Search Documents

By A Maldonado, A Robert, K G. Mercer

The Hamersley Group in the Pilbara, Western Australia, consist of interlayered banded iron formation (BIF) and shale host rock formations within which a large number of open pit iron ore mines have been established. The slope stability of most of the mining excavations developed within these formations is controlled by the relatively low shear strength of the shale groups and shale bands, which are the weakest rock types. Shale formations range from fresh to highly weathered and are generally highly fissile when fresh, and clayey when weathered. An accurate understanding of the shear strength of these materials across the entire weathering continuum is therefore a key importance for assessing the slope stability of these mines.Historically defect laboratory testing results for the Pilbara mines have been analysed mechanically using direct shear testing (DST) to measure a number of geotechnical characteristics of the rock bedding and defects. This paper sets out the current practice in the industry in terms of the laboratory testing and presents a possible application of hyperspectral data to empirically correlate the shear strength of shale bedding with the relative mineralogy abundance on the bedding surface. This was achieved by creating both hyperspectral and geotechnical data sets for the same samples.In the study the shale samples were separated into three distinct assemblages: iron oxide + kaolinite, iron oxide + white mica + kaolinite, white mica + kaolinite, which had 40, nine and two samples respectively. Analysing these assemblages alongside DST data showed that samples with white mica had reduced non-variable shear strength, whereas samples with iron oxide + kaolinite had an overall higher shear strength but with a greater variance. It is inferred that the reduced shear strength in the white mica samples is due to the sheet (or plate) like structure of the mineral, giving it a weak stress plane. Confidence in the trends observed can be reinforced by expanding the data set in future works. The investigation also includes a discussion on weathering grade and addresses the question as to whether mineralogy abundances influence these characteristics in Hamersley shales.CITATION:Maldonado, A, Mercer, K G and Robert, A, 2017. The relationship between mineralogy and shear strength of Pilbara Hamersley Group shales across the weathering spectrum, in Proceedings Iron Ore 2017, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

ON mineral lease 38 of the Sulphide Corporation Limited, Broken Hill, a shaft was sunk in the early days Ior prospecting purposes and at the present time it is accessible as far as the 1000-ft. level where a connexion exists with the main workings of the Corporation's Central Mine, mineral lease 9. About the year 1895· a crosscut was driven east from this shaft at the 1330-ft. level cutting the Central Ore-body in mineral lease 9 and the shaft is supposed to extend a further depth of 25 ft; but no records of any of this work are in existence, the whole of the evidence being based on hearsay and memory:Fig. 1 shows the position of the Extended shaft in relation to the main workings. The shaft filled with water to the 1000-ft. level where it overflowed through the crosscut to the main shaft and was pumped to the surface, but when the South drive on the 1300-ft. level was pushed to the southern boundary, it was deemed advisable for safety, to tap the water at this level and so relieve the...

Jan 1, 1919

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

A particle-bubble collision model was used to investigate the minimum recovery zone height, H(r,min) required for flotation columns. The criterion used to define H(r,min) is that height which gives unit collision probability. It is shown that H(r,min) is determined by particle and bubble size, gas hold-up and bubble-bubble interaction. Under typical operating conditions, for flotation of particles less that 10 micrometres in size H(r,min) is greater than 10 m, but it reduces to less than 1 m for particles greater than 100 micrometres

Aug 1, 1995

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ALLEN, Roy H., Capt., Air Service, Bureau of Aircraft Production, Washington, D. C. *AMIDON, CLAUDE E., Chemical Warfare Section', Astoria, L. I. *ARCHBALD, HUGH, 311th Infantry, 78th Division, American E. F. ASKIN, THOMAS B. H., Radio Station, Cavite, P. I. *AYER, FRANK A., Lieut., Commanding Officer, -270th Aero Squadron, American E. F. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., Washington, D. C. *BARRETT, LESLIE P., 1st Lieut., 5th Field Artillery, American E. F. BLICKENSDERFER, F. C., 1st Lieut., N. A., Ordnance Dept., Edgewood Arsenal, Edgewood, Md. *BROOKS, FLOYD R.., Lieut., Canadian Engineers, Seaford, England. BROWN, GEORGE M., Co. G, 1st Replacement Regiment, Washington Barracks, D. C. *BRUNEL, LOUIS J., Lieut., 5th Field Artillery, Brigade Headquarters, American E. F. *BRUNTON, D. W., Cons. Engr., Naval Consulting Board, Washington, D. C.

Jan 11, 1918

ALABAMA Anniston. Carrington, F. G. Ashland.-Herr, I. Auburn.-Brown, R. L. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Salmon, H. S. Schaber, C. F. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Ball, E. M. Bonnyman, J. Bowron, J. Bush, M. W. Crawford, G. G. Crockard, F. H.

Jan 1, 1917

By Andrea Koschinsky, Akira Usui, Michael Bau, Katja Schmidt, James Hein, Thomas Kuhn

Marine ferro-manganese (Fe-Mn) crusts and nodules are metal-rich chemical sediments that are archives of paleoceanographic proxies and potential metal resources and targets of deep-sea mining. Traditionally, crusts and nodules are subdivided into hydrogenetic, diagenetic, and hydrothermal types. While hydrogenetic Fe-Mn crusts are a potential resource for Co, Te, Pt, and REY, nodules are enriched in Cu, Ni, Mo, and Li, and hydrothermal deposits may be enriched in individual metals such as Mo, Ba, and Li, depending on the temperature and composition of the hydrothermal fluid. The different types of marine oxidic Fe-Mn precipitates, therefore, have different economic potential. Hence, a robust classification is not only helpful in the general geochemical characterization of such precipitates (and as such is a useful teaching tool, for example), but may also simplify the evaluation of their importance as a potential metal resource, which helps to prioritize exploration targets for deep-sea mining.

Sep 1, 2014

A study was made of zircon powders bonded with phosphoric acid or aluminium orthophosphate. The influence of strength of solution of the phosphatic binders on the modulus of rupture over a temperature range was investigated. Physical properties of three grades of zircon powder bonded with phosphatic binders were studied at various temperatures. Examination of x-ray diffraction data indicated that phosphates ofzirconia are preferentially formed to phosphates of silica. However, zircon in the presence of excess phosphoric acid also forms phosphates of silica upon heating.Resistance to attack by slags from blast and open hearth furnaces was determined on phosphate-bonded zircon mortars in a cup test with industrially made ladle bricks. Zircon powders bonded with phosphates proved to have high P.C.E. values. The first satisfactory results of a plant trial with phosphate-bonded zircon mortar, used in a steel ladle, are now being assessed in larger scale industrial tests prior to accepting the mortar as a steel plant refractory.

Jan 1, 1972

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

The suitability of char from Yallourn brown coal as a filler for carbon electrodes used in the aluminium smelting industry has been assessed on the basis of the specifications usually laid down by electrode manufacturers for petroleum coke fillers. The purity specifications can be met by a simple acid leaching of the coal before carbonization. The true density of char produced at 1200°C is within 5 per cent of the specification figure, but the bulk density of char obtained from as-mined coal is only half that specified for petroleum coke.Although this can be increased to three-quarters of the specified figure by briquetting the coal before carbonization, further increases would be very difficult to achieve, as the remaining shortfall in density is due to an extensive microporosity developed in the particles of char during carbonization.

Jan 1, 1970

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By R. N. Zitter

PRESENT work was done in connection with a program for obtaining a low energy gap semiconductor suitable for photodetection. The inter-metallic compound InSb, which is now being in-

Jan 1, 1959

By Dennis W. Boehm

The building boom of the late 1970's and early 1980's has all but used up most of the better sites across the more populated metropolitan areas of the United States. This means that current buildings and other types of structures are being founded on more marginal sites. The use of marginal sites has placed ever-increasing quality control on the installation of the deep foundation systems utilized for these sites. Several remedial techniques are available for the repair of the deep foundation systems. These include minipiles, compaction grouting and jet grouting. Eight case histories are cited where these methods have been utilized to repair deep foundations.

Jan 1, 1999

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

By C G. Ryan, T P. Mernagh, S R. Hunns, R A. Both, R R. Large, J B. Gemmell

 The Hellyer and Mt. Chalmers deposits are mound-style volcanic-hosted massive sulphide (VHMS) deposits in Australia. Textural, petrographic and microthennometric investigations of fluid inclusions in the Hellyer stringer system indicate that Type I, primary, liquid-vapour inclusions are 10 - 15 J.UIl in size, and yield homogenisation temperatures of 170 - 220¦C in early 2A veins, 165 - 322¦C in main-stage 2B veins and 190 - 256¦C in late-stage 2C veins. These data suggest a waxing and waning thermal history. However, the average salinity remained between 8 - 11 NaCl equiv. wt % in all Stage 2 veins. At Mt Chalmers, Type I inclusions up to 20 urn are found in quartz from the mineralised zone, and these inclusions yielded homogenisation temperatures of 160 - 268¦C and salinities of 5 - 8 NaCl equiv. wt %. Laser Raman spectroscopic (LRS) analysis indicates the presence of CO2 (<1 mole %) in the Hellyer and Mt. Chalmers VHMS systems. Semi-quantitative SEM/WDS microprobe analyses of fluid inclusion decrepitates indicate that the Hellyer and Mt Chalmers ore fluids were enriched in potassium and calcium but depleted in magnesium relative to seawater. PIXE microanalysis of fluid inclusions in quartz also indicates a significant base metal concentration in these fluids. Cation composition and higher salinities relative to seawater suggest that recycled seawater alone cannot be the sole source of the ore fluids. High base metal content and the presence of CO2 in the fluid inclusions imply that magmatic input of ore metals during seawater leaching of the footwall volcanic pile is a distinct possibility.

Jan 1, 1995

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008