Search Documents

By J. Davis, M. G. Reading

"INTRODUCTIONInternational Minerals and Chemical Corporation (Canada) Limited operates two potash mine/refinery complexes near Esterhazy, Saskatchewan. Annual production of approximately 4.2 million tons is sold in the United States and overseas in five grades according to size and quality.Ore grading 25% K2 0 equivalent is mined from a horizontal bed by continuous boring machines, crushed, and hoisted at 8 inches. The refinery operation consists of the eight basic steps shown in Figure 1. Particle sizes handled are similar to those experienced in other forms of mineral beneficiation: 8 inches to 100 mesh. The ore is crystalline and particles are angular. Fortunately the major mineral constituents, sylvite (KCl) and halite (NaCl), demonstrate relatively low hardness at 2 to 2.5.Therefore, while simple abrasion must be acknowledged, it is not a major problem except, of course, in circuits carrying magnetite.Corrosion, as represented by the classic equations of Figure 2, occurs in all its various forms."

Jan 1, 1983

In a previous paper the author showed that silver considerably delayed the recrystallisation of lead after cold work. The effect of antimony on the rate of recrystallisation of distorted lead was studied next, and the experiments performed, and the results obtained, are described in this paper. Electrolytic lead was used as a standard of comparison.It was also used to make the lead antimony alloys.This electrolytic lead contained 0.0005% total impurities.It was prepared from commercial lead by fire refining, followed by electrolysis and finally by vacuum casting. The process was described in the previous paper and the description need not be repeated here. PREPARATION OF LEAD - ANTIMONY ALLOYS.The steps taken to procure pure antimony are outlined in the appendix. To make the lead antimony alloys a mother alloy was prepared thus:-A quantity of the antimony (it was received in the powdered form) was placed in a pyrex glass tube, which was closed at one end. The antimony was washed with hot hydrochloric acid (1: 1), then with more dilute acid, then with distilled water, and finally with absolute alcohol; it was dried by warming and evacu,ating the tube. This should leave the antimony more nearly free from surface oxides.The amount of antimony was determined by weighing quickly; the appropriate amount of vacuum-cast electrolytic *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

Treatment of Gold-Bearing Oxide High-Clayish Ores The analysis of modern state of treatment technologies of gold-bearing oxide high-clayish ores showed that the main method applied both in Russia and abroad is sorption leaching and heap leaching with preliminary granulating. The use of any of these processes depends on many factors including average gold grade, site and area of a deposit, clay content and etc. The two processes are often used at the same deposit. In this case, rich ores are treated according to a plant technology, poor ores and ores with cut-off grade are treated with heap leaching. Both technologies possess their own advantages and disadvantages. A plant technology is characterised by high recovery with higher capital and operating costs at the same time. Lower recovery during heap leaching can be attributed to an unstable quality of ore granulating due to both technological and weather conditions. In case of poor high-clayish ores, the use of a combined ore treatment is possible and profitable. It includes the ore disintegration and a clayish fraction treatment by using a heap leaching. In this case, capital and operating costs reduce in comparison with a plant technology and the recovery increases in comparison with heap leaching. Sometimes it reaches a plant recovery. These ores possess special features. As a rule, gold is associated with ore fraction, so it liberates readily from the association with ore ore-forming minerals even with relatively coarse grinding explain their high solution velocity in a hydrometallurgical cycle. Clayish ores are characterised by high sorption activity to gold cyanide complexes as well as extremely low velocity of filtration and thickening of slimic pulps at the same time. The paper describes the options of oxidised high-clayish ores treatment, such as, a plant technology (PIP and CIP process), heap leaching and a combined technology (disintegration, heap leaching of a crystalline fraction and sorption cyanidation). The obtained results were used when selecting a treatment technology and during construction of a plant for oxidised high-clayish ores treatment.

Sep 13, 2010

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By C Vuillier, A Roshdieh

Water is the main medium for removing impurities from iron ore during wet processing to achieve a higher quality product. However, there is a substantial increase in freshwater consumption due to an increase in demand from the following two factors: in the past 55 years the world population has doubled from 3 to 7.5 billion and crude steel production has increased five times from approximately 350 to 1662 Mt/a (IISI, 2008). Furthermore, social development in developing countries exacerbates water consumption making freshwater an increasingly valuable resource with an average distribution of 70 per cent for agriculture, 20 per cent for industry and only ten per cent for domestic consumption (Hourtolle, 2005; OECD, 2009). Rapidly changing regulations over the access and preservation of water across the world indicates the growing importance of this issue, so the mining industry must adapt to this continual change and must be committed to increasing the efficiency of water usage.Tailings dams receive most of the water used by the process plant. In arid regions where evaporation is high and availability of water low or non-existent, technical solutions other than the conventional tailings dam, such as thickened and/or filtered tailings, exist to optimise the recovery of water and reduce the need for external water consumption. However, these solutions present additional challenges, such as energy consumption and transportation from the process plant to the ultimate storage area.This paper considers a range of alternatives covering thickening and filtering, transportation and storage, water return, closure and rehabilitation. Mining projects in the future will be more affected by the rising cost in water and tighter regulations in accessing water and energy. Good tailings management can contribute significantly to reducing the dependence on these two key commodities (water and electricity), improving the resilience of iron ore projects especially in arid regions and areas with high competition for water.CITATION:Vuillier, C and A Roshdieh, A, 2017. Minimising the water loss associated with mine tailings disposal, in Proceedings Iron Ore 2017, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Peter Chou

A total of 117 slope stabilization drilled piers were installed as part of a major hillside revitalization project. The 110-million dollar development, known as Stratford at Kenwood, included an 18-story upscale senior residential tower, a 3-story healthcare building, and 4-story condominium buildings, offering approximately 580,000 square feet of living space with panoramic views of Downtown Cincinnati, Ohio. In an effort to establish a flatter hillside plateau for the new 4-story condominium and to create a cut and fill balanced jobsite environment, an 800-foot long row of drilled piers and a 600-foot long multi-tiered shear key system was used to terrace existing 1.5H to 3H: 1V steep slopes and support the new fill. These slope stabilization features reduced the amount of spoils needed to be wasted off-site and mitigated the risk of slope instability. An ODOT/FHWA research indicated that spacing of stabilization piers and necessity of top-connecting elements are highly dependent on pier diameter, spacing, soil type, depth to potential failure surface, surcharge loads, and pier deflection. Due to pre-existing deep buried swales, various load combinations, and the complex mechanism of soil arching effects between adjacent piers, both analytical and numerical computer modeling was performed to estimate the loading on each pier. New generation multiplexed, 3-Dimensional, Micro-Electro-Mechanical-System based inclinometers were installed between selected piers to confirm the pier design, and monitor the fill placement, as well as long-term slope stability.

Jan 1, 2009

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By Blanchard R

In stopes of the 2000- and 2150-ft. levels in the North mine section of North Broken Hill Limited, whence a substantial proportion of the company's production is being drawn, and especially in stopes which involve the portion known as the Northern orebody, occurs it light-coloured friable porous material which represents average grade ore from which the lead and zinc minerals, and certain gangue constituents, have been largely or wholly removed by leaching. The 2000- and 2150-ft. levels lie, respectively, 1550 and 1700 ft. below extreme base of the pre-mine oxidized zone. Composition of the cellular product shows it to be supergene. The oxidation and leaching, therefore, must be assumed to have taken place since drainage of the affected areas was accomplished by mining operations.The matter is of more than passing interest, because the post-mine...

Jan 1, 1942

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By W G. Rowley

The Fortescue Metals Group story began in 2003 with a vision to establish an infrastructure project that would connect the stranded iron ore deposits of the Pilbara region of Western Australia with the steel mills of Asia. Following exploration successes in the Chichester Ranges using their new exploration model, Fortescue established significant iron ore resources at Cloudbreak and Christmas Creek during 2004 and 2005. By May 2006 the definitive feasibility study for mine, rail and port was completed, many of the key government approvals had been obtained, product development and market acceptance were complete and 1.07 Bt of total proved plus probable iron ore reserves were defined to support a 20 year mine life from the Cloudbreak and Christmas Creek deposits. Project construction commenced in September 2006 following a successful $3.2 billion capital raising. By April 2008, the mine and processing plant at Cloudbreak were completed along with the Herb Elliott port facility at Port Hedland and 256 km of heavy haul railroad linking the mine with the port. Mining of overburden commenced at Cloudbreak in late 2007 and by 15 May 2008 the first shipment of iron ore had departed for China. In the first 12 months of operation total shipments amounted to 24.6 M wet metric tonnes with weighted mean composition of 58.9 per cent Fe (64.4 per cent Fe calcined), 4.3 per cent SiO2, 2.0 per cent Al2O3 and 0.047 per cent P. Exactly 3.5 years between the Cloudbreak discovery hole and commercial production. The project success depended on many technical breakthroughs including a new exploration model, application of the surface miner as the main mining production unit, design of a new marketable fines product called æRocket FinesÆ, a highly efficient ædesandÆ flow sheet for upgrading of 2.4 per cent alumina run-of-mine to 1.9 per cent alumina Rocket Fines, 40 t axle loads for the heavy haul railway and a high capacity-highly automated port facility.

Jan 1, 2009

By Larkin F, Farrer E, McGhie R. R

The Electrolytic Zinc Company of Australasia Limited commenced productive operations during February, 1936, at the- Rosebery and Hercules mines, which are situated near Rosebery, Tasmania. At this time it was decided that before re-organizing the steel sharpening shop a test should be made of the relative merits of conventional drill-steel and detachable bits. For this purpose Ingersoll-Rand type"I" thread centre hole.jackbits were selected and seventy-two of these were tested against conventional steel. Results indicated that, under the conditions pertaining at these mines, j ackbits should prove more economical than conventional drill-steel bits, and that a large-scale test, under working conditions, should be made. This was done by gradually replacing conventional drill-steel with jackbits at the Rosebery mine. Results were satisfactory and by the end of 1936 both mines were using only the jackbits.

Jan 1, 1939

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004