Search Documents

By Claudio Gutiérrez

The action of quebracho in the selective flotation of fluorite and calcite has been studied. It has been found that the unavoidable ions produced by dissolution of these minerals can precipitate calcium oleate which profoundly influences the adsorption of oleate. The depressing action of quebracho is due, at least partly, to a decrease of the oleate adsorption. The depression of flourite flotation by quebracho in the presence of calcium is due to the fact that precipitated calcium oleate can become only physisorbed, its adsorption being strongly prevented by quebracho. It is concluded that adsorption experiments with flourite must be conducted with a flotation-size mineral, which has a lower dissolution rate than when finely ground.

Jan 1, 1980

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001

By G. M. Wilemon

The Bureau of Mines conducted preliminary investigations on the use of an acid-alcohol leaching technique for recovering phosphate values from phosphate matrices. H2S04 and methanol were used as the leaching agents. Starting-matrix particle size and acid-apatite ratio were found to significantly affect the efficiency of phosphate leaching. Phosphate extractions of more than 80 pct were obtained when minus 200-mesh ore was used and the acid-apatite ratio was 8:1 or more. The iron and aluminum oxide impurities (R203) present in the crude acid products were monitored, and R203-P205 ratios are reported. Phosphate extractions in excess of 80 pct also were obtained when phosphatic clay wastes were leached. Typically, leach slurries filtered using test leaf filters ex-hibited filtration rates of 100 lb/(h·ft2) or more.

Jan 1, 1987

By Victor F. Hollister

This first section of case histories of mineral discoveries, Vol. 3, covers some of the milestones in porphyry copper and skam exploration successes. It was during the era of these discoveries that large, complex exploration departments emerged as permanent adjuncts of large mining companies. The discoveries helped shape how and where exploration activity was conducted. Probably the most important factor in exploration success is management. Few management people are mentioned in this section or in any exploration history, yet the distinction between success and failure ultimately rested with the decisions they made. One of the most successful groups was initiated by Roger Straus and Herbert Brownell when they sought to make Asarco into an important metal producer. Relying on Clem Pollock and L.H. (Bill) Hart to identify and push worthwhile projects, the Asarco management remade the company. Asarco will benefit from exploration successes com- pounded by that team for years to come. Duval is an example of a management that decided to add metal production to its industrial minerals output. When Page Morris was president, that company opened three major porphyry copper mines and became an important factor in metals. Under the Monis management team, Duval became a leader in exploration. At the other end of the scale are managements that snatched defeat from the jaws of victory and by so doing changed the character of their companies in other ways.

Jan 1, 1991

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

By Ralph Schilthuis

SEVERAL investigators1-8 have reported evidence of the existence of native or connate water in oil-and-gas-bearing strata. Both water and salt have been detected in cores of oil sands that yielded oil and gas exclusively when produced. Electrical logs often reveal unexpectedly low resistivity through oil and gas sands, indicating the presence of some material that is a considerably better conductor of current than oil and gas. Furthermore, calculations9 of the oil and gas content of reservoirs based upon production and reservoir-pressure decline data indicate appreciably lower values than are arrived at under the assumption that the pore space is occupied completely by oil and gas. ORIGIN AND OCCURRENCE OF CONNATE WATER IN OIL-AND-GAS-BEARING FORMATIONS The view has been expressed,10-15 and is generally agreed upon, that the expulsion of oil and gas material from source beds and the subsequent migration and accumulation occurred in the presence of salt water. As the strata that usually form reservoirs for oil and gas were laid down by, or in the presence of, ancient seas, the pore space within the strata must have been saturated with salt water before the entrance of the oil and/or gas. Thus, the accumulation of oil and/or gas in the upper regions of structures suitable for reservoirs must have required displacement of the connate water therefrom. In the absence of any forces other than gravitational, it would be expected that the displacement of the connate water out of the zones finally occupied by gas and oil would be complete, and that the vertical distribution of gas, oil, and water in a reservoir would be strictly in the order of their densities. Apparently, however, surface and interfacial forces that will not permit complete segregation of the fluids are active within the capillary spaces comprising a reservoir. The effects of these forces on both accumulation and production of oil and gas have been the subject of study by a number of investigators. 16-37

Jan 1, 1938

By J. Howarth

Two electrochemical processing methodologies have been used to electrogenerate bromine-laden solutions for gold-leaching purposes. In the first process, a laboratory-scale cell in which the anode and cathode compartments were separated by a cation-exchange membrane was employed. The bromine produced by electrolysis of a 4% bromide solution was used to leach gold from a low-grade ore. The pregnant leach solution was then returned to the cell to recommence the cycle. High current efficiencies (90-93%) were maintained over six cycles. In the second process, an undivided hypochlorite generating cell (Chloropac"') was used to generate bromine from a simulated leach solution. Electrolyses were performed on a pilot-scale (100-150 gallons) with solutions containing different levels of bromide ion. The current efficiencies were also high (80-90%) and unaffected by the bromide concentration (over the range 2.5-5%) provided the electrolysis was run to low conversion « 15%). The Chloropac module was capable of delivering 0.6 kg bromine per hour at a power cost of $0.09 per kg. Using these figures, a detailed economic assessment for a 1000 metric tonnes (MT) per day gold ore processing plant was made. Electrolytic regeneration of bromine in a gold leach/recovery circuit dramatically improves the process economics over cyanidation.

Jan 1, 1991

By Alan James Parker

Chalcopyrite can be converted to pure copper by the following five steps. An exothermic sulfation roast of chalcopyrite; leaching of cupric sulfate from the calcine with dilute acid; precipitation of Chevreul's salt and or other copper sulfites with ammonium sulfite or precipitation of crude copper by autoclaving ammonium sulfite and cupric sulfate at 150°C; dissolution of Chevreul's salt, or the crude copper, as cuprous sulfate, using acidic cupric sulfate in an acetonitrile-water solution as oxidant; precipitation of pure copper by thermal disproportionation of the cuprous sulfate solution. Acetonitrile and acidic cupric sulfate solution recycle. Advantages over conventional processes include lower cost, lower energy consumption as waste heat, sulfur removal as ammonium sulfate or gypsum, rather than as sulfur dioxide and rapid throughput. The net reaction is: 2 CuFeS2 + 4H20 + 15/2 02 + 8 NH3?2Cu + 4 (NR4)2 SO4 + Fe2O3

Jan 1, 1976

By Thomas L. McVay

Laboratory batch and pilot plant flotation tests were made to determine the feasibility of recovering commercial grade kyanite from a quartzite- kyanite rock from the Graves Mountain, Ga., deposit. Best results in laboratory and continuous tests were obtained using sodium carbonate for pH control, citric acid for quartz depression, and oleic acid as the kyanite collector. Over 80 percent of the kyanite was recovered in a concentrate analyzing 56.8 percent Al203 and 3.8 percent hydrochloric acid soluble Fe203. Subsequent treatment of the flotation concentrate by magnetic separation reduced the acid soluble Fe2O3 to 0.6 percent and increased the alumina content to 59.2 percent. Acid leaching of the concentrate gave a product analyzing 59.7 percent Al203 and about 0.1 percent Fe203. As a result of the beneficiation research, a commercial kyanite flotation plant was completed in September 1962 by private industry.

Jan 1, 1963

By Ward Sumner

The Jones Hill prospect is a Proterozoic age, volcanogenic, semi-massive to massive sulfide deposit. The deposit is located on the western edge of the Pecos greenstone belt in the southern Sangre de Cristo Mountains of northern New Mexico. The prospect is found in a block (West Block) of meta- igneous rocks, primarily diabase, metavolcanic rocks, and metasedimentary rocks (fig. 1). This assemblage is typical of lithologies found in the greenstone belt. Metamorphic grade is greenschist to lower amphibolite. The West Block is bound- ed on the west by Proterozoic age (1.7-1.4 b.y. by Rb/Sr), granitic plutons collectively called the Embudo granite, and on the east by Paleozoic sedimentary rocks, primarily sandstones, shales, and limestones of Mississippian and Pennsylvanian age. The mineralization occurs in a single horizon which has been overturned and cut into two blocks by a high-angle reverse fault (fig. 2). The mineralized horizon is found at the contact of felsic metavolcanic and rnetavolcaniclastic rocks with overlying intermediate metasedimentary rocks. The local stratigraphic sec- tion from bottom to top is as follows: 1) porphyroblastic quartz- sericite schist (originally a rhyolitic, subvolcanic intrusive); 2) quartz-sericite-chlorite-biotite schist (felsic metavolcanic and metavolcaniclastic rocks); 3) chlorite-talc-biotite-sulfide schist (altered felsic metavolcanic rocks); 4) carbonate-quartz-sulfide [ ] chlorite-tremolite-talc schist (mineralized exhalite); 5) quartz- chlorite schist (silicified tuff); and 6) amphibole-chlorite-feldspar- biotite schist (occasional mafic to intermediate metavolcanic flows).

Jan 1, 2013

By Stanley J. LeFond

After two disappointing years where most industrial minerals posted decreasing production, 1981 saw an increase in production over 1980, or at least in status quo. Several commodities did, however, post significant gains. For example, bromine posted a 14% increase; fluorspar production dropped 21% in 1980, but gained 24% in 1981; and sulfur production increased. However, perlite was off 13% and manufactured sodium sulfate off 18% in 1981, while natural sodium sulfate production remained almost even with 1980. In fact, many industrial minerals production either remained constant, increased, or decreased only slightly over 1980. Increasing energy costs had their impact on industrial minerals in 1981. Hopefully, the recent downward trend in energy costs, at least gasoline, will financially help some of the more marginal plants. The 1979 shortage of rail cars that did not carry through 1980 also did not carry through in 1981. Rail rates increased 12.8% over-all last year, while average freight rates for industrial minerals increased 15.5%, according to Neil Johnson, consultant. Also, the trucking industry posted a 5-6% decrease in rates due to deregulation. All in all, we in the industrial minerals section seem to be holding our own at least. Stanley J. Lefond Contributing Editor

Jan 5, 1982

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973

By Kinsella B

Titrimetric studies have been carried out on the activated carbons Kintal 1105, Norit 2520 and Kuraray 2GA. Titration curves of the carbons before and after acid and water washing and gold loading indicate that the acid-base properties of the carbons are affected by both the method of treatment and also by the loading of gold. It is considered that the pKa values of the functional groups on the carbon surface are in the regions of 11, 7 and 3 respectively.

Jan 1, 1984

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

By Mahesh C. Meyer Jha

AMAX has developed a chloride refining process to produce pure nickel and cobalt metals from mixed sulfide .precipitates, Metal chloride solutions, generated in a hydrochloric acid leaching step and purified in a solvent extraction circuit, are converted to metal oxides .and HCI gas by pyrohydrolysis. A pilot plant consisting of a 30-inch diameter fluidized bed reactor and other ancillary units was designed, constructed, and operated for over one year. Process design was aimed at minimizing energy consumption, maximizing conversion efficiency, and achieving simplicity of operation and control. The operation provided valuable information on process scale up parameters, process control strategies, and materials of construction., Several process variables such as bed temperature, solution composition, solution feeding system, bed particle size distribution, and fines recycle system were investigated to determine their effects on process efficiency and the physical and chemical characteristics of the product.

Jan 1, 1985

By Cyro Takano

An alternative use for recycling of waste from bag house of iron ore sinter plant was tested by producing and evaluating" at laboratory scale, the self reducing cold bonded pellets. This waste was characterized and the self-reducing pellets were produced using anthracite coal fines as reductant and Portland cement or hydrated lime/Blast Furnace slag as binder. It was used the molar ratio of Fe2O3/C (fix) equal to 3. Evolution of cold strength with curing time, for different contents of binder, was evaluated. Cold strength of 200N/pellet was obtained, for sinter dust, after 10 days of curing. Suitable hot strength was also presented and no decrepitation and swelling were observed. Good fractional reduction was obtained at 950°C and 1137°C. These results show that this material may be used by the Self-Reducing Processes for hot metal production, as an alternative route for this dust destination.

Jan 1, 1996

By L. C. George

The Bureau of Mines measured the vapor pressures of selected mixtures in the binary systems CdCl2 ?SnCl2, CdCl2 -ZnC12, PbCl2 ?SnCl2, and PbCl2 -ZnCl2 by the static pressure method. These data were evaluated by the second-law (sigma-plot) method. Equations expressing the vapor pressures and the heats and free energies of vaporization as functions of temperature are given.

Jan 1, 1969

By Akira Ishizu, Nobuo Matsui, Hideo Yamamoto, Tatsuya Nagahama

At Kamioka Mine of Mitsui Mining & Smelting Co., Ltd., Japan there are three mills, treating a total of 6400 t/d of lead-zinc Ore. In the lead-zinc bulk differential flotation at Shikama Mill the addition of reagents is automatically controlled by the feed rate, the lead and zinc content in feed, froth and tailing, the pH and the concentration of cyanide ion in the pulp. As the zinc thickener overflow at Shikama Mill contains CU(CN)3--, ZnS, CdS, CN-, xanthate and frother, all the ingredients in the over- flow other than CN are floated by using the Nagahm flotation machine, and the water containing only CN- is effectively recycled to the lead- zinc differential flotation circuit. In the lead-zinc straight differential flotation at Mozumi Mill, the overflow of tailing pond is recycled especially to the cleaning flotation circuit by decreasing the pulp density. Thus the integrated recycling of wastewater greatly reduces environmental problem and in addition, it generates sizeable profit.

Jan 1, 1977

By F. E. Block, T. T. Campbell, D. Z. Hobbs

Several methods were investigated for the preparation of high- purity elemental boron in an attempt to develop a feasible process for producing boron on a large scale . In the work described in this report , the metal was prepared by metering boron trichloride gas into a crucible containing molten metal reductants . It was necessary to remove reaction byproducts by acid and aqueous leaching . Magnesium and sodium were tested as reductants , but best results were achieved using lithium or zinc as reductants . Contaminants originating from the materials of construction were the chief impurities in boron made by this method . Impurities ranged from 0.5 to 5.0 percent . Impure boron ( 85 to 90 percent ) was also prepared by the magnesium reduction of boron trioxide in a thermite - type reaction . This product contained magnesium as the chief contaminant . Impure boron made in this way could be upgraded by fusing with potassium fluoborate or potassium acid fluoride . After acid leaching the fusion cake , a product containing 95 to 97 percent boron was obtained . Analytical techniques for accurate determination of impurities in elemental boron are a major problem , requiring solution before a valid comparison can be made of the quality of boron prepared by these various methods .

Jan 1, 1964