Search Documents

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By Xiyun Yang

Magnetite was prepared by hydrogen reduction method. For a conversion to cobalt-modified magnetite, magnetite particles were suspended into a solution containing Co2+ and Fe2+ to precipitate a cobalt ferrite layer on the surface. pH value influences the particle composition directly, the desirable CoFe2O4 is obtained when pH value is 12. The coercivity increases with the increase of cobalt content, cobalt efficiency reaches a maximum value at cobalt content of 2.71wt%. With cobalt modification, magnetite particles have similar lattice constant and squareness ratio to that without cobalt modification. TEM and XPS analyses indicate that acicular morphology is retained during the coating process, the epitaxial growth layer consists of CoFe2O4and 0.3Co2O3CoFe2O4 at cobalt content of 2.71wt% and 5.03wt%, respectively.

Jan 1, 2006

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

By Valentín Pamo

El presente trabajo describe los procesos y equipos que permiten la extracción de metales preciosos de la refinería de Ilo en condiciones agresivas, obligando a investigar materiales resistentes a la corrosión. Asimismo, se presentan alternativas que aseguren la continuidad de las operaciones en el proceso productivo de dicha refinería.

Sep 9, 2007

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By William H. Hamilton

INTRODUCTION It was not very many years ago that tunneling machine manufacturers spent considerable time trying to convince contractors and mine operators of the advantages of mechanical tunnel boring over conventional drill and blast methods. Today there are few doubters left. There is universal agreement that, not only are tunneling machines here to stay, but the ratio of bored rock tunnels to blasted rock tunnels is increasing at an accelerated pace, and within the next twenty years I predict almost all tunnels will be bored by machine. I believe we are today at a very important mile-post in the development of tunnel boring systems. Felix Gaye stated in his recent article (1) "It is important to disseminate between the efficiency of cutting tools and the overall efficiency of the boring operation". Mechanized tunnel boring in the past placed almost total emphasis on the rock cutting and boring ability of the tunneling machine. With advancements in technology and better solutions to the problems of rock fracture, steering control, and structural design, the emphasis today can be placed on the total-system concept. Tunneling machine design, as one of the key elements in the overall system, presents many problems that are not totally solved today. These design problems are, in the most part, not related with rock fracture, but rather with criteria associated with the over-all operation.

Jan 1, 1997

The evolution of surface mine layout configuration is a function of the schedules and sequence of material excavation within the optimized layouts. The production schedules and sequence of materials movement from multi-bench and multi-face operations are difficult to plan and execute. However, the ability to maximize the profit or net present value of an orebody is largely dependent on the mining schedule. The mining schedule will determine the life of the mine, the projected cashflows, and the investment requirements over the mine life. The pit geometries, pit expansion rates and the periodic volume of materials from different benches in a multi-bench, multi-face open pit mine determine the equipment requirements. The volume of materials excavated, as well as pit layout changes from circular and elliptical geometries of an oil sands mine were modeled using analytical geometric and parabolic partial differential equations (PDEs) and solved within Matlab. The results show that the geometric values are almost the same as those obtained from PDEs for different pit configurations. The economic analysis shows that both the current mining system (CMS) and the cyclic excavator conveyor belt control system (CycEx CBCS) are viable with high NPV (= $3.20 × 1010), PI (> 19%) and IRR (> 29.02%) with short discounted payback periods (= 3.24 months). The CycEx CBCS option is more economic than the CMS option. Its NPV is 1.27 times that of the CMS option. The PI and IRR for the CycEx CBCS option are respectively 2.24 and 1.13 times that of the CMS option. As well, the CycEx CBCS option has almost half the DPBP of the CMS option. The CMS option has an operating cost of $1.386 per tonne ($2.774/barrel) while that of the CycEx CBCS option is $0.779/tonne ($1.558/barrel). These results show that the CycEx CBCS option is the better option for mining companies working on oil sands deposits to invest in.

Jan 1, 2011

By Mark S. Sanders

There is a growing awareness among mining professionals that the human factor plays a significant role in safety and productivity. Since the 1960's, the science of human factors, or ergonomics, has been making inroads into the mining industry, and a considerable amount of research has documented human-factor-related mining problems and solutions. This Bureau of Mines report is directed toward summarizing the application of human factors to improving safety, productivity, and the general physical and psychological working conditions of miners. The aim of this report is to familiarize the readers with the role of human factors in the mining industry and the benefits that can accrue by systematically applying available human factors principles and data. The text contains 10 chapters dealing with human, equipment, and environmental factors. Each chapter builds on the previous chapter; therefore, it is recommended that the chapters be read sequentially However, if the report is used as a supplemental text, say in a mining safety course, chapters can be assigned in any order to supplement other readings.

Jan 1, 1988

By R. G. Garrett, A. J. S. Geddes

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The 1986 geochemical survey was successful in recognising all the previously known mineral occurrences of significance in Jamaica, in outlining areas not previously believed to have mineral potential and in stimulating fresh appraisals of old occurrences in terms of their potential for new commodities. This has resulted in a very significant increase in mineral exploration activity in Jamaica

Jul 1, 1991

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Phases of the Ir sub-group are present either as inclusions in or interstitially to chromite and are unaffected by (or only altered in situ during) hydrothermal processes. By contrast, almost all phases of the Pd sub-group are located in a secondary textural setting - in fractures in chromite or between fragments of brecciated chromite. The different settings indicate that the mineralisation episodes were associated with magmatic and hydrothermal stages respectively. The presence of an included Pd-group mineral in a hydrothermally Pd-group mineralised chromitite sample suggests that the hydrothermal Pd-group minerals were at least partly derived by remobilisation from magmatic deposits in the chromitite pod. These observations indicate that Pd-group elements are more mobile than Ir-group elements under hydrothermal conditions and point to the potential for hydrothermal platinum and palladium mineralisation in favourable environments

Apr 1, 1994

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By J. F. Lupo

Leaching operations combine both metallurgical and hydraulic processes to extract metals from the ore heap. In the design of leaching operations, metallurgical tests and simple hydraulic tests are often conducted to define operational parameters such as leach cycle time, application rate, lift height, and effective leach area. While metallurgical constraints are often the primary focus on leach facility design, the hydraulic factors are also critical to the overall success of the operation. Some of the hydraulic factors that are known to impact solution flow through heaps include: • Ore physical and hydraulic properties, • Variation in ore properties under heap loading, • Ore mineralogy and its susceptibility to chemical and/or mechanical degradation, and • Heterogeneities within the heap. This paper presents a discussion on hydraulic factors that may impact the effectiveness of leaching operations. In addition, methods are presented which may be used to assess flow conditions within active and inactive heaps.

Jan 1, 2000

State ownership of mineral in the ground is not newthe Regalian Right is an ancient concept. And the compulsory purchase of land and the minerals beneath it by the State or a body approved by the State (Fitzgerald, 1952) was a principle well established and enforced in practice over a hundred years ago, when such powers became a practical necessity during the period of railway building in Britain and elsewhere:The acquisition of mineral properties which stand in the way of public construction projects still goes on. But in recent years nationalization is being increasingly undertaken as part of the planned use of national resources, for the closer regulation of economic activities, or merely, so it would seem, as a matter of political expediency or national pride. For instance, the unsevered coal in Britain came under State ownership in 1938 in an attempt to simplify a complex pattern of freehold titles which were impedingplanned mining operations. Later, unsevered minerals became a factor in negotiations arising under various town and country planning acts. The acquisition of the Rio Tinto mines by the Spanish Government implies political aspirations. Or State purchase may even be accidental: it was the easiest course for the Sierra Leone Government consequential upon its failure to prevent widespread trespass over legally-held diamond privileges in 1955.This paper has been prompted by problems that have arisen when properties containing unsevered mineral have been expropriated by the Crown in New Zealand: expropriations, it is true, that have been on a small scale in rela...

Jan 1, 1957

By J. B. Gwiazda

S.S. Peng The highlights of this paper are : • The shield supports with lemniscate links will exert a tangential force on the roof strata, causing unnecessary and harmful roof movements, thus damaging the roof structure. The principal source of the tangential force is the horizontal movement of the point O, the pivotal joint between the canopy and the caving shield. When the support height is changed during setting, the point O will move along a curve upward and rearward toward the gob. As a result, it produces a vertical movement, causing the roof to move up a distance of ?d, and a horizontal movement toward the gob, creating vertical fractures in the roof. • The major purpose for employing the lemniscate-link system is to protect the hydraulic legs against the action of the bending moments induced by the tangential force that causes deformation or destruction of the legs. • Based on these two points, the author suggested that, in order to eliminate the harmful effects of the lemniscate-link system and strengthen its advantageous features, a shield support with a new design of that mechanism has been developed. With the new design, the conventional rigid lemniscate links are replaced by hydraulic rams. When the pressure inside the rams reaches a certain level, the ram will yield.

Jan 12, 1986

By William R. Yernberg

The Fifth International Heavy Minerals Conference (HMC) was held Oct. 16-19, 2005, at the Marriott Sawgrass Resort in Ponte Vedra, FL. With SME as sponsor, the 2005 conference marked the first time that the HMC was held in North America. The conference is held every two years and provides an important forum for professionals in the heavy minerals and related industries to meet and discuss issues related to heavy mineral exploration, mining, processing and marketing. Previous locations included Australia and South Africa. The conference consisted of technical presentations, field trips to heavy mineral operations, a trade show and social activities. It was appropriate that Ponte Vedra was selected as the location for the conference. Ponte Vedra, located on the Atlantic Coast 17 km (10 miles) southeast of Jacksonville, FL, is the birthplace of heavy minerals mining in North America. Ponte Vedra beaches were mined from 1916 to 1929 in what was then called Mineral City. Though Ponte Vedra is now a golf and beach resort, there are still four heavy mineral mines operating within an hour’s drive. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site.

Jan 1, 2006

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006