Search Documents

By Jorge Navarrete

La Corporación Nacional del Cobre de Chile produce cobre y otros subproductos a través de sus yacimientos y líneas de producción como las pirometalúrgica, hidrometalúrgica y biohidrometalúrgica. En este sentido, el presente texto señala la implantación de un LIMS para la industria minera de cobre. LIMS es una abreviatura genérica para los software de Administración de Información de Laboratorio, cuyo objetivo es relacionar la Informática, Quimiometría y Calidad.De forma que cumpla con los objetivos de adquisición y gestión de la información de pesaje, muestreo y análisis químico producida por diferentes áreas, tanto internos como externos y unidades funcionales.

Jul 17, 2000

By J. Bruce Clemmer, M. F. Williams, B. H. Clemmons, Carl Rampacek, R. H. Stacy

"INTRODUCTION This report is the first of several dealing with the application of flotation methods for beneficiating the calcareous and siliceous red iron ores and ferruginous sandstones of the Birmingham district. The flotation study was part of a general investigation of the concentratability of various iron ores of Alabama and other Southeastern States undertaken by the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, Tuscaloosa, Ala.Batch testing and pilot-plant flotation testing of the calcareous red ores of the Birmingham district have been in progress for several years, and although some phases of the study are not yet completed, enough data are available to indicate that many of the ores will yield marketable-grade concentrates with good recovery.The first flotation tests on the calcareous red ores employing conventional methods either the iron oxides or the siliceous gangue materials failed to give the desired results. The inferior separations obtained or prohibitive reagent requirements made the methods unattractive. Other more effective flotation methods were sought. A laboratory study of various reagents was undertaken. It resulted in the development of two attractive methods embracing anionic flotation of the activated siliceous gangue from the retarded iron oxides. The methods were similar in that fatty acid or soap-collecting agents were employed in strongly alkaline pulps to float the naturally activated quartz from the iron-ore pulps. The methods differed, however, in the addition agent employed to retard the hematite or hematite and calcite. By proper choice and quantity of the addition agent, the calcite could be floated with the quartz or retarded with the hematite as desired. Ability to recover or reject the calcite gives added flexibility to the separation. Although the methods have their limitations and cannot be considered ""cure-alls,"" they have given encouraging results on a number of calcareous red ores that heretofore proved difficult to concentrate by conventional flotation procedures."

Mar 1, 1945

Tumbling mills and some theoretical and practical aspects of milling are discussed. Attention is directed towards the difficulty of relating the dynamical analyses of the motions of particles within mills to the existing treatments of breakage processes. This synthesis may be advanced by a study of milling that utilizes the matrix analysis of breakage processes. Application of the matrix analysis to results obtained on (i) grinding in open-circuit a zinc ore in a conical pebble mill and in a modified conical mill, (ii) "grinding of cement clinker in a compound mill, and (iii) to some drop-weight grindability tests is discussed. It is shown that the 'IT-breakage model adequately describes the breakage processes of each of the tests. (The proportion broken in each breakage cycle is given by 'IT and is independent of particle size.)The size distributions of the products are accurately predicted in the cases considered. Matrix analyses of the breakage of coals, various ores and a cement clinker have been made. Appendices give an elementary account of the matrix methods and give the equations fully describing reverse order closed circuit operations. The matrix analyses of breakage processes and the survey are used to examine briefly closed circuit grinding.INTRODUCTIONTumbling mills are slow-speed crushing and grinding machines which have been developed from some fairly simple types into many widely differing forms. Many of these versatile mills have proved extremely useful in ore dressing and mineral beneficiation, whereas others have been used in the cement industry and less extensively in the coal industry.The performance of even the simplest tumbling mill is very imperfectly understood, whilst the more difficult problems associated with the balancing of complex milling circuits and with the establishment of the optimum operating conditions for the whole of a complex circuit are even less well apprehended.Our knowledge of the performance of tumbling mills is rather sharply divided into two categories: the first consists...

Jan 1, 1957

By Diego Ruben Martin

Este trabalho objetivou comparar, por meio de experimentos desenvolvidos em uma fundição, através da adição de três inoculantes diferentes (IM-22 com FeSi-Ba/Zr, G 20 com FeSi-Ba) e IMSR 75 com FeSi-Sr), para observar as características da vida util de ferramentas na usinabilidade das peças, microestrutura e propriedade mecânica. A metodologia da pesquisa se baseou em analisar principalmente pelo processo de fresamento o ferro fundido cinzento GG-25 inoculado diferentemente, denominado de acordo com a Norma DIN EN 1561. As formas de avaliação dos resultados terão como base uma análise quanto ao desgaste da ferramenta, acabamento superficial, análise microestrutural, composição química e propriedades mecânicas do material da peça. Os resultados mostraram que dentre os inoculantes aplicados o com Sulfeto de Estrôncio (SrS) apresentou-se mais estável termodinamicamente que as amostras inoculadas com os outros dois inoculantes, pois ele levou a uma variação da energia livre de Gibbs mais negativa e portanto mais favorável a formação de núcleos com raio crítico (rc) maiores, o que permitirá uma solidificação com nucleação heterogênea. Todavia o respectivo inoculante também foi mais eficiente na formação de uma microestrutura mais estável, com maiores quantidades de células eutéticas e vida útil do inserto mais longa quando usinado.

Aug 16, 2017

By W. A. Tiller, W. C. Johnston

The solute distribution ahead of an advancing solid-liquid interface is controlled by varying the momentum boundary layer thickness in the liquid adjacent to the interface. Single pass zone-melting experiments on Pb-Sn alloys are described in which the liquid is caused to rotate in the plane of the solid-liquid interface due to the influence of a magnetic .field rotating in this plane. The variation of the diffusion boundary layer thickness with field strength is determined. DURING the freezing of an alloy a partitioning of solute occurs at the solid-liquid interface, the magnitude depending upon the difference in the solid and liquid solubilities at the interface temperature. Because the diffusion coefficient is so small in the liquid relative to normal freezing rates, either a pileup or a depletion of solute occurs at the interface when the partition coefficient, kO, is either less than or greater than unity, respectively. This solute distribution is completely characterized by i) the solute concentration in the liquid far from the interface, C) the ratio of freezing velocityf, to diffusion coefficient, D, iii) the partition coefficient, ko, and iv) the thickness of the diffusion boundary layer, 6,, at the interface (this assumes that an electric field is not applied across the interface). For a particular system, C ko and D are fixed so that the character of the solute distribution can be changed only by a variation of either f or 6c. As is well known, the freezing velocity can be changed by varying the thermal environment of the alloy. Whereas, the thickness of the solute rich layer can be changed by varying the fluid flow conditions in the liquid. It is the purpose of this paper to describe a technique for controlling the fluid flow conditions in the liquid. During most solidification experiments the driving force for fluid flow arises from either mechanical mixing, thermal convection or electromagnetic mixing. The momentum boundary layer thickness, 6m at the solid-liquid interface, within which negligible movement of the liquid occurs, has been calculated for the special case of mechanical mixing where crystals are solidified by the Czochralski technique.l,2 The calculation of 6m for the case of thermal convection has also been made.3 In some calculations it has been assumed that the momentum boundary layer thickness, 6,, may be equated to the thickness of the diffusion boundary layer 6c, at the interface. However, as may be seen from Appendix I this is only true in very special cases and in general where a is a constant of magnitude determined by the particular liquid alloy. Neither calculations nor experimental data exist for the dependence of upon electromagnetic mixing. In this paper experiments are described in which the liquid is caused to rotate in the plane of the interface due to the torque developed on it by a magnetic field, H, rotating in this plane. The variation of is controlled by the variation of H. A magnetic field rotating in a plane perpendicular to the interface has been used for the purification of aluminum. Experimentally, we determined the variation of 5C with H by using the zone-melting technique of pfann5and a theoretical relationship of Burton et a1.2 pfann5 has shown that, after the passage of one molten zone through a long cylindrical charge of uniform concentration, CO, the solute distribution, C,, in the solid is as shown in Fig. 1. The equation describing this distribution is

Jan 1, 1962

By Alexander Schultz Rizek

O trabalho que será apresentado irá descrever o projeto realizado de atualização tecnológica do sistema de controle com controladores Automax instalado em um laminador de fio máquina de dois veios, a Acerías Paz del Río, da Votorantim Siderurgia na Colômbia. Este projeto consistiu na substituição do antigo sistema de controle com PLC’s Automax do laminador fio máquina de dois veios, mantendo-se parte do sistema antigo Automax convivendo com o novo sistema Contollogix. O novo PLC instalado para o controle do laminador foi o Rockwell ControlLogix, através do qual foi desenvolvido o controle principal do laminador, como: cascata de velocidade utilizando o fator R, que poderia ser ajustado do IHM (antes os ajustes eram feitos diretamente no rpm dos motores), controle de laços, controle das mesas de laço, as primeiras da Russula, produzidas e programadas em companhia com a Russula Itália exclusivamente para esse projeto, controle de tração, ciclos de posicionamentos manuais e automáticos, intertravamentos, etc.

Jul 30, 2018

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18'-11" OD Brooklyn Tunnel; the 5-mile long, 23'-2" OD Queens Tunnel, and the9-mile long, 12'-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007

By AIME AIME

BUFFALO, Queen City of the Lakes, singularly accessible by land, water and air, will be the mecca for metallurgists throughout the United States and Canada during the week of the National Metal Congress, Oct. 3 to 7. Headquarters during the National Metal Congress will be the Hotel Statler and there on Wednesday and Thursday, Oct. 5 and 6, the Institute of Metals and Iron and Steel Divisions, A.I.M.E., will hold a series of technical sessions, the annual Science Lecture, a dinner and executive committee meetings. The American Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron and Steel and Machine Shop Practice Divisions of the American Society of Mechanical Engineers, the Wire Association and the American Drop Forging Institute will present a carefully planned program extending throughout the week.\

Jan 1, 1932

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By P. W. Jensen

Gold deposits in Interior Alaska are commonly coincident in time and space with reduced, mid-Cretaceous granitoids. The True North deposit of the Fairbanks district is several km from such granitoids, but yields mineralization ages indistinguishable from the Fort Knox granite-hosted deposit. True North, however, resembles sediment-hosted epithermal Au, demonstrating the variability of intrusion-related Au deposits in metamorphic rocks. The True North deposit (14M tons at 1.5 gpt) is hosted within a carbonaceous thrust complex separating eclogite facies from amphibolite facies rocks, located > 5 km from mineralized granite outcrops. The ores contain anomalous Sb, As, and Hg (stibnite is the most common sulfide) with ankerite-sericite alteration in steep NE-striking ?feeder? shears and low angle thrust shears. Nearest hornfelsed rocks are located > 1 km away, and across several high-angle faults. Fluid inclusion data indicates trapping temperatures of ~250C from low-density, low-salinity fluids at P < 0.5 kb. Au was originally present as solid solution in sulfides; minable ores are restricted to the oxidized upper 100 m of the deposit. The considerable differences between this deposit and the temporally equivalent Fort Knox intrusion-hosted deposit indicate no one description adequately characterizes this deposit type.

May 1, 2003

By A. M. Gaudin

Jan 1, 1962

By P G. Gaylard

The minerals Industry carries out over US$ 2 billion of R&D annually. The R&D is performed at three levels ? in house research facilities; on a one-on-one basis with a research provider; as syndicated (collaborative) research. The key to a successful R&D programme is project selection. It is suggested that at this time of ?bounty? for the minerals industry the research portfolio should contain some ?blue sky? but potentially long term significantly beneficial projects. This said, the projects should align the technical concepts with the business imperatives. AMIRA has found the ?Road Map? concept has assisted in defining areas for R&D. Examples of this methodology using a Copper Road Map developed by AMIRA for the copper producers operating in South America is presented. The benefits derived from syndicated research are also discussed.

Jan 1, 2007

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 &#181;m using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By W. J. Millard

IT is well known that the excellent mica from Brazil played a most vital role in World War II. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the United States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. TYPE OF DEPOSIT FAVORABLE The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than I:3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. THE ECONOMICS OF STRIPPING When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run II per cent good stain and better when trimmed and contain 2 kg. of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should he used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.I4 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.I5. To this should be

Jan 1, 1946

Cospidie (3CaO*2SiO2*CaFe2) is one of the most important compounds crystallized in mold flux films during casting in the continuous casting process of steel, The primary crystallization field of cuspidine has been experimentally developed in the CaO-SiO2-CaF2-SiF4 system. The cuspidine-NaF binary and cuspidine-CaF2-NaF ternary systems have been also experimentally determined to study effects of addition of NaF on the primary field of cuspidine. In order to discuss its thermodynamic stability the standard Gibbs energy of formation of cuspidine has been deterimed by an electromotive force methods using CaF2 as solid electrolyte and a transpiration method as follows: ^fG° (cuspidine) /kjmol-1 = 5198 + 0.825T (+12) (1313<T/K<1329): EMF method ^fG° (cuspidine) /kjmol-1 = 5178 + 0.813T (+8) (1221<T/K<1469): Transpiration method The chemical potential diagram and constituent activities for the CaO-SiO2-CaF2 System have been evaluated based on the obtained thermodynamic data.

Jan 1, 2003

By Parviz Montazer, Robert King, William Ubbes, Gideon Chitombo

This paper describes the results of a detailed study that was undertaken to define the spatial distribution of permeability within a five meter thick envelope around the CSM/ONWI room. Detailed fracture orientations and distribution were determined through mapping of the walls of the opening, logging of oriented core, and visual examination of borehole walls with a borescope and a T.V. camera. Over 3,500 measurements were made from which the three dimensional distribution of fractures was determined. Two principally different testing equipment designs and various methods of air injection tests were used in all boreholes to identify and characterize conductive fractures. Through analizing the distribution of permeability and fracture index around the room a zone of blast damage of approximately .5 m thickness was delineated. The effect of stress modification seems to extend farther into the host rock to approximately 3.5 m depth.

Jan 1, 1982

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia&apos;s newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958