Search Documents

By H. D. Newell

Jan 1, 1938

By N. Menad

The formation of the dioxins can be dependent on the quantities of carbon, hydrogen, chlorine and oxygen present in a given system, as well as on parameters such as temperature and pressure. Inadequate supply of combustion air ( incomplete oxidation ), low combustion temperatures ( incomplete combustion ), and insufficient turbulence in the combustion are factors which can favour their formation. Dioxins were produced also calatytically from chlorinated phenol precursors, non-chlorinated compounds that were chemically, and reaction of phenol with inorganic chloride. In this paper different precursors such as combination of C, H, 0, Cl, rapid formation/combustion intermediates and routes to PCDFs are reviewed, and the influence of PVC amount on the formation of these isomers is discussed.

Jan 1, 2000

By Ian W. Wark, Keith L. Sutherland

IT has been shown' that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "standard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,2 it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator. It is not difficult to suggest an explanation for the influence of the carbonate ion in the presence of copper sulphate. The works of Picker-

Jan 1, 1939

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972

By D. A. Saint Don, M. Prueher, S. Barnwell

With the current changes in technology, multiple methods are now available for aggregate resource identification. From Sonic to Coring, Reverse Circulation to Percussive, there are many choices to make regarding drilling technology. The discussion will outline the methods above with focus on aggregate investigation and highlight the new technologies that will make a difference in your search.

Jan 1, 2004

By Wiley C. Buford

Gary Works No. 1 BOP Shop is a three furnace shop which went into operation December, 1965. The heat size is over 200 tons, with a substantial percentage of the production used to feed a Continuous Slab Caster. Vessels are driven by a shaft mounted bull gear and main housing utilizing eight 35 HP flange mounted motors and primary gear reducers. Torque absorption is controlled by two spring actuated torque arms. At 1:00 p.m. on Thursday, August 6, 1970, as "E" furnace was being turned down for a preliminary test, the drive side trunnion bearing failed. The furnace dropped slightly and shifted several inches north in the direction of the drive unit. The decision was made to tap the heat which was done without incident and the vessel uprighted. No attempt was made to completely drain the slag from the vessel, so as to avoid any further damage to the trunnion shaft bearing surface. The bearing failure occurred approximately four years and eight months after start up of the shop. Unfortunately ?M? furnace had gone down for a normal reline two days prior to the bearing failure, leaving the shop with only one operating furnace.

Jan 1, 1972

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

Jan 1, 1891

By M D. Rosengren, G Gregor, M F. Young

Over the last 15 years the silver/lead/zinc ore treated at Mount Isa became increasingly complex and lower grade. Metal recoveries dropped dramatically, causing a serious decline in profitability. The ætraditionalÆ response of increasing tonnage to reduce unit cost was unsuccessful, since the additional tonnage was even lower quality ore. A major technical and capital program in the 1990s restored metallurgical performance, but business return was still too low and ore quality continued to decline. In 1996 a new, holistic approach integrated the steps of geology, mining, concentrating, smelting, and refining. Previous assumptions about æfixedÆ and æmarginalÆ costs in mining and processing were shown to be wrong. Detailed analysis showed that some ore sources were reducing profit. This led to a fundamental redesign and downsizing of both Mount Isa and Hilton mines. The result was dramatic increases in head grades, metallurgical performance and plant stability without any capital expenditure. The business is now smaller, but more profitable.

Jan 1, 1998

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By R. B. Sosman

INTRODUCTION IT is well known that ferric. oxide, Fe.-,03, is paramagnetic, while magnetite, Fe304, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe-03 and Fe304 have been almost completely lacking. Fe203 and Fe304 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe203 toward Fe304, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe304, but it has not yet been possible to establish the existence-of such a break experimentally. The occurrence of solid solution ill this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe203 to Fe304. The oxygen-pressure curves at 1,100° and 1,200° are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe203 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is im-possible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe304 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great hulk of natural oxides of iron lie fairly near either Fe203 Or Fe304 in composition. The reason will be

Jan 6, 1917

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By D. C. Treilhard

After a brief history of the mining and smelting operations of Kilembe Mines Limited, this paper outlines the smelter layout and describes . the. daily operations at the Jinja plant. Particular attention 1s paid to the details of the furnace and converter operation. A subsequent section of the paper deals with the significant developments in plant metallurgical practice, covering both smelting and converting.

Jan 1, 1966

By John A. Ames

Webster's dictionary nearly equates portland cement with its current primary definition of cement. While such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to "varieties" of portland cement including "portland-pozzolan" cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far corners of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry between 1756 and 1972 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. As part of the 4th edition of Industrial Minerals and Rocks, this chapter on utilization focuses on inferred interests of the anticipated readers. The main period for which statistics are cited generally is that since the 3rd edition (1960) of this same volume. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or "burning") step, which brings about the necessary changes in the raw materials. This pyro processing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The U.S. Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relate to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. The year 1972 witnessed a test of the adaptability of cement industry statistics. This was the year of conversion from barrels and sacks of cement as the units of measure to tons and hundredweights. The barrels and sacks related to volumetric measures in that a sack was judged to be 1 cu ft (weighing a "standard" 94 lb). A barrel was 4 sacks. Volumes of concrete are stated in cubic yards, and the number of cubic feet of cement in a cubic yard of concrete was a sensible approach to the mensuration involved. However, cements do not weigh the same amount from plant to plant or from type to type, and the buyer was more interested in getting an assured weight for his money than in "buying air." Thus, a sack, in accepted practice, became 94 lb instead of 1 cu ft, and a "barrel" became 376 lb, regard- less of whether it would fit into 4 cu ft of space. With the de facto dealing in weight rather than in volumes, the awkward numbers made little

Jan 1, 1975

By P Barrette

The manual gravimetric drying moisture determination methods currently employed by most mineral processing plants fail to provide timely and accurate information required for automatic control. The costs associated with transporting and handling concentrates represent a major portion of the overall treatment price. When considering the cash flow of a mining operation that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, any tool that provides real-time feedback on the process is vital (Edwards, RP 1994). The introduction of an on-line moisture sensor would become a welcome addition to the process control field instrumentation package now applied. A novel on-line determination system for ore concentrate moisture content would replace the tedious manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum. Therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the æwish listÆ of mineral processors since the problem has always been that you can only control what you can measure, (Konigsmann, 1990). Today, the task of moisture determination is still done by the classical technique of loss in weight utilising uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of seven to nine percent, but controlling the moisture content below eight percent is a difficult task with a manually controlled system. Many times, delays in manually achieving reliable feedback of the moisture content results in the moisture varying from five to twelve percent before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper introduces and describes a unique and promising novel on-line moisture sensor employed for mineral processing de-watering applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimisation of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarise the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content. The commercial model of the equipment is described with the features and benefits to the users summarised.

Jan 1, 2003

By F. W. Luersson

High carbon, low phosphorus steel can now be made from pig iron containing 0.7 pct P or more, in a commercial sized open hearth furnace. No external heat is required for refining, and steel produced is identical with basic open hearth steel. THE classical Thomas process, which requires liquid pig iron containing over 11/2 pct P, yields a product relatively high in phosphorzs and nitrogen. Unless large quantities of recarburizers are added to the refined steel, the product is low in carbon content. Thus, the Thomas process is not well suited to American raw materials, and its product is often not acceptable according to the standards set by American industry. The shortcomings of the Thomas process have long been recognized; with the advent of low cost oxygen, studies were initiated to develop pneumatic processes which would conceivably overcome the inherent objections to Thomas steelmaking. Several such modified basic pneumatic processes have been tested experimentally in commercial trials during the past decade. Probably the most widely publicized of these developments has been the oxygen converter process as practiced in Austrial,2 and in Canada.8 n this process, oxygen is substituted for air and introduced above the liquid bath in order to increase the heat available to the metallurgical system. This avoids the need for high phosphorus raw materials and gives a product low in nitrogen. In this process, the phosphorus content in the final product depends, to a considerable extent, on the total amount of that element in the burden. The rotary furnace4 which is now in commercial operation at Domnarvet Steelworks, Sweden, is producing low phosphorus steel from iron containing 1.8 to 2 pct P. One or more early slags are removed and by this means high carbon steels of open hearth quality can be produced. At this stage of development there is some question as to the applicability of the rotary process to large heats. Another development has been the use of oxygen in combination with either steam6 or carbon dioxide yn the basic bessemer, thus avoiding the introduction of nitrogen gas into the refining system and giving a product relatively low in nitrogen content. A double slag process has been used in Europe7 in conjunction with a regular Thomas converter, by means of which it is possible to obtain a phosphorus content in the product approaching that obtained in basic open hearth steels. The Turbo-Hearth process:' which uses the side blowing principle so as to produce low nitrogen steel from normal American pig irons, has been developed experimentally in this country. A process fitted to U. S. raw materials All of the preceding processes, with the exception of the rotary furnace, suffer from the common shortcoming that they cannot be adapted to the production of high-carbon, low-phosphorus steels unless large proportions of recarburizers are added. In 1947, a program was initiated by the Inland Steel Company1' to study an oxygen steelmaking process specifically designed to utilize the full range of phosphorus analyses encountered in American pig irons and to give finai products with phosphorus and nitrogen contents comparable to steel produced by the basic open hearth process. Some of the objectives of the proposed process are: 1) the process should be able to accommodate molten pig iron conta;rl;rrg up to 1 pct P., 2) sne process should be subject to close control of carbon analysis, 3) the process should be capable of producing high carbon

Jan 1, 1958

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985