Search Documents

Significantly increase the amount of fresh air that sweeps the face in front of a continuous mining ma-chine, in order to prevent methane gas buildup. Approach Water sprays are mounted along the sides of a continuous miner and behind the cutter head to help push ventilating air along the required path, and prevent its short circuiting. How It Works A continuous miner is fitted with two sets of water sprays, one of which is used at a time. The set of sprays shown in the diagram, helps move the ventilating air forward along the left side of the miner and across the cutter drum from left to right. That air is then drawn into the exhaust air passageway located along

Jan 1, 1978

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Joseph Daniels

[Adequate supplies of suitable coal and coke are prime requisites in many industries, particularly those dealing with the utilization of mineral resources, recently interest has been focused on the possibilities of using electricity produced at Bonneville and Grand Coulee, Wash., in many electrochemical and electrometallurgical processes, in which core or some form of carbon is necessary in addition, discussion has been revived on the possibility of making iron and steel by the conventional methods employed in blast and open-hearth furnaces. The subject also is important at this time because of its relationship to industrial preparedness for national defense. A supply of coke from local sources on the Pacific coast is necessary in any program of production for strategic sufficiency of certain materials. An anal trio involving tae establishment of such industries should include detailed data on available supplies of coal, the quality and properties of the coke produced, and the technologic and economic factors involved in manufacture of echo and disposal of byproducts.]

Jan 1, 1941

By Arnis Mangolds

A study of the technical and economic feasibility of using a unique undercut and fill system developed by USBM engineers to mine steeply pitching coal is discussed. A brief resource assessment has indicated that significant reserves exist in most coal regions to justify the development of a safe and economical method of extracting steeply pitching coal. The undercut and fill system combines hydraulic coal cutting with unassisted gravity fluming of the coal slurry. Mining occurs across strike and the extended entry is backfilled to provide uniform strata control and an impermeable water and air barrier. Subsequent mining occurs beneath the previously filled stope such that the roof consists of a solid, controlled back. In addition to providing positive roof and hanging-wall support, the backfill system eliminates subsidence potential, post-mining drainage, and the danger of spontaneous combustion from naturally drafting air currents. A unique through-flowing ventilation system permits passage of return air through the production face via ducting located at the backfill-coal junction. This provides a constant supply of fresh air at the face, eliminates the need for brattice cloths, and provides an additional escapeway for the miners. The preliminary estimates indicate a production rate in the neighborhood of 31.9 tons/ manshift. Capital costs are approximately $3.17/raw ton over a 20-year life with an initial investment per annual ton of $48.29. Total cash-costs for labor, supplies, power and benefits range in the vicinity of $19.59 for a 704,460 ton/year mine, or a total cost of $22.76/ton. These costs do not include federal and local taxes or post-of-money; however, the cost of coal is well within the area selling price.

Jan 1, 1981

By Michael C. Horn

The 61,470-acre Lick Creek Roadless Study Area is in the western Salmon River Mountains, centered 12 miles northeast from McCall, ID. U.S. Bureau of Mines personnel examined the roadless area in 1984. There is no recorded mineral production from the study area and no current mineral-related activity was observed. The roadless area is underlain by granitic rocks of the Idaho batholith. Pegmatite dikes and aplite dikes are present locally. Sampling indicates these rocks are not mineralized. No mineral resources were identified. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of federal lands recommended for wilderness, as required by The Wilderness Act of 1964. The USBM examines and evaluates individual mines, claims, prospects, and mineralized zones; USGS conducts broader geological, geochemical, and geophysical surveys. Such data helps Congress and other federal agencies make decisions affecting the use of public lands.

Jan 1, 1986

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By T. C. Rao, Vanangamudi. M., J. P. Barnwal

Experiments were carried out on 76 mm laboratory heavy medium cyclone treating -2.0 t 0.5 mm coal and on two 600 mm industrial heavy medium cyclones treating coal in the size range -13.0 t 0.5 mm. The variables studied were spigot diameter and feed medium gravity. The generalised distribution curve for the separation of coal in these heavy medium cyclones has been defined by the equation [ ] The specific gravity of separation SG has been found to increase linearly with increase in feed medium, gravity (SGf). The relationship for SG of industrial cyclone is given as 50 SG = -6.801 t 6.463 SGf t 0.0327 Spig 50 -0.02625 SGf. Spig. Further, the probable error for the separation has been found to be linearly related to (SG50 - SGf ) according to the equation [ ] The model equations developed have been used to select appropriate levels of operating conditions to achieve an increase in the yield by about 2 to 4% without affecting the quality of the product.

Jan 1, 1990

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By Maurice Deul

This bulletin summarizes the work conducted under the Bureau of Mines methane control research program during the years 1964 to 1979. This research effort was directed toward improving existing methods and developing alternative methods of reducing the explosion hazard during mining. The research was performed in three general areas: (1) basic factors that control the emission of methane into coal mines, (2) methane control during mining, and (3) methane drainage in advance of mining. Topics discussed in this bulletin include the magnitude of the methane problem; the equipment and instruments developed; the geological, chemical and physical parameters that control the movement of methane in coalbeds; the direct method of determining gas content; the estimates of gas content from adsorption data; and methane drainage, through shafts, through horizontal boreholes, through vertical boreholes, or through slant holes. Improvements in ventilation, control of methane in gob areas, and water infusion are also discussed, as is the potential use of coalbed methane as a supplement to natural gas supplies. This bulletin provides a comprehensive source of information on the accomplishments of the Bureau's methane control research program, on the technology developed, and on the direction of further research.

Jan 1, 1986

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

By Betty L. Gibbs

Geologically simple deposits can be modeled quickly and easily with inexpensive gridding and mapping software. Hundreds of mines around the world use RockWorks99 and Surfer 7 for generating contour maps, producing log plots and cross sections, and performing other useful geological calculations. These programs are used by many mining operations as their only modeling and graphical software or they are used in conjunction with larger systems. The investment in learning time is low and the programs produce reasonable quality results with standard computing equipment. RockWorks99 and Surfer 7 provide a good level of capability while maintaining high quality technical integrity. Both programs are used for many applications in mining, oil and gas, environmental and other fields that require analysis of spatial data.

Jan 1, 2000

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By R. Barthel, O. Nitzsche, J. Pateiro Fernández, T. Cramer

The Hong Gai coal field in northeast Vietnam has been the main coal mining area of Vietnam for more than 150 years. Anthracite coal is produced from several open pit and underground mines situated close to the UNESCO world natural heritage site Ha Long Bay. The mining-induced environmental impacts such as dust emissions, acid mine drainage, and visual impairments due to waste dumps resulted in severe conflicts of interests regarding future land use and the protection of the world natural heritage site Ha Long Bay. Within the RAME project (Research Association Mining and Environment in Vietnam), Brenk Systemplanung is contributing to an improved environmental and sustainable planning in Vietnam's mining industry and the reduction of environmental impacts on Ha Long Bay by developing suitable and sustainable technology and planning measures (e.g. for dump construction/rehabilitation, predictive modelling, and/or monitoring) for Vietnam's leading coal producer.

Jan 1, 2011

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By M. K. Elmouttie, G. V. Poropat

Mapping of exposed rock walls provides data on geological features such as joints, bedding planes, faults etc critical to the economics and the safety of mine operations. Traditional, manual methods of mapping can be time consuming, error prone and limited in their coverage. New methods have been developed to map exposed faces remotely and safely however the benefits of these methods are only fully realised when exposed structures can be quickly and easily mapped using automated methods. This paper describes the application of an automated method of analysis of 3D images that provides users with the capacity to map exposed structures automatically. The method is based on the use of vector classification methods used in some neural network systems and provides rapid and reliable identification of exposed planes. CSIRO Exploration and Mining is applying these methods to 3D images for a range of applications from pit mapping to machine automation.

Jan 1, 2006

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983