Search Documents

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2,3,4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6,7) and Majima and Takeda (El. These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By H. O. Hofman

Lime-roasting is a term proposed by Ingalls' for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse un-decomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale,—the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent. of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1908

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,',' electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

COMMITTEES Committee on Arrangements DAVID H. BROWNE, Chairman LAWRENCE ADDICKS THOMAS T. READ P. E. BARBOUR BURR A. ROBINSON GEORGE D. BARRON F. T. RUBIDGE KARL EILERS E. MALTBY SHIPP LOUIS D. HUNTOON BRADLEY STOUGHTON H.A. MEGRAW EDWARD B. STURGIS ARTHUR L. WALKER

Jan 4, 1917

Newmont Australia Limited has for some 15 years mined a number of large open cuts associated with the Telfer Gold Dome deposits. The principal ore body exploited has been the East Flank of the Main Dome where a very high grade gold reef deposit of mixed metal sulphides, grades in excess of 20gA Au, has been mined in conjunction with dissemi- nated mineralisation contained in the overburden material. The main ore body has been under review for some years as an under- ground mine, however due to the ore body widths of less than 1 metre and a dip generally less than 35 degrees and a very weak host rocks earlier studies all resulted in a continuation of open pit mining activities. In early 1988 it was recognised that open cast mining would not be able to mine all of this valuable resource and a feasibility study was commenced to come up with a practical and economic approach to underground mining.

Jan 1, 1991

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

Conventional logging tools such as density, neutron, and acoustic have ranges of investigation of tens of centimeters. The borehole gravimeter, however, has a range up to hundreds of meters. For example, from the center of a cylindrical ore body 0.20 g/cm3 denser than its surroundings, one can detect the boundary of the ore body at a radius as large as five times its height. More complex structures can be investigated with computer programs. We can predict the usefulness of proposed gravity surveys, or decide which suggested structure is most likely to have caused the results of existing surveys.

Jan 1, 1988

By V. N. Medvedev, A. M. Bryukhanov

Stationary mine air control equipment enables monitoring of CH4 concentration only in sensor locations. CMC-4 individual indicator built into a caplight has been developed in Ukraine, extending CH4 monitoring to manned job sites. Major technical characteristics of the indicator are demonstrated. It features two operation thresholds: 1st threshold 1.0 to 2.0% vol. 2nd threshold 1.5 to 2.5% vol. Basic absolute accuracy ± 0.2% Caplight battery is a common power supply for the lamp and CH4 indicator, providing at least 10 hours of the system non-stop operation. Average pre-failure life is at least 10,000 hrs. It features: an explosion proof design and intrinsically safe test circuit; a small-sized sensor as an integral part of the caplight; a hybrid microcircuit to facilitate functioning of methane monitoring unit. The CMC-4 indicator weight is the weight of the caplight itself and equals 2.4 kg. A two-threshold design makes possible to distinguish between methane sources: slow accumulation due to diffusion or sudden rushes due to a gas-dynamic event. CMC-4 indicators in addition to stationary equipment minimize the risk of CH4 explosion underground determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By R. A. Meussner, R. T. DeHoff, F. N. Rhines

ZINC diffuses through copper more rapidly than does tin. Accordingly, when a ternary diffusion couple is made, by bringing an 0 copper-zinc brass into contact with an a copper-tin bronze at fixed high temperature, it is to be expected that zinc will diffuse into the bronze faster than tin diffuses into the brass. Adjacent to the brass side of the couple the total alloy content (zinc plus tin) should diminish, therefore, while next to the bronze side the alloy content should increase. Since the path of compo- sition change must be continuous, in a single-phased alloy, it should follow a curved and, in general, an S-shaped course. The realization of this prediction is demonstrated in Fig. 1, where the composition paths of two ternary diffusion couples are plotted on the appropriate isotherm of the copper-tin-zinc phase diagram. The diffusion couples were both made from a binary copper-tin alloy analyzing 5.0 pct tin placed against binary copper-zinc alloys analyzing 18.9 and 29.3 pct Zn, respectively. These alloys were produced from electrolytic grades of copper and zinc and a pure grade of straits tin, melted under borax in clay-graphite crucibles and cast in a vertical iron mold. Cylindrical pieces 1 in. in diam and 1 % in. long were machined from the casting and were faced by metallographic polishing to good matching end surfaces. Pairs of the cylindrical pieces were held

Jan 1, 1959

By Otto Rellensmann, Eugene P. Pfleider

For many years mine surveyors and exploration engineers have sought an accurate means of transferring meridian underground by using the gyro-compass. These efforts have generally failed, either because they were inaccurate or because the size and cost of the unit were prohibitive. During the past ten years, however, great strides have been made. Autonetics in California has developed a comparatively light-weight (100-lb) gyro-theodolite, and the Institute for Mine Surveying at Clausthal Mining Academy in Germany has developed an instrument that is accurate to within 20" to 30" of arc. Concurrently, Minneapolis-Honeywell has produced an astounding gyro, the size of a salt shaker, that weighs less than 0.5 lb and compares favorably in performance with the 50-lb gyros of conventional design. This unit, designed for missile guidance, should be adaptable for surveying small boreholes. Given the proper interest and approach from the engineering fraternity, excellent gyro- compasses could probably be available for accurate underground survey work at nominal cost within the next three years. Principles of the Gyro-Compass: The gyro- compass, used for 50 years as a navigational instrument in ships and aircraft, senses the turning axis of the earth and points out true polar north. It does this by employing the earth's rotation, the force of gravity, and the precession characteristics of a gyro. For further details the reader is referred to several excellent publications1-3 covering the principles and application of the gyroscope.

Jan 5, 1959

By L. G. Austin

INTRODUCTION Autogenous (including semi-autogenous) grinding has probably been the most important single innovation in milling practice for the last twenty years. However, the design of these units has been largely a matter of trial-and-error, since the normal empirical laws for the design of ball mill circuits do not apply with exactitude to autogenous grinding circuits. There have been examples of autogenous mills failing to achieve output or product specifications. It is worthwhile, therefore, to attempt to develop a more detailed and precise set of design laws, using the concepts of specific rates of breakages and daughter fragment distributions (1), and performing mill simulations by computer. This type of approach has been applied to ball and rod milling (2, 3,4,5), but even for these mills it is by no means complete as yet (6), because of the amount of experimental work involved. There has not been a strong incentive for industry to develop new design procedures in ball and rod milling because the prior back-log of experience with these mills makes for easy design by empirical comparsion with existing systems. The new approach has been followed mainly by University groups (7,8,9,10), although experience in Australia (9,11) has shown the advantages of the approach. Stanley (12) has applied the approach to results from a large autogenous mill, and we will use many similar concepts to his work, but extend the concepts to a more

Jan 1, 1977

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

By Caelli T, Robey M

Most research into planning of open pit mines has been based on evaluation of volume-element block models in terms of their net present value. The major issues revolve around two interdependent problems the optimum ultimate pit and time-based scheduling. Despite feedback between the two problems, they are usually treated as separate tasks.The ultimate open pit is defined by the removal of whole blocks so that their net present value is maximised. This gives planners an estimate of the total worth of the venture in present terms, and is crucial to obtaining funding. All cost and profit values are assumed to be static throughout the mine life, and the only physical constraint usually taken into account is that of safe, average, wall slopes, which must be approximated by the removal of whole blocks. Modelling of any further constraints (for example, access roads and true wall slopes) is usually achieved by adding them to the optimal pit by hand. Typically this degrades the model by between five and 20 per cent of its value - which then brings into question whether it is still the true optimum.This paper reviews the dominant methods in use for this first task the ultimate open-pit planning problem. Some new optimisations are given, and the algorithms are examined in terms of their efficiency and accuracy. Finally, suggestions are made for improvement of model accuracy and eventual expansion into solutions of the more complete dual problem - that of simultaneously finding the optimum ultimate pits and dynamic schedules for the venture.

Jan 1, 1996

The treatment plant of the Gold Mines of Kalgoorlie Ltd. is situated on the Oroya South Lease, on the Eastern edge of the Kalgoorlie Golden Mile.It was designed and erected by Messrs. Alex. Stewart and Company, in consultation with Mr. Harry Hey, and was completed in November, 1937.Its original capacity was 9,000 tons of all-sulphide ore per calendar month, l?ut the plant was extended in October, 1939, to treat 13,000 to 14,000 tons per month of mixed sulphide and oxidised ore.Recovery of the gold is accomplished by cyanide treatment, followed by flotation of the cyanided residue, roasting and cyanidation of flotation concentrate and precipitation of the gold from the cyanide solutions. In the cyanide section, the crushed ore is finely ground in cyanide ,solution and the pulp is agitated to dissolve further gold. It is then thickened and filtered. In the flotation section, this filter residue is conditioned with S02 gas and a pyrite-gold concentrate recovered by flotation.This concentrate is roasted and then cyanided.KALGOORLIE ORE DEPOSIT.The Kalgoorlie ore deposit occurs within a wide area of Pre-Cambrian rocks, ,and consists essentially of two series of basic igneous rocks known as the older greenstone series (calc schist) and the younger greenstone series (quartzdolerite- greenstone) . The older greenstone is a group of lava flows. The younger intrusive greenstone series can, in the main, be classified as a chloritised and carbonated...

Jan 1, 1948

By John E. Good

A new coal boom is under way in western Canada. As recently as the mid-1960's, the coal industry in western Canada was considered stagnant and, by some people, dying. But Japan's growing need for coking coal, which became more pronounced in 1966, sparked great interest in western Canadian reserves.' As a result of a rapidly expanding export market and growth in domestic demand, Canadian coal production spurted to 16.6 million tons in 1970. Production in 1965 was 11.5 million tons. Today, about 60 percent of Canada's output comes from western Canada, but by 1975, 87 percent (23.1 million tons) is expected to come from this area, and 96 percent (68.3 million tons) by 1990. Opening, developing and operating new coal mines to meet the needs of a rapidly expanding market for western Canadian metallurgical coals pose some unique and difficult problems. Covering nearly every aspect of opening properties in remote areas, the problems are met in exploration, transportation, construction, mine operations, coal preparation, manpower and ecology. Paul Weir Company has been involved as coal consultants on various projects in western Canada for some years. In presenting this paper, we make no attempt to present an in-depth or detailed analysis of any one specific situation. Each has, or would have, its own peculiarities or characteristics, both physical and economic. Instead, the objective is to provide for those not intimately

Jan 1, 1972

By W. H. Emmons

THIS paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first1 outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths-the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single batholith. The outcrops of invaded rocks predominate. 5. Endobatholithic: in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants, have been -eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by, the-position on the roof, of the batholith.

Jan 1, 1927