Search Documents

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By S. D. Zhang

The first reinforced earth railway bridge abutment in China has been successfully constructed of September, 1985 under the supervision of the Reinforced Earth Researth Group of Shanghai Institute of Railway Technology. In order to verify the reliability of the designed structure and its behaviuors, the 1:10 reduced scale model tests in laboratory and field tests on the actual structure during construction were proceeded. Various loads of different positions were charged, the vertical and lateral earth pressure in the filling soil, the stresses developed in the reinforcements, and the deformations of the models or the actual structure were recorded in those tests. The behaviors recorded are presented and discussed in this paper.

Jan 1, 2010

A unity of viewpoint emerged from the workshop. The concept that transmission is via characteristic modes was a common theme in many of the presentations. Also, the confusion an the meaning of monofilar and bifilar to describe these dominant modes was cleared up. But, there was still a healthy divergence of opinion on what constitutes an optimum system. It was generally agreed that further analytical and experimental work is definitely needed. In particular, it was stressed that independent measurements of the constitutive properties of the electromagnetic environment are needed. Also, there was considerable concern that laboratory measurements of rock samples could lead to misleading results for the effective conductivities. Also, there was a general recognition that over simplified propagation theory should not be used to interpret field data. From a theoratical and practical point of view, it was realized that mode coupling plays a vital role in the transmission channel. One must not only understand which and how many propagation modes are excited by the transmitting antenna, but the conversion of energy from one mode type to another must be accounted for. This conversion can either be done intentionally (by fixed mode convertors) or non intentionally (by random wall roughness). In fact, mode conversion can be quite complicated when various propagation paths exist such as when insulated cables, leaky feeders, grounded rails, coal seams, etc. all convey portions of the electromagnetic energy. However, this state of affairs should be regared as an. opportunity for extended communication coverage in mines rather than a limitation of a desig. procedure based on preconceived notions of the dominant propagation mechanism.

Jan 1, 1978

By J. H. Keeler

The tensile characteristics of Zr-Fe binary alloys containing up to 5 atomic pet Fe are reported for the temperature range —195o to 500°C. A linear relation between stress at constant strain and volume fraction ZrFe2 was found. The coincidence of data from unalloyed zirconium with zero volume fraction ZrFe2 indicated little or no solid solution in IL-zirconium, in agreement with Hayes, Roberson, and O'Brien.' The absolute increase in strength due to particle strengthening, although decreasing with increasing temperature, was a greater percentage at high temperature. ZIRCONIUM is of interest for use in nuclear reactors because of its low neutron absorption, good corrosion resistance, and high melting temperature. The alloying of zirconium with iron has been considered as a means of increasing the mechanical strength of zirconium without seriously increasing the neutron absorption " over that of unalloyed zirconium. The Zr-Fe system has a eutectic at 934°C and 23.7 atomic pet Fe and a eutectoid at 800°C and 4.0 atomic pet Fe. The zirconium-rich end of this system determined by Hayes, Roberson, and O'Brien' is shown in Fig. 1. The intermetallic phase coexisting with a and ß-zirconium has been reported as Zr2Fe3,1 with a,, - 7.04A, and as ZrFe2,2 face-centered-cubic, the phase being of the MgCu, type (C-15). It was more recently agreed to be ZrFe33 and face-centered-cubic. This intermetallic phase is essentially insoluble in a-zirconium, the hexagonal-close-packed modification; and the lack of solubility makes the system particularly interesting metallurgically. The system is strengthened almost exclusively by particles of in-termetallic phase, and there is very little solid solution strengthening to complicate the analysis. The Bureau of Mines, in its survey of zirconium-base alloys,' reported the tensile properties of Zr-Fe alloys made from chloride process zirconium, induction melted in graphite crucibles, and swaged at 850°C in iron sheaths. Additional data on these ZrFe alloys were given by Hayes, Roberson, and O'Brien.' Chubb and Muehlenkamp% have recently reported the strength of Zr-Fe alloys containing up to about 1.25 atomic pet Fe. These alloys were made from crystal bar zirconium, hot worked at 820°C, annealed at 700°C, and tested both at room temperature and at 316°C. Experimental Procedure The materials used in this investigation were high purity zirconium made by the iodide process and electrolytic iron. The composition of the zirconium as obtained by spectrographic analysis and the nominal composition of the iron are given in Table I. Alloy ingots weighing 100 g were made by are-melting under argon in water-cooled copper crucibles in a multihearth furnace."

Jan 1, 1957

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By R. I. Jaffee, R. M. Evans

IN recent years, the interest in liquid metals as heat-transfer media for power plants has been very great. The possibility of the development of nuclear power plants has increased this interest and served as the impetus behind much research on low melting metals and alloys for such purposes. The principal reasons for consideration of liquid metals as heat-transfer media lie in their high thermal conductivity and consequent high heat-transfer coefficients, stability at high temperatures, and the high ranges of temperature possible. The element gallium possesses some of the requisite properties for a heat-transfer liquid. It is a unique material, having a low melting point and a high boiling point. Pure gallium melts at 29.78oC, and suitable alloying will produce a metal which melts below room temperature. The boiling point is about 2000°C. As it is a liquid metal, the heat-transfer characteristics would be good. Gallium is not now readily available, due in part to a lack of uses for the metal. Nevertheless, it is not a rare element, and a sufficient supply of gallium exists to permit its consideration for this use. Since gallium has some promise as a heat-transfer liquid, owing to its unique properties, research on the subject was carried on at Battelle Memorial Institute at the request of the Bureau of Ships, U.S.N. The research had as its objectives the determination of the effect of alloying on the melting point of gallium, and the study of the corrosion of possible container materials. In this research, alloys were found which had significantly lower melting points than pure gallium, but none which simultaneously fulfilled other additional requirements, chiefly the corrosion problem. Neither was it found possible to reduce the melting point of certain otherwise suitable alloys appreciably by small additions of gallium or gallium alloys. The results gave little hope that gallium alloys can be developed which enhance the good properties and minimize the undesirable characteristics of elemental gallium. Thus, gallium now appears less promising than other metallic heat-transfer media. The experimental thermal-analysis techniques used in this work have been described.' Experimental Results As a first approximation, the development of low melting gallium alloys was based on alloying elements suitable for use in a nuclear power plant, which also lowered the melting point of gallium. Information from the literature, summarized in Table I, indicates that. tin, aluminum, and zinc are the only suitable elements which cause a lowering of the melting point of gallium. Indium and silver also lower the melting point of gallium, but are of little interest for use in nuclear power plants. Of the elements reported not to lower the melting point of gallium, there is some ambiguity on the behavior of copper. Weibke3 obtained solidus arrest temperatures of 29°C for Cu-Ga alloys from 60 to 90 pct Ga, 0.8C lower than the generally accepted melting point. This may be the effect of a eutectic close to gallium, or, more likely, the result of impurities, or experimental error. The seven elements listed in Table I whose effects were not known were of potential interest if they lowered the melting point of gallium. Their effects were determined experimentally for this reason. Binary alloys containing nominally 2 pct of each of these elements were prepared in the form of 2-g melts by placing the components in a graphite crucible and holding them in an argon atmosphere at 370°C for 5 hr. These melts were then subjected to thermal analysis. In all cases. the solidus temperature was the melting point of gallium. Since these elements (As, Ca, Ce, Mg. Sb, Si, and T1) did not lower the melting point of gallium, they were not considered further as components of a eutectic-type alloy. Ga-Sn-Zn Alloys Preliminary considerations of this system for low-melting alloys were encouraging. All three binary systems were of the simple eutectic type. The composition and melting points of the eutectics were as follows: Sn-9 pct Zn (199°C), Ga-8 pct Sn (20°C), and Ga-5 pct Zn (25°C). Therefore, the probability of a ternary eutectic was high. For reasons to be discussed later, aluminum could not be used as an alloying constituent, leaving the Ga-Sn-Zn system as the only one of interest for low-melting gallium-

Jan 1, 1953

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine&apos;s operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983

By H. Miller

In recognition of the need for a portable low-profile hard rock crusher, the Bureau of Mines sponsored the development of such a unit capable of moving up as the face advances. By allowing primary ore reduction at or near the mine face, the advantages of conveyor haulage From the face as demonstrated in soft ore and coal mines, could be realized for hard rock Brines as well. This report presents the results of a development and testing program for such a portable low-profile crusher, designed by Eagle Crusher Company and called the M44. The unit has an extremely low vertical profile considering its size and capacity. The crushing jaws, which form the crushing lumber, are inclined, with the lower jaw mounted for eccentric movement relative to the stationary upper jaw. This provides efficient crushing while also forcing material through the crushing chamber. As a result, the inlet feeder can be disposed horizontally. To facilitate correct processing of different materials, the size of the discharge opening and the action of the movable crushing jaw are variable. The unit also incorporates a feeder hopper and discharge conveyor that provides for efficient ore handling through the machine. Tests demonstrated the M44 Crusher&apos;s high capacity, efficiency and reliability. During testing, it crushed over 120,000 tons of materials of up to 32,000 psi compressive strength at production rates in the 200-350 tons/hour range. The unit operated smoothly under simulated low-headroom conditions, and Proved readily transportable.

Jan 1, 1983

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

By D A. Edmunds

The most important development that has been taking place recently relating to mining operations in New Zealand would generally be regarded as being the Resource Management Law Reform. This has been widely publicised by the Government as a comprehensive review of the laws governing New Zealand&apos;s natural and physical resources. Submissions have been sought and a free phone provided to encourage public participation. Recently a Discussion Paper has been prepared by the Core Group coordinating the review to explain progress on Phase One (Ministry for the Environment, Directions for Change: A Discussion Paper, Wellington 1988). It outlines Government decisions already taken which impinge on the Review and describes the possible models for resource management laws. However, it is possible that some fundamental practical issues of significance to the mining industry will not be addressed and may be lost sight of in the much wider issues which are to be covered. The purpose of our paper is to address one of these issues namely, the interrelationship between any new resource management legislation and the Conservation Act 1987 (as recently amended) in the context of Ministerial consents. The importance of this issue can be seen from the fact that as at 7 June 1988 there were 279 mining licence applications and 223 prospecting licence applications waiting to be determined by the Minister of Conservation. Since April 1987 only 19 mining and 13 prospecting licences have been consented to. In addition a major proportion of New Zealand&apos;s mineral resources are contained with land administered by the Department.

Jan 1, 1988

By S. S. Hsieh

As part of a program to address the long-term need to ensure adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial deoiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble that contained about 23% P2O5 and 2.0% MgO. The P205 recovery was 80.8-86.5%.

Jan 1, 1991

By P D. Katsabanis

The dynamic tensile strength of geomaterials is known to be highly dependent on the strain rate of the load applied. This is significant in applications where the material is subjected to shock waves and impact loading. This paper proposes the use of a simplified method to determine the dynamic tensile strength of hard brittle rocks using an explosively impacted version of the Hopkinson Pressure Bar. A compressive stress wave was propagated in a sample, representative of the material of interest, by detonating a small charge at one end of a cylindrical sample. The tension wave, generated upon reflection at the free face, causes spalling in brittle materials. Strains at four points in the specimen were continuously measured and the dynamic tensile strength was determined by applying the one-dimensional wave theory.

Jan 1, 2010