Search Documents

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By Carl Beal

THE most important factors that should be given consideration in valuation of oil land are: (1) the amount of oil the property will produce; (2) the amount of money this oil will bring (based upon the future prices of oil) ; (3) development and production costs; (4) the rate of interest on the investment; (5) the retirement or amortization of invested capital; and (6) the salvage or "scrap" value of the equipment when the property is exhausted. These factors are of varying importance, and some of them may not enter all valuation problems, but most of them should be given consideration in any valuation even though only a rough estimate of the value of the property is desired. The value of a property may be changed over-night by the completion of important test wells, by the sudden water flooding, or by a change in the price of oil. The best a petroleum engineer can give is the value of the property under the conditions existing at the time the appraisal is made with a fair forecast of future action of the wells and of the price of oil. Our experience in the scientific valuation of oil lands is not broad and there is very little published information on the subject; it, therefore, becomes necessary in studying such problems to form comparisons with the factors involved in the valuation of mines-the closest parallel. One of the reasons for the lack of substantial progress in oil-land valuation methods has been the necessity of making an estimate of the future production of the oil property to be valued. Oil men and accountants have not generally conceded that such estimates could be made with any degree of accuracy. It has been shown, however, in several recent publications that with certain data available reasonably close estimates can be made. The accuracy of an appraisal depends chiefly on the accuracy of the estimates of future production and of the future price of oil. The accuracy of the former is sometimes necessarily based on geological inferences. Geology is not an exact science and geological data in connection with oil production cannot always be mathematically evaluated.

Jan 9, 1919

By G. M. Swinkels

Sherritt Gordon and Cominco, with financial assistance from the Canadian Government through PAIT, have developed a hydrometallurgical process for refining copper from sulphide concentrates. The main objective of the project was to develop a process applicable to a wide range of concentrates with respect to copper content, other metals content and impurities, within the economic parameters set by present smelting and refining practice. Other important objectives were to recover sulphur in its elemental form and not as sulphur dioxide to assure improved hygienic conditions and a negligible impact on the environment. For the most abundant and relatively refractory chalcopyrite concentrates, the first step of the process is thermal activation with hydrogen to decompose chalcopyrite and pyrite, commonly associated with it, into more reactive sulphides more amenable to leaching. The iron is then selectively extracted by sulphuric acid leaching and subsequently rejected as jarosite. High-bornite concentrates do not require thermal activation and acid leaching; they are subjected to another hydrometallurgical iron removal step. The high-grade copper sulphide resulting from iron removal, and containing all of the initial precious metals, is then leached under oxygen pressure to produce elemental sulphur and copper sulphate solution . After suitable solution purification, the copper is recovered by high-current-density electrowinning as wire-grade product. Precious metals remain in the leach residue and are recovered after separation of the gangue materials and elemental sulphur. The laboratory and pre-piloting test work had indicated copper and precious metals recoveries comparable to those achieved in current practice. The process was shown to be suitable for handling relatively low-grade concentrates and, in addition, it was capable of high recoveries of associated zinc, molybdenum, nickel and cobalt in saleable form.

Jan 1, 1978

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By F. B. Brost

In 1976, a decision was made by Anamax Mining Company to install an unusual conveying system to transport ore 10.3 km (6.4 mi) from the new Eisenhower Mine to the Twin Buttes concentrator. The system, supplied by Cable Belt Limited of the United Kingdom, represents a radical departure from conventional belt conveyors. The driving tension is applied through two endless wire ropes driven by a single 2 240 kw (3 000 HP) drive while the belt acts only as the ore carrying medium. Full production was begun in January, 1979. Start-up problems hampered production for several months but were resolved by a joint Anamax-Cable Belt effort. The system has been operating at design capacity for 4-1/2 years, and has proven itself as a reliable, low cost ore transportation system.

Jan 1, 1984

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By Ricky Chipka, Roshan Thapa, Richard Yovichin, Greg Rogoff, Patrick Niemuth

A 4.5-mile-long, 96-inch-diameter outfall pipeline was constructed between North Texas Municipal Water District’s proposed Sister Grove Regional Water Resource Recovery Facility and the Stiff Creek Discharge Structure. Two TBM-mined tunnel segments were excavated for the outfall pipeline through rock and mixed-face conditions within the Austin Chalk Formation. The TBM mining performance was tracked in detail and evaluated during mining. This paper discusses the TBM configuration, TBM utilization, advance rates, and challenges of both tunnel segments.

Jun 13, 2023

By J. Y. Liu

The comminution in a high-pressure roller mill is modeled by an energy-based population balance approach considering three aspects of breakage taking place in the active zones of the mill: the interparticle breakage in the high-compression zone, the breakage at the edges of the rolls, and the pre-breakage in the acceleration zone. Together with an appropriate model of classification, this model can be used to simulate steady-state performance of closed-circuit grindings with high-pressure roller mill. After a brief description of the basic modeling approach, the algorithm of the steady-state calculation for a generalized grinding-classification circuit is presented, from which the circuit configurations commonly met in industrial practice can be derived. With an iron ore as feed material for example, simulation results are shown and discussed in respect of circulating load, specific energy consumption and product fineness for closed-circuit grindings under various operating conditions. The effects of stressing intensity, working gap, classifier parameters as well as circuit configuration on the overall circuit performance are investigated systematically by means of computer simulation.

Jan 1, 2014

In preparation for the 119th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS Chairman. NY. S. DICKSON, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. P. G. SPILSBURY. H. C. PARMELEE. FOREST RUTHERFORD. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE. FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP Committee on Patriotic Meeting H. C. PARMELEE, Chairman.

Jan 11, 1918

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By P. E. Davidson

The management of solid waste is known to be a large and increasing problem in high-population areas throughout the world. It is not necessary here to add further definition to the nature and magnitude of the problem. Instead, it is the purpose of this paper to describe a new process, called the Andco-Torrax System, which will be of use in converting municipal solid waste into useful energy forms and a granulated slag by-product. The paper includes a description of the first commercial plant for the process.

Jan 1, 1977

By Donald L. Siebert

This profile study of the commercial secondary aluminum industry examines not only the elements that form the industry but also the technological contributions of each toward industrial growth. Concise descriptions of processing methods trace aluminum scrap from generating sources to marketable industrial and consumer goods. Economic and marketing appraisals are used to illustrate the impact that recent technology has had upon the secondary aluminum industry. Price, supply, demand, competition, and substitutes are selected as components of an economic model of the secondary industry and are used to illustrate the aggregate effects of technological changes. The final section is a conceptual look at the future in which sensitive economic indicators (such as die casting in the automotive and appliance industries) are examined as well as the problems of conserving mineral resources by retrieving secondary aluminum from solid waste.

Jan 1, 1970

By A. Mosqueda Martinez, L. C. Trytten, R. P. Kofluk, J. J. Budac

The Corefco ammonia leach nickel refinery treats Ni-Co mixed sulphides from the high-pressure acid leaching of Moa Bay nickel laterite. Due to the low iron content of the feed, the ammonia leach process generates a leach residue with ~10% Ni+Co. Since commissioning a leach residue pressure filtration circuit in 2002, this residue has been stockpiled, dried, and sold commercially. For several years, the residue was sold to nickel smelters overseas. In 2014, re-processing of the residue in the high-pressure acid leach was tested. Lab test work was completed showing excellent extraction of the contained nickel and cobalt, and additional beneficial effects in the high-pressure acid leach circuit. A plant test in Moa confirmed the results, and preparation for shipment of the valuable leach residue for re-processing has begun. This paper outlines the test work and results, and some commercial considerations.

Jan 1, 2015

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental, and technical aspects of open-pit mining operations. Factors influencing ore loss and dilution fall into two categories: (i) controllable factors like mine equipment selectivity and blast design and (ii) uncontrollable factors such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls pre-blast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, the study investigates the relationship between spatial entropy, cut-off grades, blast movement, dig-limits optimization model running time, and profit through a number of case studies. The results show that changes in cut-off grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution, and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy.

Nov 28, 2023

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By M. S. Hunter, D. L. Robinson

An extremely fine subgrain structure found in aluminum and aluminum alloys is shown and a method for revealing this structure is described. The appearance and some of the characteristics of this structure are described and the possible significance of subgrain structure in terms of chemical, electrochemical, and metallurgical processes is considered. GRAINS and grain boundaries, which constitute the principal manifestations of the crystalline aggregates known as metals, play such an important part in determining the characteristics and properties of metals and alloys that their nature and behavior have long been of much concern to the met-allographer. Many investigators have speculated on the possible existence of a finer structure within the usual grain structure and, through X-ray diffraction and metallographic techniques, have revealed evidence that such finer structures exist. Among these structures are the mosaic blocks and domains described by Burgers1 and others in their contributions on crystalline structure and the dislocation theory, the small units associated with polygoniza-tion described by Cahn,2 and the intragranular blocks revealed more recently by Lacombe and Beaujard.3 his paper describes some novel methods for clearly revealing a very fine granular substructure within the usual grains of pure aluminum and aluminum alloys. It also compares the characteristics and behavior of this subgrain structure with those of the ordinary grain structure and gives some examples of the manner in which this substructure may influence the characteristics of aluminum alloys. Metallographic investigations of aluminum and its alloys have dealt extensively with the functions and behavior of grains and grain boundaries and have evolved a definite concept of the relation between grain structure, orientation and physical, mechanical, chemical, and electrochemical behavior. During the examination of etched samples, a roughening or mottling of the body of certain grains has occasionally been observed. Such roughening obviously represented differential attack by the etching solution, but its true significance was not at first realized. It is now known that this roughening probably rep- resented a subgrain structure, although the particular etching treatments used were not capable of revealing this subgrain structure clearly. Also, in practically all cases, the subgrains were apparently far too small to be resolved by the light microscope. Recently, a method has been developed for revealing clearly the subgrain structure of most aluminum alloys. This method is somewhat unique in that it eliminates much of the usual tedious mechanical polishing and the attendant danger of a surface layer of flowed metal and at the same time is simple, rapid, and effective. It involves the use of the Alcoa R5 Bright Dip, a patented chemical polishing treatment licensed by Aluminum Co. of America. This treatment produces a bright, highly polished surface at least the equal of any mechanical polish and also etches the subgrain boundaries as well as the ordinary grain boundaries to reveal both the grain and subgrain structure simultaneously. Metallographic specimens to be examined are taken through the customary grinding and polishing operations used for aluminum alloys.' The usual care required in the final polishing operation to prevent a flowed surface layer and to obtain a high polish is not necessary, however, because any flowed layer is eliminated and a high polish is produced by the final immersion in the Alcoa R5 Bright Dip. Depending on alloy type, this dip takes from a few seconds to about 3 min, after which the sample is rinsed well, blown dry, and is ready for examination. The substructure can be revealed by some of the usual metallographic methods such as electropolish-ing or mechanical polishing and etching but no method has been found which is the equal of the new chemical polishing treatment. Mechanical polishing followed by the usual metallographic etching is not entirely satisfactory for revealing this substructure, probably because of the flowed surface layer resulting from the mechanical polish. If the usual etching methods are prolonged sufficiently to remove this layer, the specimen surface becomes quite rough and the substructure is not defined clearly.

Jan 1, 1954

By Rztssell H. Bennett

A SURVEY of the Mesabi Range iron-ore industry demonstrates that a satisfactory degree of technical progress has been achieved in the last fifteen years. This advance has not been made over a uniform front, but, by salients and bays, according to the different initial positions, economic and technical, of the component producing companies. The producers endowed with rich ore have in general, because of natural advantages, progressed more slowly than their neighbors with leaner properties. The advance has been made step by step all along the line -blasting, loading, hauling and concentrating-and without the benefit of radical innovation. There have been, for instance, no such parallel discoveries in iron ore as leaching and flotation in copper. The much lower unit price of iron operates, of course, to bar the application of these and other practices developed for the higher-priced metals. There exists, however, a radically new concentration process whose technology is well worked out and which may become economically operative in the not too distant future; this, as so often happens in engineering advance, because of recent developments in an entirely unrelated field. First, however, let me devote a paragraph or two to the more important economies effected in mining.

Jan 1, 1932