Search Documents

By Frank G. Schwartz

VARIABLES OF composition and environment affecting storage stability of gasoline-type fuels were studied, utilizing radioactive tracers and other analytical techniques. Changes in gasoline composition brought about by aging were determined and correlated with gum formation. The amounts of reaction of selected gasoline components, measured by radioactive tracers, were determined in a gasoline-type blend and in a mixture of 17 selected pure gasoline components. The data show that sulfur compounds, nitrogen compounds, polycyclics, and olefins enter into gum-forming reactions. Certain sulfur and nitrogen compounds were found to be most reactive in the gum-forming process. Results of this study indicate that the aromatic constituents of gasolines may contribute substantially and directly to gum formation. A mixture of tetralin and indan-type compounds is reactive, and this mixture appears to be the main aromatic portion entering into gum formation. A secondary but significant amount of naphthalenes also appears to have reacted in the gum-forming process. Analyses of the sulfm compounds in a fresh and an aged fuel indicated that elemental sulfur, hydrogen sulfide, thiols, sulfides, and disulfides were depleted during aging, but thiophenes and residual sulfur compounds were not depleted by fuel deterioration.

Jan 1, 1964

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By N. D. Cristescu

The aim of the present paper is to show how a mathematical modeling of a creeping rock and that of an yieldable lining can allow us to obtain an optimization of the lining design and generally of the whole procedure and sequence of excavation-lining application. We follow the procedure presented by Cristescu (1989) Chap. 13, and Cristescu et al.(1987); for some other approaches see the literature mentioned, for instance, by Ladanyi and Gill (1988). We have in mind to describe the creep of the rock, i.e. the tendency of the tunnel to close in time, and to take into account that the lining itself may be deforming, i.e. possesses some rheological behavior. We start from the well known fact that "intelligent" lining, which are yielding to the pressure of the rock, may be much more successful in supporting creeping rocks than excessively strong, badly designed supports which are unable to resist to pressure of the rock, though these are oversized supports (too strong, too stiff, installed too early, etc.). In order to optimize the lining to be used for a certain rock, it is absolutely necessary to study in the laboratory the main mechanical properties of that specific rock and to formulate for it a reasonably simple mathematical model. Standard triaxial test results are quite enough to determine the model for the rock, combined with some creep tests which have to reveal the long-term behavior of rock (the so-called rheological model). What concerns the lining, we consider several kinds of linings existing today, for which a mathematical model was also formulated. One shows which is the interaction between the creeping rock? and the yielding lining and how can it be formulated in mathematical terms. Once written in mathematical terms, an optimization of the lining design and that of the excavation layout and support application sequence is possible. We will try to make the exposure as simple as possible, avoiding details and having in mind to give only a sketch of the problem, while the mathematical details could be worked out quite easy.

Jan 1, 1994

By R. J. Wysor

Since the outbreak of the European war, few problems of raw-material supply have commanded more nation-wide attention than potash. It is well known that before the war the domestic production of potash was an insignificant percentage of the imports. The average annual importation of raw potash salts for several years prior to 1914 was slightly over 300,000 net tons, and of other potash manure salts about 700,000 tons. The sudden and almost total cessation of these imports created a unique and stringent situation. Methods of recovering potash from feldspar and other native mineral sources, and reclamation from hitherto waste products, have received a marked impetus. Soaring prices have been a keen incentive to research and industrial development. Although several brief articles concerning the possibilities of potash recovery have appeared in recent trade journals, it still may be a matter of some surprise to the average technical mind that potash might be reclaimed as a profitable byproduct in the manufacture of pig iron. At the present time it may be of special interest to present some data, largely of a technical nature, on this subject. A fairly thorough search of the literature reveals a number of articles concerning salts of the alkali metals in the blast furnace. Many of them deal with the theoretical rôle of alkali cyanides in the furnace. Several discuss the probable effect of the alkalies on the furnace brickwork. Two or three ambitious patents have been granted for reclaiming potash or other products from blast-furnace gas. However, we have heard nothing further as to the practical application of these patents. Little literature of importance has appeared during the last 10 years concerning alkalies in blast-furnace practice, and I have discovered no record whatsoever as to the actual sale or commercial disposal of flue dust for its potash content until this was inaugurated in our plant at Bethlehem. A bibliography of the most important articles discovered is appended. About 4 years ago, in the course of investigating blast-furnace stove efficiencies, I analyzed the fine, yellowish fume of which a considerable

Jan 1, 1917

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970

By Blamey Stevens

The object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all possible cases. The generalizations of observed data, taken from Geikie's Text-Book of Geology, confornl to the laws of intrusion herein stated, and the deductions based upon these lams. No authority, however, is quoted for the type which I hare named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the nrorking of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,' there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By Christoph Mueller

Broad band mine communication today is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and TCP/IP on the other side provides an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of cheap development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefor, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. To optimize the use of bandwidth on mining networks using load limited, ?bandwidth wasting? local Ethernet segments, long distance broadband traffic should be carried out using more efficient, deterministic communication backbones providing a guaranteed quality of service for each of the physically separated networks. Open networking and broadband systems however may lead to the anticipation that any demands on bulk data or multimedia traffic can be fulfilled in the future. This definitely will not be the case as the bandwidth demands of applications will be growing as least as fast as the bandwidth provided by communication systems. Looking on those problems from an overall system integration perspective, machines and equipment in the future have to be equipped with intelligent computing devices capable of an intelligent local data preprocessing. Such ?Embedded Machine Information Servers? running commercial computing power in the future will be the intelligent bridge between open networking and a secured, high safety local automation system. These ?Embedded Machine Information Servers? then also can make advantage of intelligent video and audio data preprocessing to store and transmit multimedia information ?on demand? or when the application requires it. Summarizing the potential for the future Ethernet based networking together with powerful communication backbones and intelligent local data preprocessing on the machines in the future will lead the way to integrative, reliable and cost efficient mine automation solutions.

May 1, 2002

By Ben B. Cox

Oil produced in Iraq for export during 1938 was 31,354,090 bbl., or a daily average of 85,901 bbl; This is an increase of 182,614 bbl., or 0.5 per cent over 1937. All oil exported was produced from the Kirkuk field. The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., continued to supply local market requirements from its Naft Khaneh field in the Transferred Territories. Slightly more than 32,000,000 bbl. was produced in Iraq, a small part of which was used in field operations. During the year 12 wells were completed and 9 wells were drilling at the end of the year. Of the completions, 5 were producers and 1 was an oil-water level observation well in proved fields, and 6 were listed as failures. Basrah Concession The outstanding event of the year was the granting, by the Kingdom of Iraq, of a 75-year concession embracing approximately 89,000 sq. miles to the Basrah Petroleum Company, Ltd., a British company with French and American participation. The concession covers all parts of the Kingdom, its territorial waters, islands, submerged lands, and its interest in the Neutral Zone separating Iraq and Saudi Arabia that

Jan 1, 1939

By Ben B. Cox

Oil produced in Iraq for export during 1938 was 31,354,090 bbl., or a daily average of 85,901 bbl; This is an increase of 182,614 bbl., or 0.5 per cent over 1937. All oil exported was produced from the Kirkuk field. The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., continued to supply local market requirements from its Naft Khaneh field in the Transferred Territories. Slightly more than 32,000,000 bbl. was produced in Iraq, a small part of which was used in field operations. During the year 12 wells were completed and 9 wells were drilling at the end of the year. Of the completions, 5 were producers and 1 was an oil-water level observation well in proved fields, and 6 were listed as failures. Basrah Concession The outstanding event of the year was the granting, by the Kingdom of Iraq, of a 75-year concession embracing approximately 89,000 sq. miles to the Basrah Petroleum Company, Ltd., a British company with French and American participation. The concession covers all parts of the Kingdom, its territorial waters, islands, submerged lands, and its interest in the Neutral Zone separating Iraq and Saudi Arabia that

Jan 1, 1939

By J. F. Sepulveda, J. D. Miller

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 9, 1978

By Daniel Harrington

For several years the United States Bureau of Mines has been making a study of ventilation in metal mines, this study covering practically all the important mining districts of the country. One of the districts where a close and extended study was made was that of Butte, Mont., with its numerous interesting problems and conditions. In February, 1916, Daniel Harrington, mining engineer of the United States Bureau of Mines, was detailed to investigate the circumstances surrounding the death of 21 men in the fire at the Pennsylvania mine at Butte, and during that investigation he made underground visits to several of the large mines through the courtesy of the mine operators, and became much interested in the ventilation conditions. In May, 1916, Mr. Harrington was detailed te work in cooperation with Dr. A. J. Lanza of the United States Public Health Service in an investigation of the prevalence and causes of miners' consumption in the district. This work broadened so much that the investigation was not completed until late in 1918, the investigators making a detailed inspection of all working places in four large mines and a more or less extended examination of conditions in about 20 other mines. Ventilation was recognized immediately as being an important factor in the health of miners, and from the outset of the investigation a large part of the work consisted in obtaining and compiling data relative to the flow of air, humidity, and temperature. The officialsof the North Butte mine were engaged in making a study of ventilation problems before the coming of the investigators, so that opportunity was given to work with those officials for several months. Detailed data on air flow, temperatures, humidities, and an analyses had been obtained before the fire in the North Butte mine June 8, 1917, which resulted in the loss of 163 lives. Much information was obtained during the progress of the fire, and a detailed examination was conducted after the fire, hence an exceptional opportunity existed to study conditions relating to ventilation. This bulletin is a result of studies made from the data collected during the two and one-half years of study and observation a-boveoutlined. Its publication has been delayed through lack of funds for printing. Other publications relative to metal mine ventilation -in other parts of the United States are expected to follow.

Jan 1, 1923

By L. A. Cisternas, A. Lopez-Valdivieso, Y. L. Botero, L. Cortes

In the processing of sulfidic ores, pyrite is usually depressed and ends up in the tailings. However, pyrite is the most common species responsible for acid mine drainage (AMD) due to its spontaneous oxidation. This AMD affects the tailing chemical stability by dissolving some toxic or heavy metals species such as As, Cd, Co, Pb, and Zn, which can migrate into the surrounding ecosystems. Therefore, the strategies to reduce pyrite’s environmental impacts are a crucial point to produce more chemically stable tailings. Consequently, numerous studies have been made to find procedures that could inhibit or restrain AMD. This work aims to develop a procedure for designing conceptual flotation circuits that can produce tailings with low content of pyrite and to assess this type of circuit with traditional flotation circuits. The method consists of applying optimal flotation design where three products are considered: metal concentrate, pyrite concentrate, and tailing with low content of pyrite. Two approaches are considered; in the first, a flotation circuit is designed to generate a concentrate rich in all sulfide minerals and to obtain a tail with low pyrite content. Then, a second flotation circuit is designed for the selective separation of the bulk into metal concentrate and pyrite concentrate. This is called fractional separation design. In the second approach, a flotation circuit design is realised that generate the three products simultaneously. This is called integrated separation design. Both fractional separation design and integrated separation design are assessed in this paper. This methodology is focused on cleaner production (waste prevention and resource minimisation) rather than end-of-pipe technology (treat existing waste). The methodology was applied to a copper sulfide ore from a local company in the Antofagasta region (Chile). This ore contains chalcocite, covellite, iron oxides, and pyrite. Keywords: Flotation, tailing, pyrite, cleaner production

Jan 1, 2020

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1915 to Jan. 10, 1916. ANDERSON, FRANK BASIL, Min. Engr., Sampler, Copper Queen Cons. Min. Co., Bisbee, Ariz. BAILEY, LEWIS NEWTON, Min. -Engr 4227 St. James Place, Sail Diego, Cal. BELL, JAMES E., Min. Engr., Care Chile Exploration Co., Chuquicamata, Chile, South America. BONILLAS, YGNACIO SAFFORD, Min. Geol., Copper Queen Cons. Min. Co., Bisbee, Ariz. BRADLEY, GEORGE OLIVER, Mech. Engr Hobart Bldg., San Francisco, Cal. CLARK, GEORGE L., Min. Engr Vipond Mine, Schumacher, Ont., Canada. CONKLING, RICHARD A., Geol., Roxana Petroleum Co. of Oklahoma, Tulsa, Okla. GOHRING, W. B.. Geol., Supt. of Mines, Calumet and Arizona Min. Co., Warren, Ariz.

Jan 2, 1916

By J. P. Burland

The paper describes a number of recent case histories in the United Kingdom where field instrumentation and measurements have played a major role in the design and construction of excavations, piles and foundations. It is shown that the design and construction procedures for deep excavations in London Clay are based almost entirely on the results of field measurements. Examples are given of successful application of such measurements. The present understanding of the behaviour of bored piles in stiff clays and their design is based on a number of instrumented pile loading tests. The results of these tests have led to a radically new concept of pile design in which the piles operate at their full shaft capacity under working loads thereby resulting in considerable savings in design and construction. Some examples of the successful application of this concept are given. Finally it is shown that the present knowledge of the stiffness properties of chalk is based entirely on field observations. An example is given of how direct field measurements were used to solve a foundation problem at the base of a coffer-dam in chalk.

Jan 1, 2010

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950" to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as —75" F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But, when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service. A great deal of credit is due to the members of the Boiler Code Committee and also to the members of the Joint A.P.I.-A.S.M.E. Committee, who have formulated codes that insure the safety of the

Jan 1, 1935

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950" to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as —75" F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But, when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service. A great deal of credit is due to the members of the Boiler Code Committee and also to the members of the Joint A.P.I.-A.S.M.E. Committee, who have formulated codes that insure the safety of the

Jan 1, 1935

INTRODUCTION Within the past few years Clark (1972), King (1970), and King, et al. (1973), have summarized porphyry molybdenum occurrences. Clark (1972) includes as porphyry or stockwork deposits some occurrences more recent exploration has shown to be of other genetic types. King (1970) and King, et al. ( 1973) provide broad general descriptions that unfortunately are restricted to the US. Nor does the King, et al. (1973) description have benefit of the Wallace (1974), Hall, et al. (1974), or Giles (1975) data on alteration, fluid inclusions, or isotope chemistry. The synthesis presented here up- dates these older summaries, eliminating all but the well established porphyry molybdenum deposits as well as enumerating the unifying characteristics displayed by these deposits within the Cordillera of North America. This type of deposit occurs in the South American Andes as well, but Andean deposits are not well documented so only North American Cordilleran deposits are considered. Stockwork, porphyry, and Climax type molybdenum deposits are synonymous geo- logical labels for the large molybdenite de- posits found in parts of the western Cordillera of North America (Khruschov, 1959). These labels describe and define the type of deposit discussed herein. The term porphyry is preferred for this chapter because it describes the common characteristics; it separates the molybdenum deposits from the porphyry copper deposits, which have many similarities but also important differences. This usage also eliminates blanket application of the word stockwork to breccia pipe deposits such as Boss Mountain in British Columbia. J. R. Woodcock has contributed much to this chapter; his influence, original data, and thoughtful comments qualify him as co-author. Porphyry molybdenum deposits are characterized by fine-grained molybdenite occurring alone or with quartz and/or pyrite in fractures and open spaces of stockworks and breccias. The molybdenite is generally less than one millimeter across and in many cases too fine-grained to be seen with the aid of a hand lens. Occasionally some deposits con-

Jan 1, 1978