Search Documents

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By W. J. Boone

The Bureau of Mines has programmed for publication a series of Reports of Investigations of studies it has undertaken on low-temperature phase equilibria of several helium-bearing natural gases. This report is the second of a series of papers of the same general title; it is anticipated that additional reports of this series will be published. The advent of a helium conservation program and the prospect of production of helium by private industry, make it especially desirable to publish these data. This report describes phase equilibria related to a natural gas that is processed for helium at the Bureau's Exell Helium Plant (located about 35 miles north of Amarillo, Tex.). Carbon dioxide and water in the gas were removed before making the study; hence the data obtained are representative of the gas stream immediately after similar preliminary treatment in the plant process. Phase equilibrium data were obtained for conditions from -50° to -275° F. and from 100 to 500 p.s.i.a. Analyses of samples were made as follows: For a given run at a selected temperature and pressure, samples of the vapor and liquid phases were analyzed by mass spectrometer, and an additional sample of the liquid phase was analyzed for helium by means of special apparatus (7). 4

Jan 1, 1962

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By H. Naghavi, M. Karimi

"In self-aerated flotation machines, the gas rate depends on operational variables (e.g. froth depth and impeller speed), pulp properties (e.g. solid content and viscosity), and reagent addition (e.g. type and concentration of frother). The gas rate has a strong correlation with the flotation performance by influencing the gas dispersion properties and froth retention time. A factorial experimental design was used to study how the gas dispersion properties, the froth retention time, and the flotation performance respond to changes in froth depth and impeller speed (as the most common operational variables). An in-depth understanding of the effects of impeller speed and froth depth on the gas dispersion properties, especially the bubble surface area flux and froth retention time, is necessary to improve operating strategies for self-aerated flotation machines. All experiments were carried out in a 50 m3 selfaerated flotation cell in an iron ore processing plant. The results showed that the froth depth affected the metallurgical performance mostly via changing the froth retention time. The impeller speed had two important impacts on the metallurgical performance via varying both the froth retention time and the bubble surface area flux in the froth and pulp zones, respectively. The interaction effects of the froth depth and impeller speed were also established. This allowed us to develop a strategy for operating selfaerated flotation machines based on varying the froth depth and impeller speed with regard to the cell duty. IntroductionA mechanical flotation machine may be divided into two distinct zones. namely the pulp zone and the froth zone (Goodall and O’Connor, 1989; Yianatos, Bergh, and Cortes, 1998; Rahman, Ata, and Jameson, 2015a, 2015b). The overall flotation recovery, Ro, including the true flotation (particles attached to the bubble lamellae) and entrainment (particles recovered in water held in the bubble plateau boundaries), is a function of the recoveries in the two zones. It is calculated as follows (Dobby, 1984):"

Jul 1, 2019

By Parviz F. Rad

The Bureau of Mines used a linear cutting apparatus equipped with a 7-inch disk cutter to cut grooves in marble, limestone, granite, and quartzite under a normal force of 7,000 lb. The size distribution of the muck for various grooves was determined through sieve analysis. A statistical search showed that Weibull distribution describes the size distribution better than other available functions. Results indicate that fineness modulus, chip population, and dimension of the largest chip can be used as indicators of cutting efficiency. The results correlate with those obtained from the boring machines and other lab experiments. Application of the principles established through this work to the operation of boring machines is explained

Jan 1, 1974

By Natália Cristina Candian Lobato

Questões como a variação no preço dos minérios, a escassez dos minérios de qualidade e a preocupação contínua com a sustentabilidade faz com que a indústria busque matérias-primas alternativas, o que estimula o uso dos resíduos. Dentro da siderurgia, muitos resíduos gerados possuem elevados teores de metais, logo podem retornar ao ciclo produtivo após passar por tratamentos adequados, acarretando, assim, em economia ao processo. A carepa é um resíduo composto de mais de 60% de ferro. Devido à esta característica já é parcialmente reaproveitada pela siderurgia, porém a presença eventual de óleos em sua composição ainda faz com que parte desse resíduo seja destinada a aterros industriais. A carepa também pode ser empregada como matéria-prima em outros processos industriais. Assim, o intuito deste trabalho é apresentar rotas de reaproveitamento da carepa siderúrgica.

Aug 16, 2017

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By Doss H. White

The value of non fuel mineral production in Alabama in 1991 was $539.9 million, a decrease of $20.7 million, a result of the nationwide recession that was felt throughout the State's economy. The 3.7% decline in mineral sales was due primarily to a slowdown in construction, which had a major impact in the construction minerals mined instate. Production and sales of crushed stone and sand and gravel fell significantly below the value reported in 1990. Despite the recession, Alabama moved from 21st to 20th place nationally in mineral value. Mineral industry developments in 1991 were primarily in the metals manufacturing sector. Reynolds Metals Co., Sheffield, celebrated 50 years of operation in Alabama. During the November celebration, the company dedicated a $121 million expansion that included a new casting facility and sheet rolling operation. Gulf States Steel Corp., Gadsden, completed the first full year of operation of its new multimillion-dollar continuous caster.3 The Foundry of the Shoals Inc., Florence, replaced two coke-fired furnaces with electric furnaces.

Jan 1, 1993

Effect of Iron on ash fusion temperature and waterwall deposits FeS, H2S on tube material corrosion and erosion [ ]

Jan 1, 2005

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

"In mineral exploration and mining applications, it is sometimes necessary to reduce sampling error in order to improve representivity of individual sample assays. Historic efforts to reduce sampling error have relied on the belief that larger samples exhibit less sampling error. Justifications for this belief traditionally have coupled the binomial theorem with an ideal geological material consisting of ore and gangue particles of equal size and shape (an equant grain model) and empirical tests of geological materials, to illustrate an inverse relationship between sample size and sampling variance. To date, no proof exists of this sample size-sampling variance relationship in real geological materials exhibiting variations in grain size, shape, composition, and degree of liberation.Using first principles calculus and the formula for the mean, sample mass and sampling variance are proven to be inversely proportional in all geological materials. Distribution assumptions and physically ideal geological models are not used in this proof. Furthermore, algebraic manipulations of expressions describing the variances of equant grain models consistent with binomial, hypergeometric, and Poisson distributions reveal that these models also exhibit an inverse sample size-sampling variance relationship. Thus, the sampling behaviors of these models are numerically consistent with the sampling behaviors of real geological materials, and these models can be used to estimate sampling errors in real geological materials using simple sampling parameters."

Jan 1, 2007

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

By A. W. Diedericks

Rosh Pinah Zinc Corporation (RPZC) identified implementing a Mineral Resource Management (MRM) programme at the mine as a strategic incentive. The purpose of the programme is to optimize the economic value of the RPZC mineral resource, over the total value chain of the mine, taking expected macro economic conditions into consideration as well. With Mineral Resource Management still being a relatively young drive in the mining industry, information on the concept is relatively scarce. RPZC had several successes and problems with implementing such a concept and also still has a way to go before a complete Minerals Resource Management approach is implemented at the mine and entrenched as a working culture. The purpose of this paper is to: ?define a systems approach to implementing a Mineral Resource Management programme at a base metal mine ?indicate the specific MRM approaches taken at RPZC ?indicate the expected advantages of implementing a MRM approach ?measure the actions already taken against the systematic MRM approach, and indicate the advantages already captured ?indicate the way forward taking lessons learned into consideration ?indicate proposals to implement the MRM approach in the macro mining environment in South Africa.

Jan 1, 2003

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002