Search Documents

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By Roger Potvin

Abstract The demand for pure zirconium and titanium metals in Germany increased considerably during the war. Pure zirconium was used in flash bulbs, in vacuum tubes, and in time fuses for bombs, where it has a decided advantage because it gives no gas in burning. Under the form of alloy, it was used with other rare elements for making substitutes for platinum; it was also used as a scavenging agent in high-grade steels. Metallic titanium was mainly used in connection with the manufacturing of special alloys. The authors were sent to Germany by the Department of Reconstruction and have investigated the German process developed for producing these rare metals. They describe the procedure and special equipment used for their commercial production in Germany during the war. General Metallic zirconium and titanium were .produced on a commercial scale in Germany by the thermal reduction, with metallic sodium, of potassium fluozirconate and titanium chloride, respectively, using a mixed potassium and sodium chloride flux. According to the information gathered, the sole German producer of these rare metals in pure form was the Deutsche Gold und Silber Scheideanstalt (commonly called Degussa), at their Werk II, 215 Gutleutstrasse, Frankfurt/Main, which was visited by the authors on September 18th, 1945. As far back as 1934, Degussa was carrying on active research on the manufacture of zirconium, and nearly one ton of the pure metal had been produced before September, 1939. Concurrently, a quite similar process was worked out for the recovery of titanium and it was in commercial operation in the year 1938, during which the production totalled about half a ton (metric). The demand, especially for pure zirconium, increased considerably during the war, attaining a total of about 48 tons during the period October, 1939, to the end of 1944, and reaching a peak of more than 15 tons in 1943. In 1944, the plant was slowed down due to the frequent and disastrous bombing by the Allies, especially in March and September.

Jan 1, 1946

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1964

By A. Visnapuu

High-grade synthetic rutile has been produced in the laboratory from domestic ilmenite concentrates by a new carbonyl process. The ilmenite was first reduced to convert the iron oxides to metal and then treated at temper-atures over 1000 C in high-pressure carbon monoxide (CO) to convert the iron to the pentacarbonyl. Rapid carbonylation was achieved in the presence of small quantities of selected promoters. Maximum iron removal occurred at temperatures between 110° and 130° C at CO pressures from 1,000 to 1,400 psig. Iron pentacarbonyl appeared as liquid and vapor in the reactor and could be removed by gravity flow and vapor transport. More than 90 pct of the iron was extracted in 2-hr experiments at pressures of 1,000 psig and above. The Ti02 product is porous owing to the removal of the iron, has the rutile crystal structure, and is suitable for chlorination. Waste disposal problems associated with the process would be minimal because the iron pentacarbonyl can be decomposed to produce iron powder or pellets for sale and CO for recycling.

Jan 1, 1973

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By W. H. Gauvin, N. J. Themelis

I N ADDITION to its practical importance in the beneficiation of iron ores and in direct-iron processes, the study of the reduction of iron oxides involves many aspects of challenging theoretical interest. The complexity of the reduction process combined with the fact that under different experimental conditions the controlling stage for the reaction may not necessarily be the same, has led experimenters in this field to a wide diversity of opinion regarding the reaction mecl1anism. As a rule, each investigation has been restricted to the study of one or two variables over a comparative]~• narrow range of experimental conditions, and consequently, it be-comes necessary to examine the significance of each published work in the light of the results of other experimenters in the field.

Jan 1, 1962

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By M. K. Han, K. N. Han, P. B. Queneau, W. J. Dawson

The development and scale up of hydrothermal synthesis processes for manufacture of high performance materials is discussed. Traditional hydrometallurgical processes are reviewed, leading into a discussion of process development concerns for manufacture of modern materials. Three case studies are presented, including a piezoelectric ceramic, barium titanate for multiyear capacitors, and high purity chromium metal. Factors for selection of reactor design are presented, as well as results of scale-up studies on the three products.

Jan 1, 1993

By D. M. Muir

The mineralogy of residues formed during the pressure acid leaching of arid region nickel laterite ore varies according to the salinity of the process water, alkali cation additives and the overall acid loading. In fresh water, hematite is the main iron-bearing leach residue component, together with amorphous silica and hydronium or sodium alunite/jarosite [(H3O,Na)(Fe,Al)3(SO4)2(OH)6]. As the process water salinity increases, or as NH4+ or K salts are added, alunite/jarosite is the kinetically favoured iron-bearing phase accompanied by an increase in acid consumption. The alunite/jarosite appears as two XRD distinct phases with different Fe:Al molar ratios. In weakly saline water, iron-rich alunite/jarosite slowly transforms to hematite and an aluminium-rich alunite/jarosite together with the release of acid. The addition of potassium salts forms a more stable alunite/jarosite whilst the addition of ammonium salts leads to greater transformation of alunite/jarosite at 250°C. Weakly saline process water gives enhanced nickel recoveries, whilst strongly saline process water gives lower nickel recoveries but higher soluble iron because of chloro-complexation. SEM and microprobe analysis shows very little nickel is associated with the alunite/jarosite and hematite phases. Nickel losses to the residues are attributed to adsorption on amorphous silica and to a lesser extent on alunite/jarosite.

Jan 1, 2006

By J. F. Wilson

Steady-state flow theory, previously applied to displacements with two mobile phases, is extended to cover down-structure flow involving three mobile phases: oil, gas and water. When used with normal reservoir fluid properties, the theory predicts the existence of four distinct flow regimes and the conditions under which each regime exists. The predicted behavior is verified by a parallel-plate model study. INTRODUCTION Special problems exist when a water flood is contemplated in a dipping reservoir having a substantial gas cap. Normally, the gas-cap region is one of very low oil saturation. If oil is moved into the gas cap during the flood, a loss in recovery results. Efficient recovery of the oil underlying the gas is therefore difficult. In two reported field water floods, injection into the gas cap has been used to solve these problems. At the West Norfolk Garr Sand Unit, injection into the upstructure region of the reservoir was made for the stated purpose of filling up the gas cap with water.' The purpose in the Sholem Alechem Fault Block "A" Sims Sand Unit was to form a continuous water barrier between the gas cap and oil band.' A laboratory model study preceded this flood and was described in the same publication. Both of these gas-cap water injections gave satisfactory results, but the published data are insufficient to allow generalizing to other field conditions. The present investigation was also undertaken to obtain results for a specific field problem. However, these results will be shown to be in agreement with an extension of the Dietz3-5 mathematical model to three-phase flowing systems. The agreement between the theory and the model studies indicates that the mathematical model can be used to describe completely the flowing system under some conditions, and to indicate the general type of flow to be expected under all conditions. FLOW THEORY The Dietz equations for two-phase flow are derived "' for the case of constant-velocity linear flow in a homog- eneous porous medium. The transition zone between the fluids is assumed to be of negligible extent so that the displaced and displacing fluids are separated by a sharply defined interface, as illustrated in Fig. 1. The density and mobility of the displacing fluid are constant over the region behind the interface, and the same properties of the displaced fluid are constant over the region ahead of the interface. To extend the Dietz equations to three-phase systems, we postulate the flowing system shown in Fig. 2 and determine the conditions under which it can exist. The

By Thomas Cox

This paper makes no claim to any new idea; it simply reviews the Treasury Department Regulations pertaining to the practical application of depreciation and depletion and other allowances governing taxation of oil and gas properties. Other methods may be existent, but as they may not conform to the legal status they must be discarded. In complying with the present laws governing the industry with regard to taxation and the allowable deductions therefrom, the following considerations are essential: Depletion, depreciation, amortization, other allowances, and items not, deductible. It is definitely understood that depletion is the loss or exhaustion sustained in the continuous operating of an oil and gas property, and that each unit of oil or gas taken out reduces the value of the property until its final exhaustion. Depletion applies only to the natural deposits of oil and gas due to their removal in the course of exploitation of any property. Depreciation is defined to cover the waste of assets due to exhaustion, wear and tear, and obsolescence of the physical property, and is separate and distinct from depletion; its allowance is that amount which should be set aside for the taxable year in such sums as for the useful life of the property will suffice to repay its original cost—or its value as of Mar. 1, 1913, if acquired by the taxpayer before that date—less the salvage value at the end of such useful life. Amortization is allowed for such facilities as were built or acquired on or after Apr. 6, 1917, for the production of articles contributing to the prosecution of the war and, in the case of vessels, those built and acquired after that date. The amount to be extinguished, in general, is the excess of the unextinguished or unrecovered cost of the property over its maximum value under stable post-war conditions. Claims for amortization must be unmistakably differentiated in the returns from all other claims of depreciation. The taxpayer is also required to furnish full information with the claims for amortization to the full satisfaction of the Commissioner. Further reference is directed to the specific rules and regulations for making these claims.

Jan 1, 1921

By D. E. Ranta, William B. Ryan, Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1992

By J. M. King, C. J. Boggs

Acquisitions of mineral properties and companies can saddle the acquirer with unexpected and substantial liabilities and obligations incurred by the acquired or selling company that are not readily apparent from review of the company's books or files. This paper will address selected areas of concern, such as environmental and reclamation liabilities, problems of foreign ownership by the buyer or seller, pension obligations, plant closing laws, effective title review, land use and zoning.

Jan 1, 1992

By G. A. Irona

Solids injection into non-ferrous converters and furnaces is becoming increasingly important for concentrate injection, removal of impurities, and recycling of dusts and other waste materials. The fundamental design aspects of these technologies will be reviewed, including gas and particle trajectories, lance clogging, heat transfer, and mass transfer including reaction rates and mixing. The use of soda ash for removal of impurities such as antimony and selenium will be used as an example of versatility of powder injection processes.

Jan 1, 1993

By S Romanchuk, V N. Macvkiw, D. J. I. Evans

The paper describes the processes developed and piloted by Sherritt Gordon Mines Limited for recovering copper, in the form of specification copper powders, from Lynn Lake sulphidic copper concentrates and Fort Saskatchewan Refinery by-product copper sulphides. The process includes ammonia pressure leaching and hydrogen reduction from solution. Nickel and cobalt present in the con-centrates dissolve in the leach solution and a method was developed for separating these metals from the cop-per. Methods are described for con-trolling the physical properties of the copper powder produced in the reduction vessel. The chemistry of the process is briefly discussed and the effects of some of the more important process variables are described. SHERRITT Gordon Mines Limited have developed and proven on a pilot plant scale, a process (I) for the production of copper powder

Jan 1, 1961

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By D. Debasis, Christopher Mark, Gregory M. Molinda

The stability of any underground opening is, in large part, a function of the strength of the rock mass which surrounds it. The Coal Mine Roof Rating (CMRR) has been developed to quantify the defects in the rock mass and compile a strength value which can be used for engineering design. The CMRR has been applied to a number of ground stability problems, including chain pillar design, roof bolt selection, hazard assessment, intersection design, and numerical modeling. The CMRR procedure and some of these applications are described in this paper. The CMRR will soon be available in a Visual Basic computer program, allowing easy integration into exploration programs and standard roof fall assessments.

By G. Bourque

One of the design criteria for the Mount Wright facilities was to incorporate the latest proven automation techniques and devices for the new crushing, grinding and concentrating plant. The heart of the centralized control system is a Fox 1 process computer, located in the central control room in the administration building. The entire operation, i.e. crushing, conveying, storing, grinding and concentrating, is monitored and controlled, through the process computer , by one operator via a CRT console. In case of computer failure, the control is automatically, and without process interruption, transferred to manual back-up panels. One of the newest management tools, the process computer is programmed to collect and automatically print out shift. daily and monthly reports on tonnage, metallurgy and equipment operating time, for better planning of operations and preventative maintenance.

Jan 1, 1977