Search Documents

By L. L. Wyman

Since the presentation, by the writer, of the initial paper on the embrittlement of copper,1 the subject has been investigated further along two separate lines. The first series of investigations involves the "double-deoxidized" coppers, while the second series is devoted to single deoxidizers other than those used in the investigations reported upon last year. The object of these experiments is to develop a type of copper that will show the minimum of detrimental effects after having been exposed to alternate oxidation and reduction. The fabrication of this material necessitates the use of alternate oxidizing and reducing atmospheres, at temperatures ranging up to 900" C. Following this treatment it is essential that the soundness and strength of the copper be unimpaired, even in sections of only a few thousandths of an inch in thickness. Materials The ensuing report embodies three separate groups of materials, which may be classified as follows: 1. Double-deoxidized copper using silicon and calcium boride. 2. Copper deoxidized with calcium. 3. Double-deoxidized copper using constant calcium content (0.075 per cent) plus silicon, or calcium boride. Last year, T. S. Fuller, of the General Electric Research Laboratory, suggested that if a properly deoxidized copper had sufficient deoxidizer residual in the material, this excess material might increase the resistance of the copper to the oxidation reduction cycle. In consequence of this suggestion, two small lots of "double-deoxidized" copper were prepared. The first, lot A, was made by adding 0.03 per cent silicon as the deoxidizer, following this by an addition of 0.55 per cent calcium boride immediately before pouring. The second, lot B, contained the same ingredients, but these were added in the reverse manner. Inasmuch as these lots were tested separately from the materials about to be described, it must be borne in mind that the materials cannot be grouped together, and are not directly comparable.

Jan 1, 1933

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By P J. Ellen

The selection of the ore haulage system is a key decision made in the development of an underground mine. The haulage system is one of the components that define a mineÆs ability to respond to changes in mining inventory and market conditions. The complexity of this decision for Telfer Deeps was affected by the realisation during the feasibility process that the true scale of the potential underground mineralisation at Telfer was still to be quantified. This paper provides an overview of the process used in the Telfer Project Feasibility Study to select an ore haulage system for Telfer Deeps. The purpose is to highlight the value of impartially approaching tasks of this type with a robust process. The process should be able to respond to issues identified as the task progresses towards the objective of finding the best solution for an ore haulage system for the mine. For Telfer Deeps, this process resulted in the selection of a haulage system built around a shaft. The systems considered during the feasibility are discussed and the components of the haulage system constructed for Telfer Deeps are described.

Jan 1, 2005

By Daniel Edelstein

Demand for arsenic trioxide dropped markedly during 1983, primarily as a result of a 27% reduction in cotton planting. As an oversupply of arsenic trioxide developed, prices declined for both domestic and imported material. Domestic Data Coverage.-Commercial-grade arsenic trioxide and arsenic metal were produced by only one U.S. company, which voluntarily reported its production to the Bureau of Mines. To prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1984

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By J. B. Gayle

The Bureau of Mines sole-heated oven has been used for studying coal expansion for some 20 years. During the period before 1940 emphasis was placed on studies of the mechanism of coal expansion and the effects of variations in operating conditions on the results. Since 1940 emphasis has shifted to a survey of the expansion properties of various coking coals. Because additional information concerning a number of unsolved problems in connection with the earlier studies appeared highly desirable, this investigation of the use of sole-heated ovens for studying coal expansion was undertaken. The principal findings, in order of their discussion in the text, may be summarized as follows. 1. Expansion results for binary blends of coking coals exhibit nonadditive behavior, both positive and negative deviations from additive behavior being noted, depending on the particular coals tested. Additive behavior can be achieved, however, either by charging the blend components in separate layers (which indicates that the observed phenomena are not characteristic of the particular expansion oven used) or by testing relatively coarse sizes of coal (which suggests that the effects of crushing on the expansion properties of coking coals may be even more complex than is generally recognized).

Jan 1, 1959

The general principles of technical due diligence best practice that are involved in assessing a mineral property in the early stages of its development are described and a bibliography of relevant papers is attached. The issues specific to the evaluation of gold deposits are highlighted. The Australasian Institute of Mining and Metallurgy's (The AusIMM) initiatives in this area, dealing with the proper public reporting of Reserve/Resource information (JORC Code) and property assessment/valuation (VALMIN Code), will be used as a framework against which the illegal tampering with drilling samples to artificially boost their gold content (salting) from the Busang gold deposit (Kalimantan, Indonesia), owned by Bre-X Minerals Limited (Calgary, Canada), will be reviewed. While the Busang saga was based upon fraud, through salting the samples, the general lessons to learn from such a scam are worth documenting. In Australia, most of those working in the mineral industry belong to long established professional institutes and consultant associations (eg The AusIMM or Mineral Industry Consultants Association [MICA]) that require their members to work within their technical limits and to comply with best practice guidelines, or risk being judged and found wanting by their peers in the context of strong Ethics Codes. There is also a strong interface between such representative professional bodies and the corporate and financial market regulators (ASC/ASX), which closes the monitoring loop. Canada has only now seen the wisdom of having this type of early warning system in place. Fraud and deliberate deception will be always possible, but deception on the enormous scale that occurred at Busang is most unlikely with proper surveillance systems in place and the use of accredited technical professionals. There should have been more hard data available about so big and rich a deposit owned by a C$6Bn company.

Jan 1, 1997

By H. C. George

This report presents a comprehensive tabulation of lifting cost data collected from oil companies in many different fields. These data were collected during the writer's studies of surface equipment and methods of pumping oil wells, in practically all of the important oil fields in the United States and are based on average operating conditions at 57 groups of properties with a total of 4,497 producing wells. Although lifting cost is only a part of the total cost of producing oil, it nevertheless gives a representative cost figure for purposes of comparison.

Jan 1, 1923

By P. Nelson, K. L. Gunsallus, A. R. Ingraffea, J. F. Beech

INTRODUCTION Fracture toughness, KIC, is an intrinsic material property and is a measure of the energy required to create new surface area in a material. Fracture toughness measurements can be made for a wide range of rock types (Ouchterlony, 1980). As a measure of energy of comminution, fracture toughness might be used for more sensitive predictions of Tunnel Boring Machine (TRM) performance than are possible with other index measures in current use. This paper describes part of an ongoing, comprehensive, analytical/experimental program aimed at evaluation of KIC in such a role. The program includes efforts to: 1. Provide a firm analytical basis for a test specimen geometry: the core-derived short-rod. 2. Develop simple, inexpensive testing equipment and techniques. 3. Evaluate the accuracy of the above by testing rock and other materials and comparing the measured fracture toughness with those obtained by other methods. 4. Measure fracture toughness of a substantial number of different rocks from three ongoing TBM projects. 5. Compare fracture toughness results with other strength measures. 6. Compare all test results with observed TBM performance in the three projects. Presented here are summaries of all but the last of these efforts. Comparative evaluation of KIC as a more senstive rock property for TBM performance prediction will be the subject of the oral presentation and a subsequent paper.

Jan 1, 1982

By L. W. Higley

Particulates generated in electric furnace (EF) steelmaking constitute approximately 1 to 2 pct of the charge. This flue dust is a rich source of zinc (values are substantially higher than in ore), but although there are several processes for recovering the metal, none are considered economic in the United States. This report reviews extraction technology and presents results of Bureau of Mines reduction-volatilization tests on pelletized EF dusts which achieved high recoveries of zinc. The data are sufficiently encouraging to warrant consideration of EF dusts as raw material for primary zinc smelters.

Jan 1, 1977

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By Pedro Hugo Tumialán

El presente texto señala el proceso de mineralización del yacimiento metálico de Algamarca en Cajamarca a través de la descripción de la singularidad de sus características geológicas. De acuerdo a ello, se corta una inclinal de cuarcita de la formación Chimú del Cretáceo inferior, cuyo eje tiene un rumbo NW concordante al eje del anticlinal. Asimismo, el intrusivo Caupur es el causante de la mineralización de las vetas de Algamarca, las cuales resultaron por fuerza de compresión perpendicular al eje del anticlinal, formando algunas vetas dextrales y sinestrales, así como vetas de tensión perpendiculares al eje anticlinal. En este sentido, las vetas son angostas (O.la 0.3 m)peroricas en plata y su distribución se da en forma de arco de cada veta.

Nov 8, 1982

By L Faulkner

The Tarnagulla Gold Project in Central Victoria, Australia, was developed and operated by Reef Mining NL between 1994 and early 2000, producing 53 000 ounces of gold from the Nick OÆTime Shoot, a single narrow vein shoot structure within part of the larger Poverty Reef, with a strike length ranging from 30 m to 60 m. The ore shoot was developed over a vertical interval of 190 m, using a small cross-section decline and small, mechanised equipment. Various stoping methods were employed including mechanised cut-and-fill with a single boom jumbo, hand-held mining using airleg drills and rope scrapers, and small uphole retreat stopes using a line of sight remote operated LHD to recover a crown pillar. Experience during stoping showed that airleg drilling and rope scrapers gave much better dilution control than diesel equipment. Innovations included a low-cost hydraulic fill system. Due to the small scale of the deposit, the feasibility studies, planning and permitting for the mine were based on very limited drilling information; however, the mine was brought into production within two years of the discovery. While the mine made an operating profit, it failed to fully repay capital at the low gold price then prevailing. Applying the lessons learned from the operation to optimise the access and stoping method, the project is re-examined at todayÆs gold price and operating costs. Central Victoria has the potential to host many similar small deposits. The authors were respectively Non-Executive Director and Resident Manager for Reef Mining NL when the mine was operating.

Jan 1, 2008

By Mark J. Klein

The behavior of nitrogen in Cr-0.12 at. pct Y was studied in specimens of varying interstitial concentration and thermal history. It was found that soluble nitrogen can be introduced into this alloy by increasing the concentrations of either oxygen or nitrogen. For low nitrogen concentrations the nitrogen in solution is low relative to that in unalloyed chromium. However, the nitrogen in solution increases with increasing nitrogen concentration, approaching that in unalloyed chromium. When the alloy is supersaturated with nitrogen, the nitrogen precipitates readily from solution as a chromium nitride. The stress -induced relaxation of nitrogen is influenced by internal oxidation or internal nitrification of this alloy. THE addition of small concentrations of reactive elements such as yttrium have been found to enhance the low-temperature ductility of chromium.&apos; However, the mechanism by which the ductility is increased is not known. It has been suggested that this effect is caused by a drastic reduction in the concentration of nitrogen retained in solution and therefore a decrease in the number of dislocations locked by nitrogen, a factor that has been associated with an increase in ductility.1,2 However, a change in the type of interstitial precipitate induced by yttrium could also contribute to enhanced ductility of the alloy, since chromium nitride precipitates appear to be embrittling.&apos; In this regard, it has been shown that yttrium scavenges nitrogen in chromium to form YN,4 thus reducing the embrittling chromium nitride phase. However, the change in nitrogen solubility induced by yttrium and the partition of nitrogen between chromium and yttrium nitrides are not known. The object of this investigation is to study the effect of yttrium on the behavior of nitrogen in chromium to obtain information relevant to the mechanism by which scavengers enhance the ductility of chromium. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation have been described in detail elsewhere.5,6 Wires of Cr-0.12 at. pct Y, 15 cm in length and 1 mm in diam, were drawn from rods 0.6 cm in diam supplied by the General Electric Co. The grain size of the wires after recrystallization at 1150°C was somewhat nonuniform, varying from 0.006 to 0.06 mm in diam. The interstitial analysis for the wires in ppm by weight was about 160 0, 80 N, 12 C, and <2 H. Heat treatments were carried out after encapsulation of the specimens in quartz tubes containing argon. Changes in interstitial concentrations, or interstitial "loading" as it is termed in this study, were generally accomplished by annealing in oxygen, ammonia or methane at 1150°C. The internal friction was measured using a conventional torsional pendulum enclosed in an evacuated chamber. Electrical-resistivity measurements were made at liquid-nitrogen temperature.

Jan 1, 1967

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By J. L. Hoffman, F. W. Wood, R. A. Beall, W. E. Anable

For melting and purifying reactive and refractory metals , two electronbeam furnaces have been constructed and operated on the principle of highpowered vacuum diodes . It was necessary to design the vacuum and electrical systems , mechanical features , and operating procedures to cope with dynamic conditions . Vacuums of 10-5 torr , tens of kilowatts of power at 5 to 10 kilovolts , and the evolution of impurities at thousands of liters per minute constitute a challenging combination . The furnaces have been used to melt either button specimens weighing several hundred grams or , by feeding material as a consumable electrode , small ingots weighing several kilograms . Hafnium is among the metals that can be purified . For example , hafnium starting material with Rhn 94B was softened to Rhn 70B after 2 hours of melting under a 25 - kw electron beam , and impurity levels were reduced as follows : Oxygen , from 700 to 350 ppm ; nitrogen , from 71 to 20 ppm ; hydrogen , from 6 to 1 ppm ; aluminum from 75 to < 20 ppm ; chromium , from 80 to < 10 ppm ; iron , from 100 to 40 ppm ; and silicon , from 40 to < 20 ppm .

Jan 1, 1963

By C. W. Dwiggins

The Bureau of Mines characterized the chemical and physical properties of metallo-organic materials in petroleum to determine their effect on petroleum production and refining. The structures and physical properties of porphyrins and materials that normally contain metalloporphyrins such as crude oils and asphaltenes were investigated using elemental analysis, NMR analysis, absorption spectrometry, and small-angle X-ray scattering. Petroleum fractions greatly enriched in metalloporphyrins were obtained using asphaltene precipitation, liquid extraction, and large-scale liquid-solid chromatography. Selected fractions containing porphyrins were further purified by chromatographic methods, crystallization, and demetalation followed by chromatography. Nonporphyrin metals could not be appreciably concentrated from the bulk of the asphaltene.

Jan 1, 1969

By J. W. Town

This report summarizes the results of laboratory investigations conducted by the Federal Bureau of Mines to obtain hydrometallurgical information on the dissolution of mercury sulfides from ores, flotation concentrates, and pure mercuric sulfides. Statistical methods were used to design the experiments and evaluate the resulting data. Studies demonstrated that cinnabar is readily soluble in sodium sulfide, partly soluble in potassium sulfide, and essentially insoluble in ammonium sulfide. Additions of sodium hydroxide or potassium hydroxide to sodium sulfide solutions increased mercury extraction slightly; when either was added to potassium sulfide or ammonium sulfide solutions, mercury extraction was equal to that of sodium sulfide. Tests at the Albany Metallurgy Research Center showed that sodium sulfide would completely dissolve chemically pure mercuric sulfide, more than 95 percent of the cinnabar in 5-percent mercury flotation concentrates, and 60 to 90 percent of the cinnabar in low-grade ores. The double-leach tests showed that potassium sulfide would dissolve over 90 percent of the arsenic in mercury-arsenic products and 1 to 10 percent of the mercury; then sodium sulfide-hydroxide solutions would dissolve 80 to 90 percent of the remaining mercury and 5 to 10 percent of the arsenic.

Jan 1, 1961