Search Documents

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts, The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10-7 atm. The concentration of CU2+ in such slags becomes significant at oxygen potentials of greater than 10-7 atm at 1300 °C. The activities of CuO0.5 and AsO1.5 in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of SiO2 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2x 103 cm2/s at 1350 °C and activation energy of 16 kcal/mol. Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300°C. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material,

Jan 1, 2003

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By Geoffrey A. Brooks, M Akbar Rhamdhani, Md Saiful Islam

A novel electrically-enhanced metal purification using slag has been developed. This was achieved by applying DC potential between liquid metal and slag phases. The concept was demonstrated through small-scale experiments at temperatures of 1500-1600oC for the removal of boron from Si-B melt using CaO-SiO2-16wt%Al2O3. Silicon (containing B) and slag were reacted in an alumina crucible in a resistance tube furnace. A circuit was produced by immersing graphite rods into the silicon bath and the slag layer. Electrical potential differences of up to 3.5 V were applied during the reactions. The reaction rates, the opencircuit voltages and short-circuit currents (in the case when the potential was applied) were then measured and determined for various slag to silicon ratio. It has been shown from this study that both the apparent rate and the boron partition ratio were increased by a factor of approximately 1.6.

Jan 1, 2014

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb-Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb-Zn ore was traced to apH effect. In the pH range, 9.5 to 11.0 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH)2 is suggested, the Fe- + ions being derived from superficial oxidation of pyrite in the ore. IntroductionGalena and sphalerite commonly occur together. A typical procedure, using xanthate collectors, is to float the galena first, at pH - 8, followed by flotation of sphalerite after activation with copper (II) sulphate at pH - 10 (to depress pyrite).Flotation tests following this procedure in an undergraduate laboratory course with a Pb-Zn ore from Polaris failed to achieve consistent selective flotation of galena. Occasionally a considerable amount of sphalerite, even though unactivated with CUSO4, floated. This was traced to accidentally high pH. A systematic study was carried out which revealed that sphalerite floated readily in the pH range 9.5 to 11.0 without activation by CuSO4 This paper describes the results of the study and discusses a possible mechanism of this flotation of sphalerite."

Jan 1, 1987

THIS paper proposes to give a general description of the pumping and other machinery in use at the Thames Hauraki Pumping Station, situated on the Thames goldfields of the North Island, New Zealand. An idea of the general arrangement of the pumping engines and pumps can be obtained, together with a certain amount of detail, by reference to the illustrations. The history of the pump is rather interesting, and is as follows: -In 1894 the Government decided that a subsidy of £1 for £1up to an amoUllt not exceeding £25,000 be granted towards the erection of suitable machinery to exploit the Thames low levels.With a guarantee of such assistance a company was floated in London, with a capital of £300,000, to develop several properties at Thames. As the old Queen of Beauty Company had produced bullion worth £400,000 prior to closing down on account ofa breakdown to its pumping gear, their shaft was chosen as the site of the principal work. As soon as the company was floated, operations were commenced at the Queen of Beauty shaft, situated at the entrance of the Waio-Karaka Creek, and not more than about half a mile distant from the principal mines on the field.

Jan 1, 1912

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By Nobuzwe Makhotla, Sasha Boskovic, Steve Hearn

"Mineral separation efficiency in flotation depends, to an extent, on the type of frother used. Huntsman develops and manufactures unique frothers which are suited for mineral processing applications. This paper discusses the Huntsman approach to understanding the industry’s flotation frother requirements to optimise frother selection and introduce the Huntsman’s POLYFROTH® frother range. Specific case studies where the frothers are used are discussed. INTRODUCTION Froth flotation is a process of using bubbles to separate minerals based on their relative affinity for water. Bubbles are induced in the slurry through aeration. Chemistry is used to aid the flotation process and chemical reagents are added to enhance the separation process. The flotation reagents include frothers, collectors, surface modifiers and pH regulators that control physical and chemical conditions of solid, air and liquid phases, respectively. As described by Harris (1976), the key effect is that of bubble size control by way of preservation of the generated bubble size, which is attributed to the coalescence inhibition by the presence of the frother on the bubble surface. Following this, the frother must stabilize the froth phase. Frothers are also added to create optimal conditions for bubble creation and stability by decreasing the surface tension of the water. Depressants may be added, depending on the ore treated, to assist the hydrophilic particles to stay in the water phase. Clay particles may need to be dispersed to prevent them from attaching to the bubbles. Hydrophobic particles attach to the bubbles and are carried to the surface of the slurry where froth is formed. It is important for these bubbles to have the mobility to carry the mineral to the launder where the concentrate is collected. Types of Frothers There are generally three main groups of frothers used in froth flotation. Alcohol Type These frothers have a molecular structure that usually includes 5 to 8 carbon atoms in a hydrocarbon chain and their solubility in water is limited. Methyl isobutyl carbinol (MIBC) belongs to this category and is widely used in the industry. The weaker alcohol-type frothers are more selective and typically suited to finer particles. There are three sub-categories under this group: aliphatic, cyclic and aromatic alcohols."

Jan 1, 2015

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By D M. Aranha, M A. Fonseca, M Echtern

The regional syndeformational metamorphism affecting the Itabira Iron Formation (IIF) at Quadrilßtero Ferrffero (QF) was formerly discussed by Dorr (1965), who proposed that quartz grain size could monitor the metamorphism, according to James (1955), and that the formation of haematite could be the result of the synchronous metasomatic process. Herz (1979) suggested the existence of three metamorphic zones, not mentioning the haematite formation. It could be observed that the primary oxide phase in the IIF is magnetite and most of the hard haematite was derived from the metamorphic replacement of magnetite, forming micaceous or schistose haematite. Differently from most iron formations in the world, the formation of haematite deposits at QF occurred under high oxygen fugacity during metamorphism. The haematite microlaths display a strong preferred orientation, which determines the alongated shapes of the fragments. The terms foliated and unfoliated haematite have been applied by Dorr to the micaceous or schistose haematite, and to the isotropic, hydrothermally derived haematite. Under the microcope, the haematite exhibits a strong crystallographic or lattice orientation encircling the magnetite and martite porphyroclasts. The strain rate determined and defined the textural variation, size and economic importance of the deposits and the ore grade. Metamorphism at QF increases eastward and resulted in the formation of a gruneritic Fe-Mg amphibole, at the western portion, followed by a cummingtonitic amphibole at the central-western part, succeeded by the actinolite zone at the central-eastern part, and finally to the tremolite-anthophyllite zone to the east. These zones, arranged in a north-south pattern, can be followed in the pelitic units, whereas appear sericite-chlorite, kyanite-chloritoid and garnet-staurolite respectively. Carbonate geothermometry in IIF also may support the metamorphic variations. At the western zone the haematite forms small lenses within the itabirite, P-contents are slightly higher than in the remaining IIF, haematite grain size is minute, resulting in a submicaceous texture and the amount and dimension of relict magnetite within haematite is greater than in the other parts of QF. Jangada and Serra Azul deposits are examples of this zone. The central-western zone is characterised by significant haematite deposits, in considerable quantity and size, haematite grain size increased, in order to produce a micaceous texture, the P-contents and the amount of magnetite decreased. Pico do Itabirito, Cappo Xavier, Capitpo do Mato and Tamanduß correspond to the deposit type of this zone. At the eastern-central portion the amount of the hard haematite deposits decreases, increasing the soft haematite ore due to higher strain rates. However, it can be perceived that the relict magnetite almost disappeared and the haematite grain size became coarser than the haematite from the western zones. At the eastern zone, the haematite deposits exhibit typical schistose texture, the magnetite porphyroclasts are absent and the lowest P-grades in the haematitic iron formation. The haematite bodies characteristic from this zone are Andrade, Morro Agudo and the deposits at the Itabira District. The hydrothermally derived compact and isotropic haematite deposits, formed subsequently to the micaceous haematite bodies, were generated after deformation ceased, but under very high fluid pressure. The metamorphic reactions magnetite + quartz + H2O = grunerite + haematite and magnetite + quartz + H2O = grunerite + O2 were decisive in the formation of the metamorphic haematite deposits.

Jan 1, 2007

By T. Strong

"Selectively recovering pentlandite from high levels of pyrrhotite presents a technical and operational challenge. The liberation characteristics and also the chemical environment is critical to performing a successful separation. Reviewing the mineralogy to understand the characteristics of the ore and the plant flotation behavior is fundamental to designing a successful improvement program.At Savannah Nickel the challenges presented by a falling nickel price required a rethink of the flowsheet to improve the project economics through improving the concentrate grade and recoveries. Glencore Technology reviewed the plant performance and proposed and tested solutions to improve the grade performance of the concentrator with the support of the plant team. A pilot plant comprising a M20 IsamillTM followed by an L500/1 Jameson Cell was operated on various plant streams. In addition to the pilot plant, flotation surveys and a plant based laboratory program was used to supplement the plant understanding and within two weeks significant improvements were identified and demonstrated. The combination of the pilot operation and the plant based laboratory program was able to quickly demonstrate the improvements and test with equipment that is fully scaleable from pilot plant to full scale.IntroductionPanoramic Resources Limited is a Western Australian mining company formed in 2001 for the purpose of developing the Savannah Nickel Project in the East Kimberley region of Western Australia. Panoramic successfully commissioned the $65 million Savannah Project in late 2004. The process plant at Savannah comprises a single stage crusher, SAG mill, flotation, thickening and filtering stages to produce a bulk nickel, copper, cobalt concentrate. Metallurgical recoveries average 86-89% for nickel, 94-97% for copper and 89-92% for cobalt. The plant was originally designed for a throughput of 750,000 tonnes per annum, but has consistently outperformed the design specifications.Due to low nickel prices the Savannah Nickel mine and processing plant were placed into care and maintenance in May 2016. Prior to suspending production Glencore Technology was engaged to investigate options to improve the concentrate grade. With the discovery of Savannah North in 2014 and the Savannah North Scoping Study demonstrating LoM ~8 years and Mining Inventory of 6.07Mt @ 1.26% Ni, 0.64% Cu and 0.09% Co significant future potential exists. By completing pilot plant studies prior to shutting down, the plant engineering studies can be completed and the plant readied for restart by the time the nickel price improves."

Jan 1, 2017

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By H. R. Beard

The Federal Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environ¬mental conflicts, impacts, and occupational hazards Associated with mining and mineral processing operations. Tailings and soil samples from Wyoming and Utah were contacted with tailings liquors to determine the degree of absorp¬tion. Absorption ranged from 0 to 99 percent for radium and from 0 to 31 per¬cent for thorium. Some samples, which readily absorbed radium, were contacted with various salt solutions that could be present in tailings solutions to determine their effectiveness as desorbents. The desorption of radium ranged from 0.06 to 100 percent. An alpha-spectrometric method was used to determine the radium and thorium, concentrations in the solutions and the solids.

Jan 1, 1979

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

Some 50 miles of tunnel have been driven in the Snowy Mountains Area since tunnelling commenced in 1951. Hates have improved progressively due to the know-how of American supervision and use of large matched equipment of modern design.The work has been carried out by contractors, working almost exclusively under schedule of rates contracts. The Authority has maintained active research into tunnelling problems, especially that of support, and this has resulted in considerable economies and improved rates of progress. The contractors also have sought economies both by management and equipment techniques. Ammonium nitrate came into favour as an explosive essentially because of its lower cost, and handling techniques have improved progressively. Rock conditions preclude use of the "Mole" type equipment in its present stage of development, but one contractor introduced the "sliding floor" and this could exert a great influence on future tunnelling methods.Examination of tunnels that have been in service for some time confirmed the quality of the work and endorsed the policy of continued research and development.GENEHALThe Snowy Mountains Scheme provides for the diversion of the Snowy and Eucumbene waters through two transmountain tunnels to the western river systems. These diversions, together with additional regulations provided for waters already flowing inland, will provide an average additional discharge of 1,818,000 ac it per year for irrigation.Furthermore, approximately 6,000 million kWh of electrical energy will be generated annually in power stations with a total installed capacity of some 3,000,000 kW (Fig. 1.).INVESTIGATIONThe aim of investigation work is firstly to collect sufficient information to allow the overall scheme to be planned and then to follow up with detailed information on eachproject. The correct balance for all aspects of this work is a matter for keen judgment, as the tunnels must be planned...

Jan 1, 1963

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016