Search Documents

By H. C. Young

This paper deals with roof bolting in Alabama coal mines and iron-ore mines from the time it was introduced in early May 1948 to May 1, 1953, a 5-year period. The Tennessee Coal & Iron Division of the United States Steel Corp. began systematic roof bolting in early May 1948 in a coal mine and in an iron-ore mine, which had some of the poorest roof conditions in the Alabama mines. After the efficiency of roof bolting had been proved by the Tennessee Co. it was gradually adopted by other companies throughout the State, until in May 1953 approximately 53 percent of Alabama's total coal production and 100 percent of Alabama's total iron-ore production, mined underground, was being produced from roof-bolted areas. Statistics in this report will show the advancement made in roof bolting in the 5 years and also the amount of roof bolting that was being done as of May 1, 1953. Significant progress has been made in the coal and iron-ore mines of Alabama in reducing the roof-fall fatality rates during the past several years by adopting systematic roof bolting. The groundwork was laid through successful experiments early in 1948 by the Tennessee Coal & Iron Division of the United States Steel Corp. in cooperation with the Federal Bureau of Mines. This experimental work was based upon the previous experience of the St. Joseph Lead Co.2/ in its Southeastern Missouri mines.

Jan 1, 1954

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

Teleseismic travel time residuals measured on 600-1000 km seismic arrays across the Rio Grande and East African rifts provide evidence for upper mantle low velocity zones beneath each rift of velocity contrast 6%-8%. Refraction studies show thinning of the crust below the rift axes. Regional uplift which extends hundreds of km either side of the axes, is isostatically compensated by negative density contrast at depth. Since the refraction argues against compensation by thickened crust, compensation in the upper mantle low velocity zones is suggested. Temperature effects alone can not explain the reduced velocities. Generation of a few percent of partial melt is the most probable source of the reduction. A passive extensional mechanism is investigated for the Rio Grande rift in which hot asthenosphere intrudes the lithosphere raising its temperature and generating moderate melting. It requires less than 1% extension to explain the melting but a prodigious 26% to raise the temperature from a pre-rifting continental geotherm to the solidus. Geological estimates find that extension is less than 10% over the uplift zone. Such a mechanism is possible only if the prerifting lower lithosphere geotherm lies closer to the solidus than that of stable continent. This is supported by the observed high heat flow in the Rio Grande rift uplift region which, given the long time constant for thermal diffusion, reflects elevated temperatures at depth well in advance of the onset of rifting.

Jan 1, 1987

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By M. L. Haider

Introduction I Appreciate very much the opportunity of discussing with you tonight oil developments in western Canada. These developments are of importance to all of us, first because of their great economic significance to all of Canada, and second because of the location of the new oilfields. Situated as they are in the west and northwest, they are of considerable strategic value from the standpoint of continental defence. The story of oil development in Canada covers a span of almost a century, during which time success in finding reserves of petroleum was barely sufficient to maintain interest in continuing the search. Finally, in 1947, a well of the first importance was completed in Alberta and, judging by discoveries made since then, it appears that Canada, at long last, is to become an important producer of petroleum.

Jan 1, 1950

By Stewart C. A

The Northparkes copper-gold project is being developed in Central Western New South Wales approximately 30 km NNW of the town of Parkes and approximately 350 km west of Newcastle. The project is a joint venture between North Limited (80 per cent) and the Sumitomo Group (20 per cent). North is the manager. The basis of the project is three copper-gold orebodies, the northern two of which are being mined by conventional open cut methods with the third and largest orebody at the southern end of the lease to be mined by block caving. A fourth mineralised body has been identified in the centre of the lease. While further evaluation of this deposit is required it would appear to be amenable to block caving. Oxide caps of gold ore and copper-gold ore over-lie the two northern orebodies. Development commenced with the construction of a carbon-in-pulp (CIP) plant to treat the oxide gold ore. Construction of a flotation plant to treat oxide copper-gold ore and sulphide copper-gold ore is underway. When full-scale operation is achieved late in 1996 the plant will treat 5.0 million tonnes of ore per year of which 1.1 million tonnes will be open cut ore and 3.9 million tonnes will be block cave ore. In terms of annual ore tonnage the underground mine will be the largest metalliferous mine in New South Wales and the second largest in Australia.

Jan 1, 1995

By Paris V. Brough

This paper, which describes the practice of milling custom ore, in addition to that produced under company and lease operations in the Tom Reed mines, is one of a series 'being prepared by the Bureau of Mines. ACKNOWLEDGMENT Acknowledgment is made to W. B. Phelps, managing director, and Jack Zwinge, superintendent, far permission to publish, a-ad to G. E. Jarpe, the present mill superintendent, for his assistance in preparing the paper. LOCATION The mill is in Oatman, adjacent to the Benjamin Harrison shaft of the Tom Reed Gold Mines Co., in the foothills on the western slope of the Black Mountains, western Mohave County. The railroad shipping point is Kingman, Ariz., 25 miles northeast of Oatman. Paved highway U. S. 66 passes by the mill. The altitude is approximately 2,700 feet.

Jan 1, 1937

By E. Dendy Sloan

An overview of hydrate properties is given, with emphasis on unusual deviations from ice, the most common solid water form. Reliable sample preparation and reproduction of in situ hydrates provide the foundation for all hydrate science and engineering. Relations are given to connect the three domains in the title: (1) micro-scopic properties measured with Raman, NMR, and diffraction spectroscopy, (2) meso-scopic properties measured with single crystals, and (3) macro-scopic properties measured with pressures, temperatures, volumes, etc. A principal illustration relates micro-scopic and macro-scopic domains. Experiments provides the basis for improving statistical thermodynamics model for these compounds. To date, this model is one of the most commonly used industrial statistical thermodynamics applications, based upon the classical model of van der Waals and Platteeuw (1959). Microscopic measurements and simulations indicate model assumption improvements, resulting in the next generation of the statistical thermodynamics for improved macroscopic property prediction.

Jan 1, 2002

By G. T. Lineberry

Power requirements for a piece of mobile mining equipment are largely dependent on the set of conditions in which they must operate. These conditions are isolated and key parameters are identified. The effect of operating conditions on power determination is investigated. A simulation technique is developed to predict ranges of power demands for off-highway haul units as an archetype, permitting the analysis of changeable operating conditions. This program uses given data, conditions, and probabilities and ranges to solve for individual components of power, which can then be summed. By adopting such a technique, a systematic and rational determination of power is made possible. The usefulness of this basic approach in the determination of power requirements for other mobile mining equipment is emphasized.

Jan 1, 1983

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By T. T. Chen

Hydrometallurgical products are difficult to characterize because of their fine grain sizes, heterogeneity, often amorphous structures and water soluble or hydrated constituents. Such products are advantageously studied using complementary mineralogical techniques including >50, ore microscopy, SEM-EDX, electron microprobe analysis, selective leaching and wet chemical analysis to determine the phases and their morphologies, to identify specific element carriers, and to elucidate the chemical reactions occurring during the metallurgical process. Sample preparation is an important consideration for these materials. For extremely fine-grained particles, or soft and brittle products such as elemental sulphur, the study of loose powder mounts provides information not available from the examination of polished sections. To demonstrate the application of the various mineralogical techniques, commercial zinc roaster calcines and leach residues, copper refinery anodes and anode slimes, and laboratory bornite leach residues were examined in detail. The various sample preparation and mineralogical methods are presented, and the use of these complementary and practical mineralogical techniques to improve the understanding of a particular hydrometallurgical system is discussed.

Jan 1, 1989

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By C. S. Gundewar

About 90% of the barytes produced the world over is used for oil and gas drilling as weighting agent in drilling mud to control pressure, prevent blow out and provide lubrication. This is because of its unique properties like high specific gravity, water insolubility and intentness. India is one of the leading producers and exporters of barites. The Mangampeth Baryte deposit in Cuddapah district of Andhra Pradesh, India being the largest single deposit in the world having a reserves of about 80 million tonnes. Approximately 50% of the total reserves of grey barites of Mangampet deposit assays less than 92% BaSO4, the minimum stipulated grade for oil and gas drilling industries. To reach and recover the high grade barite, the overlying low grade has necessarily to be mined out and removed. At present this is being stacked separately at the mine site involving lot of labour and transport cost. Considerable barites is contained in the dumps adversely affecting the conservation and creating lot of environmental hazards. IBM being the premier organization in India in the field of conservation of minerals and environmental protection in mining has recognized the importance of adverse effect of these huge dumps at site. The Ore Dressing Division of IBM, Nagpur has characterized these dumps and developed the flotation process on a sample assaying 66% BaSO4 and 23.3% SiO2. The flotation concentrate obtained assayed 93.7% BaSO4, 2.38% SiO2 with BaSO4 recovery of 80% and meets the requirement of the oil industry. The flotation concentrate being non-wetable, can not be used as such as weighting agent, and hence the collector coating on the concentrate was removed either by acid treatment or heating to make it water wetable. The concentrate was 92% -325 mesh and having a specific gravity 4.3. The barites concentrates so produced meets the size, grade and specific gravity specifications required for use in oil drilling industry. Apart from the financial benefits the process augurs well for the commercial exploitation of these huge dumps in terms of (1) additional recovery of these valuable minerals and conservation, (2) reduction in dumps value, (3) improvement in environment and offering an excellent potential for export.

Jan 1, 2014

By R. Bruce Thorndycraft

Pinson Mining Company was formed to develop a gold orebody located in northern Nevada near Winnemucca. A feasibility study was undertaken in 1979 by a consortium of three Toronto-based mining companies and a Reno-based exploration company. The study indicated a viable project with gold priced above $225 per ounce. A project manager, and mine and mill superintendents, were hired in late 1979 to expedite the development of a 1000 ton per day mine-mill complex. Plant design engineering was contracted with Industrial Design Corporation in Salt Lake City. Three experienced plant metallurgists representing Pinson were stationed in Salt Lake to guide the work of Industrial Design. Among the many design criteria spelled out by Pinson, foremost were bringing the mill on line as quickly as possible at minimum capital cost. Fourteen months after the beginning of design engineering, the completed Pinson mill became operational. Total capital cost, including mine development, was $18 million. The Pinson project has proved to be far more than viable; the entire capital cost will be recovered within 18 months of the mill start-up.

Jan 1, 1982

By M. Soltanieh

The liquidus surface? and tie-lines in the nickel-cobalt-sulphur ternary system have been determined between 1<273-1573 K. The experiments were conducted by equlibrating the liquid sulphide with the metallic alloy phase. The liquid sulphide phase was sampled and chemically analyzed. The alloy was analyzed by electrol} microprobe. Combining the present results with the.avai1abl~ literature data, the thermodynamic properties of this system were calculated.

Jan 1, 1998

By J. E. McConnell

No. 1 Electric Furnace and Billet Casting Shop, located in Plant No. 4 adjacent to our new 12 inch merchant bar mill, represents Inland Steel Company&apos;s first venture into both electric furnace steelmaking and continuous casting. Construction of the shop began in September, 1968 with excavation and foundation work, followed by awarding of general construction and major equipment contracts from December, 1968 to April, 1969. The first heat was tapped from No. 90 furnace on December 18, 1970, and the first cast attempted on December 29, 1970. The rated shop capacity is 500,000 tons per year of semi-finished billets and blooms, and was justified on the basis of approximately 85 percent of the product mix falling into the special bar quality category of steel grades. Auxiliary equipment has been designed into the shop to pursue free machining steels, including leaded and tellurized grades. The start-up and operation of the shop for the first year was essentially based on a two-part philosophy: 1. Initially operate with the "open stream" casting technique to accomplish machine shakedown and operator familiarization and training. 2. Operate with special bar quality, or "submerged casting", practices, make necessary refinements and gain customer acceptance

Jan 1, 1972

By M Pizey, P Lindsay

Coal mining has been occurring on the Stockton Plateau for over 100 years. As a result of both natural conditions and mining activities, surface water on the plateau is known to have low pH and elevated metals concentrations, a condition known as acid rock drainage (ARD). Solid Energy New Zealand Ltd (SENZ), as owners of the current mining operations at Stockton desire to understand the nature and causes of ARD at Stockton to determine whether commercially viable options can be developed to improve the water quality to levels acceptable to the local community and regulators. A series of integrated water quality investigations have been performed towards developing a characterisation of the water quality on the Stockton Plateau and receiving waters. The investigations performed include: design and implementation of a water quality monitoring program to collect a satisfactory base of water quality data from which to develop an understanding of the water quality and its variability, and to collect data regarding the range of flow rates that occur in the principal streams; development of a hydrological model for the Plateau with the ability to predict flow rates at key locations on the plateau and on the Ngakawau River; field investigations of the bio-diversity of the plateau and surrounding areas, to develop a snapshot of the health of aquatic communities and whether streams draining mine workings are æadversely impactedÆ; eco-toxicology; waste dump seepage water quality monitoring at selected basal springs, drilling, investigations and permeability and geochemical testing; data processing of a range of historical data and the newly acquired data for the development of empirical relationships that describe the water chemistry system and its relationship in turn to flow rates in the streams; simulation of the long term water quality record for the measured parameters (pH, acidity and metals concentrations), based on the hydrological model and the empirical relationships developed from the new database; and preliminary development and examination of mitigation options for the ARD issues at the mine. The study has progressed towards design of pilot studies of options for mitigation of the generation of the ARD as well as treatment of the discharges. It is the integrated approach adopted by SENZ from an early time in the investigations, that has enabled fast-tracking of the pilot engineering trials. This paper presents the results of the field investigations and eco-toxicology studies and demonstrates the value of predictive modelling of water quality in the study area, even at a very early stage in the remedial engineering design process.

Jan 1, 2003

The Bureau of Mines human factors research program is directed toward reducing accidents and improving the overall efficiency of the person-machine environment interface found in surface and underground mines. The focus of the hum factors program therefore, is to insure that sound knowledge is available concerning human capabilities and limitations, and that this knowledge is applied to the design, of mining equipment, work tasks, and management procedures. The papers presented in these proceedings summarize some of the recent Bureau research in hum factors. The papers focus on two broad areas, human resource issues and human engineering of equipment, tools, and work procedures found in mines.

Jan 1, 1987