Search Documents

By J. E. Hawley

Abstract Spectrographic methods for the analysis of minor constituents such as platinum-group metals, gold, silver, and silica in palladium and platinum refinery sponge are described. These involve the conversion of the sponge metals to the black form by reduction with high purity aluminum filings in either acid or alkaline media. Standards of known composition are prepared in the same manner from either refinery or spectrographically standardized sponge metals. Samples of the black metals are mounted in pellet form and a multisource spark discharge used for excitation. The range of concentrations of impurities studied are those common to refinery samples. Excellent reproducibility of intensity ratios using major constituents as internal standards, is demonstrated and two methods have noted by which the accuracy of the procedures are shown to be of the order of 3 per cent, on the basis of synthetic preparations. Introduction During the past two years an investigation has been carried out in the Spectrographic Laboratory, Queen's University, to determine the suitability of modern spectrographic techniques for the precise analysis of the platinum-group metals palladium, platinum, rhodium, iridium, and ruthenium in the form of refinery sponge analyzing about 99 per cent of the major constituent.

Jan 1, 1951

By F. E. Crane, H. A. Kendall, G. H. F. Gardner

Two effects of a difference in density may be observed in miscible displacement. As the difference is increased from zero there is first a change in mode from multiple fingers to a single finger. A further increase results in a more rapid growth of the single finger. Miscible displacement with multiple fingers has been discussed by Blackwell, et al, whereas miscible displacement with a single finger has been discussed by Craig, et al. In the present paper experiments are described which bridge the gap between these extreme cases. INTRODUCTION Craig, et al,1 investigated the effect of gravity on frontal displacements for circumstances in which the gravity forces were significant. Blackwell, et a1,2 dealt with the other extreme in which gravity forces were negligible. The considerable difference between their results is illustrated in Fig. 1 where the breakthrough recoveries are plotted against the mobility ratio. The experiments described in the present paper were conducted to examine how the transition from the one extreme case to the other occurs when the gravity forces are gradually reduced. The transition is well illustrated by the production history after breakthrough. Fig. 2 shows how the number of pore volumes which must be injected at a constant rate to displace 98 per cent of the original fluid depends on the gravity force. For each mobility ratio there is a transition range, and a very significant change in the number of pore volumes occurs when this range is traversed. This range of the gravity force is physically linked with the formation of viscous fingers. A single finger is predominant for larger gravity forces; a multiplicity of fingers is formed for smaller gravity forces. Improved recovery and the occurrence of multiple fingers is concomitant with a large increase in the amount by which the fluids are mixed within the porous medium. The transition range depends on all the dimension-less groups which characterize the problem; but this dependence has not been exhaustively studied as yet and only fragmentary results are discussed in this paper.

By F. M. d’Heurle

Films of molybdenum have been prepared by sputtering onto oxidized silicon substrates. The resistivity. lattice parameter, orientation, and grain size were studied as a function of substrate temperature and substrate bias. Under normal sputtering conditions, the resistivity of the films was found to be quite high (600 x 10 ohm-crn). However, with the use of the negative substrate bias of 100 v and a substrate temperature of 350°C, films weve produced with a resistivity of ahout twice that of bulk molybdenum. The lattice parameters measured in a direction nornzal to the surface of the films weve found to be gveatev than the bulk value. This was interpreted as being at least partly due to the presence of compressive stresses. The effects of annealing in an Ar-H atmosphere were studied in terms of diffraction line width, lattice parameter, and resistivity. BECAUSE of its relatively low bulk resistivity (5.6 x 106 ohm-cm)' molybdenum is potentially interesting as a thin-film conductor in integrated circuits. An additional feature which makes it attractive for this purpose is its low coefficient of expansion (5.6 x KT6 per "c),' which is fairly well matched to that of silicon (3.2 x 10 per c). It is possible to deposit molybdenum films by evaporation but generally films produced in this manner have a high resistivity. In order to achieve resistivities close to bulk value, Holmwood and Glang found it necessary to operate in a vacuum of about 107 Torr and to maintain the substrates at 600 C during film deposition. Sputtered molybdenum films have been examined by Belser et a1.7 and, recently, by Glang et al.' This paper describes the results of an attempt to extend some of that work and examine the effects of annealing and getter sputtering on the physical and structural properties of the films produced. SPUTTERING APPARATUS AND PROCEDURE The apparatus used for most of the film sputtering work described here consisted of two "fingers" serving as anode and cathode, respectively, which were mounted within an 18-in.-diam glass chamber. A liquid nitrogen-trapped 6-in. diffusion-pump system was used to achieve a vacuum of about 1 x 107 Torr within the chamber prior to sputtering. The essential features of the equipment are shown in Fig. 1. Cathode and anode fingers are stainless-steel tubes isolated from the top and bottom plates by Teflon collars. In order to limit the discharge to the space between anode and cathode, each finger is surrounded by an aluminum hield, at ground potential, having an internal diameter 18 in. larger than the outside diameter of the finger. The cathode and anode fingers are 6 and 4 in. in diam, respectively. A 116-in.-thick sheet of molybdenum is brazed with a 10 pct Pd, 58 pct Ag, 32 pct Cu alloy to a copper disc which is mounted by means of screws and a large 0 ring onto the lower end of the cathode finger. The disc is cooled during sputtering by water circulation inside the finger. The use of several feet of plastic tubing for the water input and outputg reduces leakage to ground to less than 1 ma when the cathode potential is raised to 5 kv. The upper end of the anode finger is terminated by a brazed-on copper block. A variety of specimen holders can be easily mounted on the upper face of this block. Substrate heating or cooling is achieved by use of an appropriate unit attached to the lower face of the same block. Heating is achieved by means of cartridge-type heaters and cooling by copper coils fed with forming gas under pressure. The inner chamber of the specimen finger constitutes a small vacuum chamber of its own which is evacuated by an auxiliary mechanical pump in order to limit heating element oxidation and heat transfer by convection currents. An advantage of the finger arrangement is the absence of cooling and heating coils and wires within the main chamber. The stain less-steel shutter is useful to establish a discharge for cleaning the cathode at the beginning of each sputtering run. Water cooling of the shutter reduces heating and the out-gassing of impurities which might condense on the nearby substrates. Unless otherwise specified, the substrates used in these experiments were 1-in.-diam oxidized silicon wafe:s, 0.007 in. thick, having an oxide thickness of 6000A. The substrate holders were large copper discs onto the surface of which a number of molybdenum discs, 116 in. thick and 78 in. in diam, were brazed. The wafers were clamped to the molybdenum discs

Jan 1, 1967

By P. D. R. Maltby

This paper describes the background and markets for calcium carbonate and silica sand in Canada, as well as the results of recent test work carried out at the Ontario Research Foundation. Tests on sericite, tremolite, vermiculite, barite and graphite are also mentioned.

Jan 1, 1979

By R. P. Agarwala, M. S. Anand

Using residual activity technique, the diffusion of palladium, silver, cadmium, indium, and tin in alunzinum has been studied in the temperature range of 400" to 630°C. The diffusivities (in units of square centimeters per second) have been expressed as: IMPURITY diffusion in aluminum,1-9 silverand lead5 for cases of low solid solubility of the impurity in the host metal has yielded frequency factors in the range of l0-6 to l0-9 sq cm per sec whereas the activation energy is practically half the self-diffusion activation energy value. From the observed values of frequency factor, activation energy, and entropy of activation, it has been suggested' that these solutes are not diffusing by vacancy or interstitial mechanisms but by a mechanism which should be consistent with such low values of the diffusion parameters (Do and Q). However in spite of extensive work on these types of systems, the mechanism of diffusion is still not well understood. The present investigation on the diffusion of palladium, silver, cadmium, indium, and tin in aluminum has been carried out to throw further light on the diffusion mechanism in systems, where the solid solubility is very low (except for the case of silver). The results are discussed on the basis of solid solubility and the structural changes involved owing to the presence of the solutes in aluminum solid solution. An attempt has also been made to apply the existing theories of charge5-8 and size8 difference between the solute and the solvent. EXPERIMENTAL PROCEDURE Specimens (1/2 in. diam by 3/8 in. high) were machined out of pure aluminum (99.995 wt pct) rod obtained from Johnson Mattheys. They were sealed under vacuum in quartz tubes and annealed at 620° C for several hours; the grains thus developed were sufficiently large to eliminate the possibility of diffusion along the grain boundaries. The flat ends were prepared carefully after polishing as described previously,10 Radioactive nitrates of cadmium, indium, and tin and chloride of palladium containing, respectively, cd115, 1n114, sn113, and pd103 were dissolved in distilled water and mixed with 30 pct acetone. By means of a micropipet a drop of this solution was placed on a smoothly polished and lightly etched surface of the specimen. Due care was taken to see that the solution spread uniformly on the surface of specimen without trickling down its sides. Radioactive silver was elec-trodeposited using a AgCN-KCN bath. The amount of sample deposited in all the cases was not more than 0.1 µ thick. The samples were then sealed in quartz tubes in vacuum. The cadmium samples were sealed in a purified argon atmosphere to avoid evaporation. The samples were then diffusion-annealed. The temperature of annealing varied between 400° and 630°C and was controlled to ±5°C. On heating to -400°C,the deposits of cadmium, indium, and tin, which were of the order of 0.1 p in thickness, were converted to their respective oxides. The contribution of oxygen present in the lattice of aluminum due to these oxides has been calculated and found to be less than 10 ppm in all cases. Oxide method has already been used by other workers11'12 in diffusion studies without any controversy on the issue. However, in some of these investigations, metallic deposition was also tried. The diffusivities calculated from these measurements were found to agree very well with the diffusivities obtained by using the oxide method. Thus it is assumed that the measured diffusivities represent true diffusion coefficients. Since palladous chloride decomposes at about 500°C, the deposited samples which were to be diffusion-annealed below 500°C were heated in vacuum for a very short time at 500°C to allow the decomposition of palladous chloride to palladium metal. Time taken in decomposition of nitrates to oxides and chloride to metal was negligibly small as compared to the period of the diffusion anneals. The residual activity technique13 was used to study the diffusion profiles where thin layers from the specimen surface were removed by grinding it parallel to a flat surface on a 600-grade carborundum paper. The specimen was washed, dried, and weighed, the differ -ence of the weight being the measure of the thickness of the layer removed. After each such abrasion and weighing, the total residual activity on the surface of the specimens was measured by counting 0.656, 0.94,

Jan 1, 1968

By J. L. Roll

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) and the regulations promulgated for that "Act" have resulted in changes to surface mining operations in order to comply with the stringent federally enforced reclamation requirements for prime farmland. In many instances the operator has modified surface mining operations to meet the prime farmland requirements through changes to mining equipment operation, addition of new equipment targeted for reclamation or the use of totally different mining techniques. The major challenge to mine operators has been how to use existing mining equipment to meet the requirements of the "Act." Freeman United Coal Mining Company opened the first new large surface coal mine in Illinois following passage of the "Act." The Industry Mine, located near Macomb, Illinois started mining operations during March of 1982 and was required therefore, to meet all of the requirements of the "Act" including prime farmland restoration. At the Industry Mine a shovel and a cross-pit bucket wheel excavator (wheel) are used for overburden removal and the wheel is addition- ally utilized to assist in reclamation operations. The wheel mines the subsoil thereby elliminating scraper placement of that subsoil and the attendant compaction problems with scraper placed subsoil. The wheel is used to convey topsoil stock- piles from the highwall to the mined overburden in order to lessen scraper traffic and possible compaction on the graded overburden during top- soil removal and replacement. Close control of the operation of the wheel yields more uniform wheel spoil ridges which then require less grading prior to topsoil replacement.

Jan 1, 1986

By F Flitti, M Haest, O Dominguez, D Mittrup, G Hird

The automated geology interpretation (AGI) tool has been developed in BHP Billiton to automate stratigraphy logging of drill holes, using any available quantitative data sets. At present, AGI is set-up to utilise geochemistry and mineralogy from infrared spectroscopic data to predict stratigraphy. Once the AGI tool is calibrated, results show that the tool is capable of automatically defining stratigraphy across all of the deposit types, encountered by BHP Billiton Iron Ore in the north-west of Western Australia. Accuracy of AGI at predicting stratigraphy is on average better than 75 per cent, with average accuracies exceeding 85 per cent for some deposit types. The AGI tool can deliver fast, accurate, consistent and objective geological interpretations.AGI is currently being implemented in BHP Billiton Iron Ore Exploration to streamline the drill hole logging process and allow geologists to spend less time defining stratigraphy at the drill hole level and more time investigating stratigraphy in 3D. This will deliver improved geology models, with significant downstream benefits in terms of better resource models, more accurate mine plans, higher plant efficiencies and more consistent ore products, driving productivity in BHP Billiton Iron Ore over the next decade.CITATION:Mittrup, D, Flitti, F, Hird, G, Haest, M and Dominguez, O, 2015. Semi-automated geological interpretation using assay and infrared spectroscopic sensing parameters towards improvements in geological modelling, in Proceedings Iron Ore 2015, pp 313–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By J. J. Lui

Surfactant plays a critical role in many industrial processes such as petroleum, mining, environment and food processing, and daily life. For ionic surfactant systems, adsorption of surfactant at oil-water interface imposes a net charge to the interface. The nature and magnitude of the charges at the oil-water interface depend on charge characteristics of surfactant molecules, concentration of surfactant and solution pH. In our previous study, zeta potential measurement of hexadecane drop-lets in industrial process water was shown to be a simple, yet powerful method for identifying various types of ionic surfactants present in the aqueous system. In this paper, the site-binding model was applied to prediction of zeta potential of oil droplets in aqueous solutions containing a mixture of cationic and anionic surfactant molecules. The total number of interfacial sites for various types of surfactant involved was determined by applying the Gibbs adsorption equation to the measured interfacial tension-surfactant concentration profiles. The distribution of various types of surfactant molecules at the interfaces was evaluated by Langmuir isotherm constants. With the ionization constant of surfactant taken from the literature, the predicted zeta potentials of oil droplets in surfactant solutions from site binding model were shown in a reasonable agreement with the measured zeta potential values.

Jan 1, 2014

By I. Govender

Positron-Emission-Particle-Tracking (PEPT) has enabled the non-invasive observation of charge and slurry transport in model mills under operational conditions. We use high quality PEPT data to infer that the charge motion can be effectively described by a non-Newtonian granular fluid. An improved theory for slurry transport, including inertial effects, is presented.

Jan 1, 2012

By Claude K. Howse

The area covered by the present paper consists of about fifty square miles in the immediate vicinity of the settlement of St. Lawrence, which is on the Southern extremity of the Burin peninsula on the south coast of Newfoundland. Physiography Physiographically, the area is part of the Atlantic upland, equivalent to the New England province of the United States. Evidences of two erosion surfaces are to be seen truncating the intrusives and the folded volcanics and sedimentary rocks. The older erosion surface is represented by small monadnocks from 650 to 750 feet in height with the younger surface covering most of the area and characterized by rounded subdued topography with maximum relief of two to three hundred feet and numerous ponds and bogs. These surfaces have been correlated with the High Valley and the Lawrence peneplains of Newfoundland. On the Avalon peninsula, these peneplains have elevations of, respectively, from 1,300 to 1,700 feet and from 500 to 1,000 feet. Glaciation The entire peninsula has been glaciated, with lee-and-stoss slopes showing on the highest hills in the immediate vicinity, many of which have striae and erratics on their summits. The lee-and-stoss slopes, the glacial striae, and the distribution of certain rocks found in the drift and whose source outcrops are known, indicate a southward direction of ice movement.

Jan 1, 1951

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result- ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coalbed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beck- ley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Autumn Fjeld

The filling and solidification of an industrial scale composite casting has been simulated to investigate the re-melting of the outer shell material during casting. Production of a composite requires a two-step casting process which includes centrifugal casting of a hard outer shell material and subsequent conventional ingot casting of a tough core material into the shell-mold assembly. During casting of the core, a thin layer of the shell material re-melts and mixes with the core material producing a bonding layer of intermediate composition. The present numerical model employs the volume of fluid method and an enthalpy-porosity technique to couple the filling of the core material and re-melting of the shell material. The interface between the two materials is tracked and can be used as a guide to examine the extent of melting and, to some degree, mixing of the two fluids and species diffusion.

Jan 1, 2008

By V. H. Wilhelm

WITH rapidly diminishing oil reserves: a great percentage of which are uneconomical at present prices, some of the existing methods of development and production will have to undergo radical re- visions to meet the changes continually taking place in the petroleum industry. Imagination in an engineer is a great asset. The fancy of today is found to be the realization of tomorrow, and with this thought in mind, there is here presented a more or less imaginative picture which, to my mind, has a meritorious basis. Directed drilling has reached a stage of accuracy sufficient to allow the prediction that this art will be used in the future development of oil structures, especially those \\,it11 thin sand bodies 'and steep dips. Directional drilling in a number of fields in California has gratifying results. Wells which practically laid pipe lines through the oil sands have enjoyed a greater drainage radius with a consequent greater initial and cumulative production. In one field where the vertical thickness of sands was approximately 550 ft., wells drifting at an angle as great as 55 deg. fro111 vertical had over 1100 ft. of perforated pipe in contact with these sands. These wells were, and are, remarkable for their great initial pro-

Jan 1, 1936

By Gregory M. Molinda

Coalbed discontinuities historically have been hazardous to mining as well as obstructions to efficient production. An effective means of mapping these features is needed in order to plan safe and efficient mine development. This Bureau of Mines report discusses the use of surface seismic techniques for this purpose. At a southwestern Pennsylvania mine, a system of coalbed discontinu-ities (paleochannels) was accurately mapped by the Bureau of Mines using borehole log methods and underground observation. This site was chosen to test the value of a high-resolution surface seismic reflection on technique for coalbed mapping. A statistical study performed at this mine indicated that the probability of accurately delineating this paleochannel system with conventional borehole methods was remote. A total of 1.47 miles of high-resolution seismic survey, comprised of four seismic profiles, was conducted in known and suspected coalbed discontinuity areas. Several test holes were drilled on the seismic lines in order to evaluate the interpretations. It was found, based on these and other existing boreholes, that it is possible to predict these dis-continuities. Paleochannel washouts were correctly predicted in several instances but in other instances were either incorrectly predicted or not predicted in areas of known discontinuities.

Jan 1, 1988

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company's underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine cool by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 1, 1950

By Rudolph Emmel

The mines operated by the South American Development Co. are located in the Zaruma mining district of southwestern Ecuador. They are near the old mining town of Zaruma, which is the only important city in the canton of the same name. The district is situated in the upper end of a valley lying between two spurs of the Cordillera, one of which may be considered the Coast Range and the other an intermediate range. The mining camp proper, known as Portovelo, and the plant are 2.4 km. south of Zaruma, on the north bank of the Amarillo River, a tributary of the Tumbes River, which flows southwestward through Peru to the Pacific. Portovelo is difficult of access; it is reached from Guayaquil by means of river steamers and muleback. 'Embarking at Guayaquil, the route is down the Guayas River, across the Jambeli Canal, and up the Santa Rosa River to Santa Rosa, a distance of 177 km. From Santa Rosa, the road or trail follows the Santa Rosa River, then across the summit of the Coast Range into Portovelo, a distance of 74 km.—a two-day trip on muleback. The mining property of the South American Development Co. comprises 297 lode claims and 142 placer claims. The combined lode claims cover an area, roughly rectangular in shape, 9000 m. long from north to south by 4000 m. wide; the northern edge of the rectangle is about 3000 m. north of the central plaza of Zaruma. Mineral lands in Ecuador are held by virtue of an annual tax per claim paid to the central government, no surface rights being included. HiSTOry The Zaruma mine has been worked by white men since 1549, probably before that it was worked by Indians. The followers of Pizarro, led by traces of gold in the sands of the Tumbes River, followed that stream to its source, worked the gold veins that they found and established the city of Zaruma. Among the mines worked by them were th Sesmo, Leonora, Viscaya, and Mina Grande. Only the soft ores at the outcrop were

Jan 1, 1925

By L. A. Cowan

IF the elements of personality be those characteristics in which humans differ, and if this definition be applied to the purchasing department for the Climax operations in Colorado, it must he concluded that this department has no distinguishing traits that would give it a departmental personality different from that possessed by the similar department of any progressive mining enterprise. Or, one may go further by stating that the rudimentary functions of any purchasing practice employed principally in the acquisition of maintenance, repair, and operating supplies are much alike, whether or not the industry involved be mining or milling. However, in the fact that the principal purchases of a mining company are materials for maintenance and repair and consumable operating supplies lies that essential characteristic which differentiates mining and milling purchasing functions from those of the manufacturer, the fabricator, or the ordinary processor.

Jan 1, 1946