Search Documents

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966

By Ronny J. Sadri

Under contract to the Department of Energy, Fluor Mining & Metals, Inc. and Bonner & Moore Associates developed a group of computer models that can be used to simulate single seam dragline operations. These models have been subsequently modified by Fluor for use in multi-seam dragline mining situations. The single seam model analyzes the digging, spoiling, and walking patterns of draglines to identify possible parameter changes to increase productivity. Parameters such as key-cutting, panel width, digout length, and bench height, etc., are analyzed in this process. The models were tested using data from four operating mines. Field demonstrations were performed to correlate computer optimization results with field data. Productivity was greatly enhanced at one mine site by a change in some of the operating parameters. The multi-seam study has as its objective the development of a broad- based mine planning tool which would be used to identify and quantify the different procedures employed in multi-seam dragline mines to increase their productivity. The major problem identified in multi-seam mining is the sequencing of the different stripping and mining operations. The multi-seam model has the same capabilities as the single seam model. In addition, it models up to four seams with three partings per seam. It allows the operation of several draglines at different levels, and analyzes the effect of ramps, rehandling, and ancillary mining equipment.

Jan 1, 1982

By Robert L. Marovelli

The thermal conductivities of six rocks were measured by the transient line source method over the temperature range of -850 to 1,500° F. Close-fitting ceramic probes were used in 0.065-inch-diameter holes drilled through 5-to 6-inch-thick rock specimens. Taconite, granite, quartzite, and basalt were used in the tests. The method yields absolute data and is applicable to both laboratory and in situ measurements.

Jan 1, 1965

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium, and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. [Table 1] affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak- type brines, produced mainly for lithium. MARKET ATTRIBUTES Some of the important market traits common to industrial minerals used by the chemical industry are: 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities. 8. Purchases are generally by contract of one year or longer term, with spot buying playing only a minor role. 9. Contract prices are usually fixed in short term commitments, but may vary according to assay, with premiums and penalties for content above or below the norm; however, general practice is for specifications to be fixed in the contract with minimums being set for the desired material and maximums for undesired elements. In longer term contracts, prices are often escalated on labor, fuel, and other vendor processing costs. 10. Suppliers of individual commodities to the chemical industry tend to be limited in number and are generally medium- to large-size producers that supply a few major consumers. 11. The bulk of the mineral volume is for basic chemical uses, sulfur suppliers to sulfuric acid producers and fluorspar for hydrofluoric acid producers being typical examples. These basic chemical products then are used for the production of other products. 12. Shortage of a supply of adequate quality leads consumers to seek substitutes. In the case of fluorspar, much work is being done on recovery of fluorine from phosphate rock. Success in the form of fluorosilicic acid and/or hydrofluoric acid production could, in time, affect the hydrofluoric acid chemical industry. 13. Markets tend to be characterized by cycles of shortage followed by oversupply, with attendant wide price fluctuations. 14. Baniers to trade can have an adverse effect on the necessary movement of industrial minerals used by the chemical industry in international trade. Antidumping laws, quotas, and tariffs can disrupt or dislocate normal markets. 15. Chemical industry consumers may back-integrate for security of supply or for favorable economics, sometimes by joint ownership and often with experienced mining partners.

Jan 1, 1994

By O. U. Bradley

The utilization of casing-head gas in the manufacture of casing-head gasoline by both the absorption and the compression method is a most important factor in the conservation of our natural resources. Any industry connected with the oil business, in general, possesses particular attraction for a large number of people not conversant with its basic principles, for the reason that the large fortunes made in the production and utilization of petroleum and its products have been given undue prominence. The general impression of the public that enormous profits are to be realized in the casing-head gas industry with minimum expenditures of both capital and effort has, in a large measure, accounted for the phenomenal expansion of the industry in recent years and, likewise, has resulted in many mistakes and loss of investment funds. It is true that many installations have been very profitable, but such instances are always the result of careful planning, experienced judgment and conservative estimates. The inception and subsequent activity in the manufacture of casing-head gasoline, enabling the business to assume an important position in the petroleum industry, are of comparatively recent origin, as its greatest growth, particularly in Oklahoma, occurred during the years 1917 and 1918. Much information must yet be secured and systematized concerning the methods of manufacture of gasoline from high-yield casing-head gas, and a large field is still open for the application of accumulated experience and good engineering practice in devising better methods of extracting gasoline from casing-head gas of the poorer grades. The absorption process is coming into general use as a most efficient system of treating casing-head gas, and even so-called dry gas. In fact, there is a decided tendency toward the universal adoption of the absorption process as against compression methods. However, a general discussion of the relative merits of these two systems is not, within the scope of this article. A few of the facts that must be given 'consideration in arriving at a fair and impartial estimate of the actual investment value of the casing-head gas business are the quantity of gas available, the quality and

Jan 1, 1921

By R. J. Leary

A small electronic digital computer employing punched cards has been used to facilitate the solution of a variety of problems in Bureau of Mines pyrometallurgical research. In this work the computer has been found to be economical for solving both simple problems that occur repeatedly and those involving complex or iterative calculations. Each of these classes of problems and their respective solutions are described. These small computers can be used effectively by researchers when they work in consultation with a computer specialist. Close team work produces the required solutions in less time, and, oftentimes, in a more useful form. Participation in programming by researchers develops in them a skill for evaluating the suitability of problems for electronic computing.

Jan 1, 1960

By Cheryl Devine, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg

The microbial-mediated recovery of valuable metals locked in mining wastes presents an economical alternative to conventional hydrometallurgical processes. The present study investigated the bioleaching response of a low-grade nickeliferous pyrrhotite tailings (0.6 wt% Ni) and an upgraded pyrrhotite tailings (1 wt% Ni) produced by Vale Base Metals in the Sudbury Basin of Ontario, with the ultimate aim of maximizing Ni recovery. The initial part of the study focused on the bacterial adaptive evolution protocol, by repeatedly sub-culturing an indigenous culture from an acid mine drainage site on 2% (w/v) pyrrhotite tailings. The results showed that the extent of Ni dissolution is positively correlated with microbial activity. Microbial profiling revealed A. ferroxidans to be the dominant member of the microbial consortium. The enriched culture was used for optimizing the growth medium by varying the concentration of essential growth nutrients. Finally, an aerated biotic and abiotic leach of a 10% (w/v) upgraded pyrrhotite tailings with and without pH control, showed a higher recovery of Ni in the pH controlled experiments. These results demonstrate that a high concentration of the oxidant Fe3+ in solution promotes the dissolution of Ni. Furthermore, the sulphide conversion into So was found to be higher in the pH controlled experiments (32%), relative to the experiment without pH control (10%).

Jan 1, 2015

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972

By A. C. Lane

Relations de la profondeur de plissement avec la gravita-tion et la hauteur des montagnes dans les Alpes. Par A. Heim (Zurich) 50me Anniversaire, Livre Jubilaire Soc. Geol. De Belgique, Rome, Fascicule 1, 17 to 28. Measurements show a negative anomaly, less densities of .the material below sea level. The author expresses it in terms of the thickness of rocks of an arbitrary density, 2.4, which might be considered wanting. The accordant heights of the summits, the depths of the folds, the deficiency in .gravity, and denudation he finds to be connected. The Alps float on the lightness of the folds of "sal" of weight 2.6 to 2.75 plunged into the heavier "Sima" according to a for-mula: P = h (2.7/2.8-2.7) where - P is the depth of fold-ing below sea level; 2.7 is the weight of the material accu-mulated in folding; 2.8 is the weight of the material dis-placed by it; and h is the mean height of the mountainous regions. For instance, between the valley of Saar and the Val de Bagne in Valais the depth of the folds according to Ar-gand's profiles is between 30 and 40 kilometers. The loss of gravity has been estimated in this region as 1450 X 2.4 = 3480 in units of weight. Obviously errors in the densities would profoundly affect the estimates of the thickness of folding, but his depths of folds are obtained from sections, and from them he works back to the densities. Of course other densities might be placed in the formula. Zur Dichte bestimmung von Tonen. By J. Koenigsberger, Berg u. Hüttenmannisches Jahrbuch, 75, I. Discusses Dr. B. Wilser's investigations as to the best way of obtaining the weight of rocks per unit volume. The use of mercury for rocks affected by water as there recom-mended may easily give too large volumes unless 1 to 3 atm. pressure is used. Thick machine oil is recommended for large lumps of clay.

Jan 4, 1928

By Harry Perry

In the United States the state mining laws enacted in the late 1800s were the first laws to recognize that an employer had a responsibility to provide the employee a place to work that met at least some minimum safety standards. The coal mining industry was also the first major industry in the United States to be regulated in 1952 by federal safety laws, although federal inspectors had the right-of-entry as early as 1941. Within recent years, however, the Congress has enacted a number of federal safety regulations for a variety of industries, such as the Aviation Act (1958), National Traffic and Motor Vehicle Act (1966), National Gas Pipeline Act (1968), and Radiation Control for Health and Safety Act (1968). The fatality and injury experiences of the mining industry in the United States, while at a significantly higher rate than for industry as a whole, showed a continuous improvement until the last decade or two-at which time the rate leveled off. Although fatality and injury rates in foreign countries have been generally lower than in the United States, further improvement in those countries also has been difficult to achieve in recent years. It appears, therefore, that some major change in mining laws, combined with a radical improvement in mining technology and a more effective labor-management safety program, will be needed if further reductions are to be achieved in fatality and injury rates. At the same time, there is a growing awareness by society that an employee's place of work, where he spends nearly half of his waking hours, should be made as safe as possible. As increased consideration is given to means for achieving greater safety in all industrial situations, it is becoming apparent that more is required than merely providing physical safeguards on tools and machines. Rigorous, strictly enforced safety standards are useful, but more important is the desire of labor and management to make certain that industrial accidents are prevented. The pressure to achieve increased productivity, and thus receive higher wages, can be a significant deterrent to safe working practices. The temptation can be great to "take a chance" or "cut a corner" in order to speed up production. Public concern over all types of industrial safety in the United States was reflected by the introduction of a number of general occupational health and safety bills in Congress for the first time in 1968. While no legislation resulted, the hearings revealed that, although there were differences in how standards should be set and who should administer them, there was agreement on the need for adequate laws. Since the mining industry has been subject to safety standards longer than other industries, it is not surprising that advanced safety concepts for mining are being explored by the industry and the enforcing agencies. More complete and sophisticated accident reporting is being planned that will reveal the

Jan 1, 1976

By Staff

"The Weyburn Oil Field, located 80 miles southeast of Regina, Saskatchewan, was discovered by Central-Del Rio Oils Limited, in January, 1955. As of January 1st, 1959, the field had 357 wells capable of producing an estimated total of 45,100 barrels of oil per day.Highly portable, economical, drilling rigs are used to penetrate the pay at a depth of 4,400 to 5,100 feet. Presently, the complete drilling operation for an average field well, including drilling, coring, testing, and running casing, requires 12 days. Drilling procedures are conventional for a field of this depth and no serious problems exist. Central-Del Rio core the productive section of all their wells, which provides valuable information for well completions and reservoir studies. Production casing procedure is to set through the zone and perforate the productive inter-val. This was found advisable due to the lensing nature of the porosity and permeability throughout the reservoir, and to the high connate water saturation encountered in the tighter sections of the reservoir in the north and northeast areas of the field.Although a few wells in the field have produced naturally by flowing or pumping without acid treatment, it has generally been necessary to acidize the wells to make them commercial producers. To date, acid treatments appear to effect better stimulation of the limestone reservoir than fracturing treatments. Perforation sealing balls have been used as an aid in selectively treating all of the perforated interval.The majority of the field is on pump, producing at a low gas-oil ratio. The main part of the field has water-free production, with most of the water being produced in the north and northeastern area. Salt-water disposal is now available in the field through two disposal wells completed in the Basal Blairmore sand.The Midale Beds ""Marly"" and ""Vuggy"" zones form the principal reservoir, which is a stratigraphic trap, with the north and northeast edges terminated by a porosity and permeability pinch-out and the south-west and west edges bounded by water-laden porosity. There is no evidence to date of a gas cap. The reservoir apparently is producing on a fluid-expansion-type mechanism. The increasing water production in wells on the southwest and west edges of the field indicated water encroachment from these directions, and suggests some recovery energy may be available from this source.The total probable ultimate remaining recoverable reserves have been estimated at° 332,469,000 barrels of oil. Markets have not been able to keep up with the rate of development of the medium crude re-serves. However, it is felt strongly that substantial additional markets for Weyburn medium crude will be developed by the producers in the near future at realistic wellhead prices."

Jan 1, 1959

Six hundred miles inland from Australia's east coast Port of Townsville in Queensland's sea of rock and spinifex lies Mount Isa. The town, as in most mining towns, is dominated by its mine and the mine in turn is dominated by its 503 ft copper smelter stack. This candy and white painted stack is a striking introduction to one of the world's greatest copper producing mines and a town where people of over 40 different nationalities live remote but well. Mount Isa Mines Limited is surging into the ranks of' the world's great mines on the momentum of a relentless push begun in 1956. It is as if the time lost in the lean years of the past should be caught up in a hurry.

Jan 10, 1964

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003

By N. Pessall, A. D. McQuillan

The phase relalionsllips in an isothernzal section of the Ti-Zr-H system at 750°Chave been investigated by measurement of hydrogen equilibrium pressures. The resulting diagram indicates that the hydride phase has an anomalously wide range of homogencity extending from 66.6 to 30 at. pct H in alloys containing about 15 al. pet Zr. Measurement of the heat of solution of hydrogen as a function of alloy composition in ß-phase alloys indicates no anomalous behavior in the region of 15 at. pet Zr, and suggests that the extensive range of homogeneity in the hydride phase at about this composition must he attributed to an enhanced stability of the, hydride phase. THE manner in which titanium and zirconium react with hydrogen and the constitutional diagrams of the two metal-hydrogen systems are qualitatively very similar,'-6 as can be seen from Fig. 1 which shows the constitutional diagrams of the two systems. Quantitatively, however, there are some differences. For example, the exothermic heat of solution of hydrogen in ß titanium is smaller than that in ß zirconium, and consequently the equilibrium hydrogen pressure of a Ti-H alloy is higher than a Zr-H alloy at the same temperature and hydrogen concentration. Other differences manifest themselves in the hydride phases which exist at high hydrogen concentrations. In the Ti-H system, above room temperature, there exists only a single hydride phase in which the metal atoms are arranged on a fee lattice, but in the zirconium system there are two hydrides, and whereas the hydride of lower hydrogen concentration has a fee structure, the higher hydride has a face-centered tetragonal structure. The tetragonal hydride retains its stability up to temperatures in excess of 450oC.7 From the foregoing, it would be expected that the constitutional diagram of the ternary Ti-Zr-H system would have a very simple form, especially as titanium and zirconium are completely miscible in both the a and ß forms.8 The present work, which consists of a study of an isothermal section of the ternary system, was carried out in order to check the assumption frequently made that the electronic structure of the two metals and the mechanism by which hydrogen is held in solution in the metals is the same for each. Although this proved largely to be true, certain inter esting and unexpected features of the ternary system emerged which must be explained before we can really say that the reactions of titanium and zirconium with hydrogen are fully understood. EXPERIMENTAL PROCEDURE The most convenient method of studying hydrogen-metal systems is by the measurement of the hydrogen pressure in equilibrium with the hydrogen dissolved in the metal as a function of hydrogen concentration and temperature. In binary systems, the results are easily interpreted in terms of alloy constitution, since two-phase regions can be recognized by the fact that the hydrogen pressure at constant temperature does not vary with the hydrogen concentration in the alloy when it is in the two-phase condition. This criterion does not apply in ternary systems, but there is usually a marked change of slope in the isothermal pressure-composition curves when a phase boundary is crossed, and with care, and a knowledge of the limiting binary systems, the phase structure of the alloys can usually be deduced. In the

Jan 1, 1962

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By Willian dos Reis Lima, Breno Totti Maia, Guilherme Silva Machado, Adeilson Roberto Ribeiro, Carlos Alberto de Souza, Douglas Augusto Pena, Fabrício da Silveira Garajau, Marcelo de Souza Lima Guerra

Oct 1, 2019

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By Lippe D. Sadwin

A high-speed streak camera method for making equation of state measurements (shock and particle velocities) on samples of rock under dynamic load conditions is described. Experimental data are given for tests on 12 samples representing 5 rock types. Analysis of these data shows that the method is practical and that good reproducibility of results can be obtained. The pressure range covered in the tests was from 1 to 50 kilobars.

Jan 1, 1966

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry's first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005