Search Documents

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

THE treatment by chlorination of the Mount Morgan Gold Mining Company's ores was first accomplished, early in 1886, by a works having a capacity of 25,000 tons per annum. Shortly afterwards another works was established, capable of dealing with 50,000 tons per annum. The extraction of gold was originally successful and satisfactory, but running expenses were high, averaging £2 19s. 6d. per ton of ore treated. These works were believed to be the largest chlorination pJants in the world at that time. As might have been expected, the mechanical details and chemical process had not been perfected, and, moreover, both works were hurriedly built, and operating expenses were not then considered of such prime importance, as the ore at that time was of very high grade the large quantities of low grade ore since dealt with not being then considered, since the bulk of it was not even known to be in existence.These two works consisted of lock-breakers, high speed rolls, screens, elevators, &c., for crushing; a large number of small handrabbled reverberatory furnaces for roasting; one-ton chlorination barrels and three-ton leaching vats for chlorination.

Jan 1, 1910

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By Richard Crockford

The World Trade Center (WTC) is located on the west side of Manhattan in New York City, approximately 0.5 miles north of Wall Street, and is owned and operated by the Port Authority of New York and New Jersey (PA). As part of the WTC site redevelopment the New York City Transit Authority?s No. 1 subway line which runs through the site below grade, was underpinned so that the soil beneath it could be removed along with the rest of the new east basement excavation. Consequently a scheme comprising micropile installation through and around the existing subway box was designed. The subway had to remain in use throughout save for planned weekend outages to allow a portion of the underpinning to be fitted through or on to the existing structure. At times this involved accessing and drilling from within the subway tunnel under short General Order (GO) Subway shutdown periods. At either end of the subway passage through the WTC site jet grout underpinning was designed to provide support and to complete the excavation and construction of the east basement wall in the areas beneath the subway where it was impossible to install a slurry wall. The jet grout blocks thus formed had to be largely installed around the clock during 53 hour long GO weekend outages and had to overcome severe logistical constraints in and over the tunnel. The jet grout blocks had to provide strengths of at least 500 psi at 3 days and 700 psi at 28 days. The jet grouted soil mass also had to have a level of permeability less than 0.03 feet/day (1 x 10-7 m/s). After an extensive trial program and then production testing it was concluded that the glacial till above the rock proved to be a particularly difficult soil strata to collect test data from and hence the level of observational monitoring was increased to progress the excavation works. Throughout the installation of micropiles and jet grout columns extensive monitoring was in place and prompted a variety of working method changes. The work described in this paper was performed by the Nicholson Construction Company/EE Cruz Joint Venture.

Jan 1, 2008

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

Australia has a long history of underground mining. Even withadvances in open cut mining equipment, techniques andeconomics, many orebodies are still best mined by undergroundmeans. In addition, modern exploration tools are æuncoveringÆorebodies that are at increasing depths. South African mines arecurrently producing from below 3 km, and developing down to5 km depths û it is likely that Australian mines will also becomemuch deeper over the next 20 years. One of the most significanttechnical challenges in deep mines is the problem of heat.Community expectations and legislated standards continue todrive operations towards improving the working conditions inmines. The hazards and costs associated with chronic hotworking conditions (heat illness, poor safety, poor productivity,higher operating costs and poor morale) are also becomingincreasingly recognised (Brake, Donoghue and Bates, 1998). Theexposure of miners to many other occupational hazards has beenreduced over the past 50 years. However, despite air-conditionedcabins greatly reducing the heat stress on mobile plant operators,there are still many Australian mine workers subject to levels ofthermal stress that existed a century ago. There are severalreasons for this, including a frequently-poor understanding of thephysiology of working in heat by mine management, no agreedmining code of practice for working in heat, the lack of a robust,practical-sized instrument to measure heat stress, the costpressures on the industry and, to some extent, deep-seatedtraditional management and worker practices. Howeversignificant progress has been made in many of these areas (Brakeand Bates, in press), with the net result that there is likely to be a trend towards installation of refrigeration of some form in manyAustralian mines in the future. This will add directly to the costof operation, but will also have direct and indirect benefits,including cost benefits. It should also be noted that Australia isnot at the forefront of adopting practices to manage temperaturesin the workplace: South African metal mines usually haverefrigerated cooling, and Canadian mines spend large sums onheating, with heating costs (averaged over a full year) of up to$A1 per tonne mined (Bandopadhyay et al, 1997). The history of mine refrigeration dates back to 1919 when thefirst plant was installed at Morro Velho, Brazil. By 1965, the totalinstalled capacity (worldwide) reached about 100 MW(R)i. Since 1965 the growth in mine refrigeration capacity has beenexponential, with a doubling every six or seven years (Howes andNixon, 1997). South Africa is by far the largest user of minerefrigeration, with over 300 refrigeration machines installed. This paper discusses the key design issues associated with theapplication of refrigeration in underground metal or coal mines.Whilst the emphasis is on large, surface plants, small, surface orunderground refrigeration plants can also be very effective in thecorrect application and many of the principles of design andoperation are the same.

Jan 1, 2001

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By X. Louw

"This paper examines the change in surface properties of the Polyurea used on spirals at different operational times: unused spiral, 28 months in operation and 58 months in operation. This is being done to investigate the alleged statement that spirals have a decrease in spiral separation efficiency after a certain period of operational time. Observing the surface characteristics under 1.5x and 36x magnification it can be concluded that the surface roughness decreases with increased operational time. This may be explained by a decrease in air inclusions and streak lines as the spiral surface wears. Decreased surface roughness should in theory have a beneficial effect on spiral separation performance. This leads to the conclusion that if a decrease in spiral separation performance is observed after a certain period of operation, it can’t be attributed to the change in surface properties. Uneven wear of the spiral surface, material creep or application of force to the spiral will change the profile of the spiral and could cause an adverse effect on spiral separation performance. The metallurgical test work showed that the best results are obtained at 30 - 35% solids by mass in the spiral feed. The iron recovery was significantly higher in the new spiral in comparison to the 2012 and 2010 spirals. The mass yield to concentrate in the new spiral was approximately three times more than for the older spirals. In conclusion, the yield combined with the grade, which equals the recovery was the best for the new spiral.IntroductionAn investigation was launched to research the common belief that spirals experience a decrease in efficiency, and therefore recovery, after a certain period of operation (a period of seven years has been used in the industry). The properties of the spiral that may have an effect on the efficiency are:"

Jan 1, 2017

By Randy Wheeler

One of the more difficult topics to address concerns the effects of vibration on historic structures. Not only blast induced vibration, but also vibration from other transient and semi-continuous sources like, traffic, human activity, and environment forces. A common question might be, “What level of blast-re l a ted PPV is considered safe?” A review of some of the papers available from the ISEE Explosives Reference Database on CD ROM shows that 0.50 inch per second was often used. It was not clear on what basis this value was selected except that it represents the low frequency limit for plaster developed by the United States Bureau of Mines in RI 8507. In another case, a limit of 0.20 inch per second was mentioned, apparently simply because it was ten times less than 2.00 inches per second.

Jan 1, 2004

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

ONE DAY IN the mid-1880s, in a suburb 0f Pittsburgh, Pennsylvania, there dismounted from a train the two foremost leaders of the day in the coal and steel industries-Andrew Carnegie and H. C. Frick. Their attention was drawn to a well-loaded car of coke, which their experienced eyes recognized as a superior product. "I'll bet you that coke is from the H. C. Frick Coke Company," Mr. Frick challenged. "I'll bet it was shipped by my company." In a spirit of fun Mr. Carnegie accepted the wager. Mr. Frick lost the bet: the coke had come from M0rewood, one of three sites being operated under the direction of a young entrepreneur, Erskine Ramsay. If Mr. Frick's confidence was somewhat dented by this occurrence, the responsibility was his own. He himself had opened the way for Erskine Ramsay to become the youngest of mine superintendents; and he had dispersed all dissension regarding his choice with the words : "I'm not interested in his years, I'm interested in his record. He makes more coke in an oven than any other superintendent. And I'll take 'em out 0f the cradle if they can make coke... Suppose he is only twenty years old? ... The d --- kid is a genius, I tell you." Erskine Ramsay was to follow in the tradition of Carnegie and Frick. Not only was he ambitious and a worker his background had prepared him for it. Coal mining was in the Ramsay blood. His father, Robert Ramsay, of whom the son once stated that he had no superior as coal mining and mechanical engineer in this country, once accounted in these words for the phenomenal accomplishments which had attached to the name "It does no harm to belong to a family of mining engineers who are just as good as any in America-if it is myself that says it." Anyone acquainted with Robert Ramsay's character realized that he was not given to overstatement. And the above-mentioned Mr. Carnegie encountered young Ramsay again, a few years later in his career, and wrote of him to young Erskine's father, that he was "going to be a credit `tae us a' " (a quotation from Robert Burns.) Nor have Mr. Ramsay's achievements been identified exclusively with the industrial field in which he early asserted himself. He has been an inventor whose techniques in mining engineering have received international recognition. As an investor of foresight, he has benefitted others immeasurably, as well as himself, being an influential factor in the upbuilding of several communities in his chosen and well-loved adopted home state of Alabama since 1887. He is a philanthropist whose benefactions have run into millions, the chief beneficiaries being educational and charitable institutions. Amidst his accomplishments the lighter side of life has not been neglected and he is known for his hospitality, his

Jan 1, 1953

By R. Lombard

"Water is a very important component in the production process at underground coal mines. Current unfavourable economic conditions have forced the coal mining industry to identify and address every possible bottleneck preventing optimal production. An increase in water-related downtime was identified as one of the bottlenecks at Goedehoop Colliery’s Vlaklaagte Shaft. The purpose of this project was to identify the various causes that contributed to the high downtime (501 hours in 2013, which led to a potential profit loss of R12.9 million) and to suggest possible solutions.After a thorough investigation the main causes of water-related downtime were identified as low water pressure and low water flow caused by pipe leakages and bursts. The main root cause for the low water flow and pressure was identified as being the low pressure resistance (1600kPa) of the thin-walled galvanized steel pipes used in the underground inbye water reticulation system. The pipes were selected according to the previous 1000 kPa pressure requirement for the continuous miner. However, the pressure requirement changed to 1500 kPa, which resulted in the pipes being exposed to much higher pressures than designed for.The water reticulation system was reviewed and current and future underground pipe layout and water requirements were determined for the shaft. The time frame in which the water consumption would be the highest was determined to be between 1 January 2014 and 7 September2014. Machine and sprayer specifications were used to determine theater consumption at the shaft. Three different solutions were considered to solve the water-related downtime problem and to ensure the efficient supply of water to the newly open sections. Permanent underground concrete dams, semi-mobile dams, or new pipe columns with a higher pressure resistance of 3200 kPa were considered. A trade-off study (taking into consideration cost, time to completion and ease of implementation, maintenance requirements, safety, and flexibility) was completed to determine which of these solutions would be most viable.Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Engineering)"

Jan 1, 2015

This Bureau of Mines publication presents an overview of mine electrical power systems research currently being conducted by the Bureau. The papers, given at a Technology Transfer Seminar, emphasize the increasing importance of research related to the safety considerations of underground coal mine electrical systems. Selected topics are included that summarize results of research in the areas of electrical shock prevention, explosion-proof enclosures and load centers, discriminating circuit breakers, and trailing cables. Other topics discussed at the seminar are published as separate sections of the Bureau of Mines Hand- book "Application Notes--Mine Electrical Power Systems."

Jan 1, 1982

By Hargraves A. J

The paper outlines events at the Collinsville State Coal Mine, Queensland, leading to the practice of full face multiple shotfiring in bord and pillar development places. The 1954 disaster is referred to, and factors involved in simultaneous shotfiring in coal are discussed. Promising preliminary multiple shotfiring tests at the Colliery are described, as well as the resulting routine measures adopted, and the changes involved. The subsequent inducing of two outbursts under safe conditions by remote multiple shotfiring is given as justification for the changes made.INTRODUCTIONFollowing a disastrous instantaneous outburst (1.0.) of coal and gas at the Collinsville State Coal Mine in 1954, the necessity for inducer shotfiring for the control of possible further outbursts was established. However this mine, immediately classified as gassy after the 1954 outburst, is subject to the general restrictions pertaining to gassy mines which at present preclude the use of inducer shotfiring due particularly to the non-existence of a permitted exploder for more than six shots, and further, because permitted multipleexploders are not designed for remote firing through long lengths of cable. This situation was met by arresting or reducing progress in the production places, thereby reducing the danger of outbursts while means were being considered to achieve overall maximum safety.In August 1957 two full faces were successfully blasted in experimental simultaneous rounds. In June 1958 four full faces were blasted, and in October 1958 full face grunching without prior cutting, Le. inducer shotfiring, was introduced in No. 1 Tunnel as a production feature. In March 1960 it...

Jan 1, 1960

The last one decade in India had witnessed phenomenal growth in the coal, lignite, iron ore, limestone and many other minerals. To meet the production of minerals, the energy requirement is also very high both in terms of petroleum products and electrical energy. Because of spiralling prices of crude oil and also of the electrical energy, attempts have been made by various mining companies to select energy efficient mining machineries (in underground and surface) mines, together with energy efficient mining and mineral processing operations. Mineral sector of India is working seriously in tune with the Planning Commission stipulations to conserve energy.Apart from energy use (both electrical and fossil fuels) in mining, it is also significantly contributing to the cost of mineral processing depending on the quality of ore/rock being processed. Over the years a number of studies have been initiated and implemented to reduce cost of energy bill. An attempt has been made to present the various aspects of energy conservation, Impact of Energy Conservation Act 2001, Relevance of energy audit, areas of energy consumption and conservation efforts, etc in this paper. The paper also deals with some of the case studies to show how energy conservation programs has been implemented in the Indian mineral sector.

Dec 6, 2010