging from cell phones, tablets, and laptops to medical, navigation and sophisticated communication equipment and even in automobiles.One major problem related to the use of these batteries is the method employed for recycling the components, mostly cobalt and lithium. Currently, there are two processes employed on an industrial scale: the Sony/Sumimoto process, used since 1990 [1] and the Toxco Process [2]. In the first case, incineration is used to open the batteries and at same time volatilize the organic solvents. After that, the metals (copper, iron and aluminum) are physically separated. The cobalt and lithium are recovered as oxides and then thermally treated in order to recycle them for new batteries manufacture."

Jan 1, 2012

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1990

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972