Search Documents

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By R. E. Rick-Secker, W. M. Baldwin, R. McC. Baker

The development of residual stress in strip during rolling has not been systematically studied. A few scattered papers1 -3 mention the existence of residual stresses in rolled strip or touch upon some of their consequences,4 but there is no report of experimental studies in the literature describing the effect of roll diameter, strip thickness, reduction per pass, metal or metal temper on the magnitude of residual stresses developed in strip. A knowledge of the effect of these factors is of utmost importance since the present trend in some mills to roll thicker castings brings the rolling operation directly into that set of conditions which, as will be brought out in the present paper, can develop residual stresses of a high order of magnitude. Fundamentally, residual stresses are developed when a metal is inhomogeneously unloaded from a plastic stress state. A quantitative treatment of the problem requires a reasonably complete understanding of both the plastic stress state existing in the metal during deformation and the elastic stress state that would exist in the metal if the metal deformed as a perfectly elastic body. Our knowledge of either state during rolling is so meager that we can make no more than certain limited predictions. The external stress state* operating between the roll and the metal consists of Fig i—External stress state operating on metal being rolled (after siebel and LUEG5) compressive stresses acting almost perpendicularly to the strip surface but varying in intensity both across the width of the strip and along the length of contact between the roll and the strip. An example of such a stress distribution is shown in Fig I. The nature of the internal stress state, produced by this distribution, is not known. Various investigators,5-7 however, have felt that a qualitative similarity must exist between the internal stress state so produced and that produced in a wide strip that is compressed between two flat-nosed punches. In the latter case the external stress state is represented by a uniformly distributed compressive stress acting per-pendicularly over the face of the tool. The

Jan 1, 1949

By Peter Hatherly

As a discipline, geophysics covers an enormous range of scales and applications - from planetary geophysics through to the monitoring of acoustic emissions of rock samples. Although it is not a core discipline within the mining industry, geophysics has a useful role in providing information on the nature of the rock mass and the way it is responding to the mining process. For coal mining purposes, geophysical studies mainly seek to - delineate boundaries between the coal and the various layers within the surrounding strata - determine the physical properties of the rocks in-si tu, and - monitor the response of the rocks to the mining process Some of these applications may be associated primarily with mine planning, but once a mine is underway, most geophysical results can be used for the purposes of ground control. For example, insights into the nature of a geological fault mapped by a 3D seismic reflection survey will be relevant to determining support requirements while mining through it. In some instances there are parallels in the use of geophysics by the petroleum industry. Seismic reflection and wireline logging techniques have mainly been developed for petroleum exploration where their on-going development continues to provide spin-offs for the coal industry. The 3D seismic survey techniques that we now routinely employ were in their infancy 25 years ago and, almost certainly, the high quality borehole scanning tools that are now available would not have been developed without the need for petroleum well evaluation. Mining has also led to the development of specific techniques. An example is microseismic monitoring for the management of roof conditions during longwalling, and also the prediction of rock and coal bursts. The use and success of this technique have grown greatly over recent years. Another example lies with the use of geophysical wireline logs to predict rock strength and in rock mass classification. Coal seams also provide an unusual geophysical situation in that they form seismic and electromagnetic waveguides. The in-seam seismic and radio imaging methods have been developed to exploit these geological properties. In this paper I address the development and application of geophysical methods such as these with a particular emphasis on their role in ground control. We will see that there have been many developments over the past 25 years but we should also think about the future and how geophysics needs to be developed. From a miner?s perspective, one obvious area of need is in the detection of voids in the vicinity of current mine workings, be they old workings or karsts within nearby carbonate beds.

Jan 1, 2006

The Mineralogy and Reactivity of Pyrrhotite from Selected Nickel Ore Deposits and its Effect on Flotation Performance

Sep 13, 2010

By W. C. Hagel, H. J. Beattle

DURING an earlier examination of high-temperature alloy, A-286, the presence of an unknown intermetallic compound was verified by X-ray diffraction. Owing to its prominent appearance at grain boundaries, the arbitrary name of G phase was assigned.' Low-silicon, vacuum-melted heats were found to contain no G phase, and this investigation was initiated to determine the influence of silicon on G-phase formation; additional work was undertaken to extend existing data on other intermetallic compounds and the aging reactions in this group of alloys. Taylor and Floyd2-4 observed that the Ni3Al phase (y') and the Ni8Ti phase (7)) are the only equilibrium intermetailic compounds in nickel ternary alloys containing up to 25 pct Cr and 10 pct Ti or Al. They found that y' can dissolve considerable nickel, chromium, and titanium, although the stoichio-metric composition of 7 remains fixed. Nordheim and Grant5 confirmed that age hardening of 80 pct Ni-20 pct Cr alloys of the Nimonic-80 type is due to precipitation of y', where aluminum is partially replaced by titanium. They suggest that optimum hardness and ductility result from increasing the titanium to aluminum ratio toward the end of the y' solubility range and from increasing total titanium and aluminum content to the maximum limit permitted by processing. Such information is necessary for those seeking to improve the service-temperature range and long-time structural stability of high-temperature components. Experimental Methods Compositions of materiais studied. are listed in Table I. Alloys D, E, and F possess representative A-286 analyses; silicon increases from less than 0.02 to 1.75 pct in alloys A to H; in alloys I to K, titanium decreases from 2.24 to 0.39 pct, and aluminum increases from 0.1 6 to 240 pct. Alloys A and D were solution heat treated for 4 hr at 1700°F, oil quenched and aged for 0.5, 2, 6, 12, 30, 70, 200, and 1000 hr at 1200°, 1300°, 1400°, and 1500°F. Therefore, a total of 33 specimens was required for each

Jan 1, 1958

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 krn NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity. The deposit is mostly overlain by younger Proterozoic sediments and later Cambrian age limestone cover and only a small proportion of the mineralisation crops out. Mineralisation has a subtle surface expression without a classic gossan profile, probably due to the low iron sulphide content of the ore. These factors contributed materially to the length of time between the first recognition of lead-zinc-silver mineralisation in the area by prospectors in the 1880s, to the discovery of the orebody by CRA Exploration Pty Ltd (CRAE) in April 1990.   Small scale prospecting and mining continued in the area from the date of the first mining lease in 1887. Post 1950, the deposit area was also included within nine separate regional exploration titles prior to CRAE's title acquisition in 1987. CRAE's original exploration strategy was partly pragmatically and partly conceptually inspired, but the eventual discovery only partly conformed to the original conceptual model. The deposit was found higher in the stratigraphy than the original target position, with unexpectedly low total sulphide content relative to other known deposits.   The discovery soil anomaly was located by the CRAE's first regional orientation traverse line in the area, but was not drill tested for three years. The discovery sequence at Century has strong elements of persistence, technical competence and some luck. It demonstrates that even in well explored terrains (by conventional standards) the exploration story can never be said to be over. The foreshadowed development of an economic resource at Century will hopefully inspire continued commitment to 'brownfields' exploration by mining companies, and demonstrate to external regulators the importance of genuine multiple land use strategies and the need for continued access to land for exploration and mining purposes.

Jan 1, 1995

By Ludwig Hermann

"Phosphorus is required by every cell of living organisms and essential for plant growth. It is a non-renewable resource that must be mined from natural deposits, going gradually into depletion. Abundant secondary resources are available in sewage sludge and meat and bone meal, with the highest exploitable P concentrations in ashes that remain from their widely used combustion with energy recovery. ASH DEC has successfully removed heavy metals and transformed sewage sludge ash into a marketable P fertilizer by application of a thermo-chemical treatment process. Pilot scale investigations in which ash was treated proved that generally heavy metal limits required by fertilizer legislation can be attained. To achieve a high P availability for crops – an essential fertilizer quality feature – was a more challenging R&D task. Our presentation demonstrates the scientific approach and R&D results that lead from assessment of market requirements to licensed products.IntroductionPhosphorus (P) is required by every cell of living organisms. It is one of the major elements for plant nutrition and therefore essential for crop production. P supply in plant nutrition depends entirely on external inputs into soils [1]. This is achieved by P-fertilizers deriving from rock phosphate deposits that are gradually going into depletion. Serious prognoses anticipate that rock phosphate will be the first low running resource in the world [2]. In the EU, last year 2.530 kt of phosphorus (P2O5 in fertilizers) was consumed and only 313 kt (P2O5 in rock phosphate) was mined. Since 2007, rock phosphate prices have increased by 500% because of a tight supply situation [3].For these reasons, P recycling is becoming an increasingly important issue. Suitable secondary raw materials with regard to their high P-content and abundance are sewage sludge and meat and bone meal. In the EU 989 kt P2O5 are accumulated annually in theses materials, of which 632 kt P2O5 are permanently lost to landfills and other forms of disposal. The main reasons for their limited recycling are concerns on heavy metal contents and organic pollutants that may incite health hazards. As an additional shortcoming, the availability of P from these materials to plants is poor and storage and transportation are problematic issues [4, 5]."

Jan 1, 2008

By Reno M. Pappas, Christopher Mark

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a lab- oratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship, was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 1993

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By C. Özgen Karacan

Gob gas ventholes (GGV) are used to control methane inflows into a longwall operation by capturing it within the overlying fractured strata before it enters the work environment. Thus, it is important to understand the effects of various factors, such as drilling parameters, location of borehole, applied vacuum by exhausters and mining/panel parameters in order to be able to evaluate the performance of GGVs and to predict their effectiveness in controlling methane emissions. However, a practical model for this purpose currently does not exist. In this paper, we analyzed the total gas flow rates and methane percentages from 10 GGVs located on three adjacent panels operated in Pittsburgh coalbed in Southwestern Pennsylvania section of Northern Appalachian basin. The ventholes were drilled from different surface elevations and were located at varying distances from the start-up ends of the panels and from the tailgate entries. Exhauster pressures, casing diameters, location of longwall face and mining rates and production data were also recorded. These data were incorporated into a multilayer-perceptron (MLP) type artificial neural network (ANN) to model venthole production. The results showed that the two-hidden layer model predicted total production and the methane content of the GGVs with more than 90% accuracy. The ANN model was further used to conduct sensitivity analyses about the mean of the input variables to determine the effect of each input variable on the predicted production performance of GGVs.

Jan 1, 2009

By Antonio Fabiano de Oliveira

Estudos de laminação com revestimento de cromo e influência nas propriedades foram realizados com o objetivo de aumentar a produtividade dos cilindros. Para tal, foram utilizados cilindros cromados para laminação de chapas de cobre, com amostragem da técnica de réplica epoxy. A compreensão da correlação entre microestrutura e propriedades do material é objeto de grande interesse e, ao mesmo tempo, necessário para aplicação prática na laminação a frio, combinando revestimento e produtividade. O objetivo da pesquisa atual é comparar as propriedades tribológicas do cobre antes e depois da laminação, no cilindro de trabalho e chapa, com e sem revestimento de cromo.

Oct 30, 2017

By J. Madias, E. Benavidez, E. Brandaleze, L. Castella

Knowledge of the physical and chemical properties as well as the behaviour of the mould fluxes during melting, important in order to improve continuous casting operations. Lubrication and control of heat transfer in the mould are the more relevant functions of these materials. Values of physical properties like viscosity and surface tension at melting range temperatures are required, as much as the thermal behaviour under process conditions. The heat extraction from the liquid steel has an important effect in the final quality of products. Mould fluxes are constituted by different oxides, and may form glasses and crystal phases during cooling. The solidification rate and the chemical composition determine the proportion, type and crystalline morphology, which are responsible of the thermal transfer processes. In this paper, viscosity values are reported in the melting range temperatures calculated by means of the Riboud model and compared with fluidity results obtained by the inclined plane technique. Also the linear expansion of the mould fluxes at high temperatures was determined by dilatometry. The crystallization in two different fluxes was determined by DTA tests and correlated with the basicity index. Crystal phases were evaluated by scanning electronic microscopy on quenched samples at 1300°C. This information is relevant to increase the knowledge on the peritectic steel grades casting process in order to improve its quality. Keywords: mould fluxes, heat transfer, crystal phases, peritectic steels, thermal properties.

Jan 1, 2004

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

Hydraulic fluid power systems are advantageous whenever power output must be accurately and safely controlled. The load movers, cylinders, jacks, rotary actuators and hydraulic actuators in these systems can be made to smoothly and accurately start, stop, reverse, hold position or move steadily under heavy and variable loads or torques. Because hydraulic systems are simple, compact, reliable, and low cost compared to other power methods and because they can deliver controlled power anywhere on the machine to which a hose can be routed, they are a pan of almost every type of machine found on a coal mining section. Some of the functions they perform are positioning drill booms, driving drill pots on roof bolters, positioning curter booms, raising, lowering, and swinging conveyors, driving conveyors on continuous miners, raising, lowering, and applying sustained loads to longwall roof supports, and advancing the face conveyor and roof supports in longwall mining operations.

Jan 1, 1982

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972